This high-quality replacement air intake hose is designed for 1.4 HDi (66 kW) diesel engines used in selected Citroën and Peugeot models. Ideal for professional garages and DIY mechanics, the hose restores correct air flow to the engine, prevents vacuum leaks and helps maintain fuel economy and engine response. Commonly searched by OE numbers 9646926280 and 143422, this part is a direct-fit solution for vehicles that require reliable intake plumbing.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C3; Peugeot 1007
• Product Codes: 9646926280
• Other Numbers: 143422

Function And Fitment

The intake hose channels filtered air from the airbox toward the engine intake tract and turbocharger on turbocharged variants. It must maintain an airtight connection under varying boost and vacuum conditions. A properly fitted hose ensures stable air metering, consistent turbo response and prevents unmetered air from causing rough idling or reduced power.

How To Replace

Replacement is straightforward for a competent mechanic or experienced DIYer. Typical steps:

• Park the vehicle on a level surface, let the engine cool and disconnect the negative battery terminal if working near sensors.
• Loosen and remove the clamps securing the hose at the airbox and at the intake/turbo inlet.
• Carefully detach any vacuum lines, breather hoses or sensor connectors attached to the hose—label them if needed.
• Remove the worn hose and inspect mating surfaces for oil, debris or sharp edges; clean before fitting the new hose.
• Install the new hose, fit clamps evenly and tighten to hand-firm plus a small additional turn—avoid over-tightening plastic fittings.
• Reattach any removed lines or sensors and verify all connections. Start the engine and check for leaks or abnormal noises.

Installation Recommendations

• Use quality stainless or plated clamps; replace brittle or corroded clamps rather than reusing them.
• Inspect adjacent components (airbox seals, throttle body, intercooler piping) and replace any damaged parts to avoid repeating failures.
• Ensure sensor connectors and vacuum lines are seated correctly to prevent fault codes.
• After installation, perform a visual leak check at idle and under light load; scan for engine fault codes if available.

Why This Part Commonly Fails

Intake hoses are exposed to heat cycles, engine bay vibration and oil contamination from the crankcase breather. Over time the rubber or silicone can harden, crack or split at bend points and clamp locations. Common failure causes include:

• Age-related material degradation leading to cracks and splits.
• Oil and soot build-up from the breather system accelerating rubber deterioration.
• Loose or corroded clamps allowing the hose to slip under boost or vacuum, causing leaks.
• Physical damage from improper routing or contact with hot components.

Symptoms of a failing intake hose include loss of power, irregular idle, turbo lag on turbocharged engines and illuminated engine warning lights due to incorrect air metering. Replacing a degraded hose typically restores engine performance and drivability.

Part numbers 9646926280 and 143422 are frequently used when searching for a direct-replacement intake hose for 1.4 HDi 66 kW Citroën and Peugeot applications; verify fitment against your vehicle model and engine code before installation.

Intake hose 1.4 HDi 16V – PSA 0382.Y7 (0382Y7) for Citroën and Peugeot

Used original PSA part for the compressed air line in the intake/turbo system. This is an air connection at the exchanger (intercooler) for 1.4 HDi 16V engines, typically in more powerful versions with an intercooler. A correct, leak-free hose is key to full turbo performance, low consumption and flawless boost pressure readings.

Why choose this part?
– OEM accuracy: original shaping and diameters, assurance of correct seating without modifications
– Performance restoration: solves pressure leaks, whistling, oil maps around joints and power fluctuations
– Economical choice: significantly cheaper than a new part, the function of the original is preserved

Technical information
– OEM/PSA number: 0382.Y7, 0382Y7, 0382 Y7
– Designation: intake hose / turbo intake pressure hose, connection at the intercooler
– Location: section of the air line around the intake intercooler (exchanger).
– Engine: 1.4 HDi 16V (DV4 series) – selected versions with intercooler
– Material: molded rubber/plastic with quick couplings according to OE design
– Purpose: Citroën and Peugeot, e.g. Citroën C3 and Peugeot 1007 with 1.4 HDi engine (verify by VIN and OEM number)

Compatibility
– Primarily designed for Citroën and Peugeot cars with 1.4 HDi 16V engine and intercooler
– Always compare OEM code 0382.Y7 with your original part or verify by VIN to ensure match

Typical symptoms of a faulty hose
– Hissing under load, loss of power, higher smoke
– Oil smearing around hose connections, low boost pressure error message

Installation recommendations
– Check seals/O-rings and clips; replace the damaged one
– Before assembly, clean the mating surfaces and pipes to ensure tightness
– After installation, carry out a leak check and test run under load

Condition and packaging
– Used original PSA part
– Condition and completeness according to photos; included is what can be seen in the photos (clips/quick connectors only if they are in the photos)

Search terms (SEO)
– intake hose 1.4 HDi 16V 0382Y7
– Citroën C3 1.4 HDi turbo pressure hose
– intake hose intercooler Peugeot 1007 0382.Y7
– PSA air intake hose 0382 Y7

Note: Different versions of the 1.4 HDi engine differ in intake distribution. Always check your car’s OEM number 0382.Y7 and VIN for compatibility before purchasing.

Original intake/intercooler hose PSA 0382Y6 (0382.Y6) for 1.4 HDi 16V 66 kW (DV4TED4) engines for Citroën and Peugeot cars. Used original part removed from the car – ideal replacement for cracks, oil leaks or loss of pressure between the intercooler and the intake. Properly sealing hoses will improve engine thrust, reduce turbo whistling and unstable idling.

Key features
– OE number (PSA): 0382Y6 / 0382.Y6 / 0382 Y6
– Part designation: intake hose, turbo hose, intercooler hose (exchanger outlet)
– Engine: 1.4 HDi 16V, 66 kW, code DV4TED4
– Location: section near the exchanger (intercooler) – compressed air line towards the intake pipe
– Design: molded pressure hose; ends for quick connection to the respective sockets
– Condition: used original part; normal signs of use, functionality according to the condition in the photos
– Accessories: clips/gaskets not usually included – we recommend installing new O-rings and clips

Compatibility
– Citroën: especially C3 1.4 HDi 16V 66 kW (DV4TED4), according to OE number
– Peugeot: selected models with 1.4 HDi 16V 66 kW (DV4TED4) engine, according to OE number
Note: Within the PSA, different hose shapes were installed depending on the year of manufacture and body type. Always compare OE number 0382Y6 and shape/connectors to your original part or verify by VIN.

Typical symptoms of a faulty hose
– Loss of power, increased smoke, whistling turbo, oil maps around the joint at the intercooler
– Filling pressure control errors (over/underboost) and consumption increase

Assembly tips
– Before assembly, clean the contact surfaces and check the intercooler and intake nozzles
– Replace the sealing O-rings and use quality clips with sufficient tightening torque
– After installation, perform a visual and pressure check for leaks in the entire intake manifold

Search terms (SEO)
– Intake hose 1.4 HDi 16V 66 kW, intercooler hose 0382Y6, turbo hose PSA 0382.Y6, air intake at Citroën C3 exchanger, DV4TED4 intake hose, original used Citroën/Peugeot part

This part is suitable if you are looking for a direct replacement according to the number 0382Y6 without the need for modifications. Verify compatibility before ordering – preferably by comparing the OE number and shape to your original part.

High-quality air intake neck for the 1.4 HDi 66 kW diesel engines used in select Citroën and Peugeot models. This intake hose ensures reliable airflow from the airbox/turbo area to the engine intake tract, helping to maintain engine responsiveness and fuel efficiency. The part is often searched by its product codes, so listing the reference numbers below will help fast identification for both professional workshops and DIY enthusiasts.

This replacement component is suitable for routine maintenance or when diagnosing poor performance, rough idling, or intake air leaks. Constructed to withstand engine bay temperatures and typical vibration, it restores the original sealing and prevents unmetered air entering the intake system, which can otherwise trigger fault codes or cause drivability issues.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C3; Peugeot 1007; 1.4 HDi 66 kW applications
• Product Codes: 9641464480, 143421
• Additional Numbers: NFP

Fitment And Function

The intake neck connects the air filter housing and upstream components to the turbocharger/intake manifold area on 1.4 HDi 66 kW engines. Its primary function is to deliver filtered air while keeping the charge air path sealed. Proper sealing prevents loss of boost, incorrect air mass readings, and related engine management faults.

Installation Recommendations

• Allow The Engine To Cool Before Starting Work To Avoid Burns.
• Remove Any Engine Covers And Unclip The Airbox To Access The Intake Neck.
• Loosen Hose Clamps And Any Fasteners Securing The Old Hose; Inspect Clamps For Corrosion And Replace If Necessary.
• Check Surrounding Components (Airbox, Turbo Inlet, MAF Sensor) For Oil Residue, Cracks Or Debris Before Fitting The New Hose.
• Install The New Intake Neck In The Correct Orientation, Seat It Fully On Both Connections And Tighten Clamps Evenly—Avoid Over-Tightening That Could Damage The Hose.
• After Installation, Start The Engine And Check For Leaks, Unusual Noises Or Fault Codes; Confirm Normal Idle And Driveability.

Why This Part Commonly Fails

Intake hoses and necks commonly deteriorate due to heat cycling, exposure to engine oil or fuel vapors, and mechanical abrasion from engine movement. Rubber and polymer materials can harden and crack with age, clamps may corrode or lose tension, and small tears can allow unmetered air to enter the intake system. Vehicles with frequent short trips, high mileage, or oil leaks are more likely to experience premature hose failure.

Quick Replacement Tips For Mechanics And DIYers

• Inspect Clamps And Replace With New Worm-Drive Or T-Bolt Clamps If Old Ones Are Stretched Or Corroded.
• Clean Mating Surfaces And Remove Any Residual Oil To Ensure A Secure Seal.
• Verify Correct Part Number Before Fitting To Ensure Proper Fitment And Orientation.
• Keep A Small Inventory Of Commonly Replaced Intake Hoses And Clamps In The Workshop To Reduce Vehicle Downtime.

If the engine shows signs of poor performance after replacement, recheck connections and inspect the mass air flow sensor and turbo inlet for contamination or damage.

The replacement of this hose is necessary when it shows signs of wear, such as cracks or leaks, which can lead to reduced engine performance and increased fuel consumption. Regular inspections and timely replacements can help avoid performance issues and costly repairs.

Technical Information:

• Manufacturer: Citroën/Peugeot
• Model: 1.4 HDI
• Product Codes: 143413, 1434F6
• Other Numbers: N/A

Note: Clamps may not be included with the product.

This EGR (Exhaust Gas Recirculation) pipe is a direct-fit replacement designed for Citroën and Peugeot 1.4 HDi diesel engines. It restores the correct routing of recirculated exhaust gases between the EGR valve and the intake system, helping to control NOx emissions and maintain engine efficiency. The part is commonly referenced under OEM codes 9643982180 and 1628ZY, making it easy to find in parts catalogs or when searching by product number.

Technical Information

• Manufacturer: Stellantis (Citroën, Peugeot)
• Model: Citroën C3; Peugeot 1007
• Product Codes: 9643982180, 1628ZY, NFP
• Other Numbers: 1628ZY, 9643982180
• Engine: 1.4 HDi 16V (Engine Code 8HY), 66 kW

Fitment And Function

The pipe connects the EGR valve circuit to the intake manifold/turbo system depending on configuration. Its role is to recirculate a metered amount of exhaust gas back into the intake to lower combustion temperatures and reduce nitrogen oxide emissions. Correct fitment is essential to avoid leaks, boost loss, or incorrect EGR operation.

Installation Recommendations

Replace The Part With The Engine Cold. Remove Any Engine Covers That Restrict Access. Loosen Clamps And Fasteners At The EGR Valve And At The Intake/Turbo Connections, Carefully Remove The Old Pipe And Clean The Mating Surfaces. Replace All Gaskets And Sealing Rings During Installation. Tighten Fasteners To The Manufacturer’S Torque Specifications Where Available. After Installation, Start The Engine And Check For Exhaust Leaks, Boost Leaks, And Any Diagnostic Trouble Codes. If You’Re Not Confident With The Procedure, Have The Job Performed By An Experienced Technician.

Common Failure Reasons

EGR Pipes Typically Fail Due To Soot Accumulation, Which Can Restrict Flow Or Cause Backpressure. Thermal Stress And Vibration Over Time Can Lead To Cracks Or Fractures In The Pipe Or At The Flange Joints. Failed Or Worn Gaskets And Clamps Also Cause Leaks That Lead To Poor Idle, Loss Of Power, Increased Emissions, And Check Engine Light Warnings. Corrosion From Condensation And Aggressive Duty Cycles (Short Trips) Accelerates Wear.

How To Recognize A Faulty EGR Pipe

• Illuminated Check Engine Light Or Fault Codes Related To EGR Or Intake Leaks
• Rough Idle, Hesitation, Or Noticeable Loss Of Power
• Black Smoke From The Exhaust Or Increased Fuel Consumption
• Hissing Or Exhaust Smell From Engine Bay Indicating A Leak

Service Life

Service Life Depends On Driving Conditions And Maintenance. In General, Signs Of Trouble Often Appear After Long Service Intervals (Commonly Observed From Around 100,000 Km Upwards), But Actual Durability Varies With Usage, Fuel Quality, And EGR System Maintenance.

Why Choose This Part

Using The Correct EGR Pipe With Matching OEM Codes Ensures Proper Fit And Reliable EGR Function. Replacing A Damaged Or Leaking Pipe Restores Engine Performance, Reduces Emissions, And Prevents Secondary Damage To Turbochargers And Intake Components Caused By Exhaust Leaks Or Excessive Soot Buildup.

This replacement turbo intake hose is intended for 1.4 HDI engines and restores reliable airflow between the turbocharger/intercooler and the intake tract. Suitable for professional workshops and do-it-yourself mechanics, the hose improves throttle response and eliminates boost leaks that cause poor engine performance. The part is commonly searched by product codes 9646926180 and 143423, making identification and ordering fast.

Technical Information

Manufacturer: Citroën / Peugeot (Stellantis)
Model: Citroën C3; Peugeot 1007
Product Codes: 9646926180, 143423
Additional Numbers: 143423

Installation Recommendation

Allow the engine to cool before starting. Release boost pressure by letting the engine idle and then switching it off. Loosen clamps at both ends of the hose and remove the old hose; inspect mating surfaces for oil or damage and clean them. Fit the new hose in the correct orientation, secure with new or inspected clamps and tighten evenly. After installation, start the engine and check for boost leaks and proper idle. Replace clamps if corroded and inspect the intercooler and turbo connections while working.

Why This Part Fails Most Often

Hoses in the turbo intake circuit are exposed to heat cycles, oil contamination and mechanical stress. Over time rubber can harden, crack or swell from contact with oil or high temperatures. Improper clamp torque or impact from road debris can cause air leaks. Symptoms of a failing hose include hissing noises under boost, reduced acceleration, increased fuel consumption and sometimes fault codes related to boost pressure. Regular inspection during scheduled maintenance helps detect early wear.

Are you looking for a reliable replacement part for your Citroën or Peugeot vehicle? Our water hose for the 1.5 HDI engine is the perfect choice for both mechanics and DIY enthusiasts seeking a quality and affordable solution for their vehicle repair. This part has been carefully removed from the vehicle and is ready for immediate installation.

The main advantage of this water hose is its perfect compatibility with Citroën and Peugeot models, ensuring smooth installation and functionality. It is frequently searched under the product number 9812441980, which simplifies identification and ordering.

Technical Information:

• Manufacturer: OEM for Citroën and Peugeot
• Models: Citroën Berlingo III, Fiat Doblo III, Opel Combo E K9, Peugeot Rifter, Toyota ProAce City
• Product Codes: 9812441980
• Additional Numbers: Not available

The water hose is a crucial component of the vehicle’s cooling system; regular inspection and replacement can prevent serious engine damage caused by overheating. As it is a key component in the cooling system, we recommend replacing it at the first signs of wear or damage.

This part is ideal for those seeking an economical alternative to new parts without compromising quality and performance. With our water hose, you gain assurance that your vehicle will continue to operate efficiently and safely while avoiding unexpected expenses for costly repairs.

Often, the intake hose can suffer from wear over time due to exposure to heat and engine vibrations, leading to cracks or leaks. These issues can result in decreased engine performance and increased fuel consumption. It is advisable to inspect and, if necessary, replace the intake hose to ensure your vehicle operates at peak performance.

Replacing the Turbo Intake Hose is a straightforward process, generally seamless for both professional mechanics and DIY enthusiasts. It is typically recommended to replace this part during regular maintenance intervals or whenever any signs of wear are detected.

Technical Information

• Manufacturer: Citroën / Peugeot
• Model: 1.4 HDI
• Product Codes: 143445
• Other Numbers: Not specified

Are you looking for a reliable and cost-effective way to restore optimal air intake functionality in your Citroën or Peugeot vehicle? Our used Air Intake Hose for 1.5 HDI engines from Citroën and Peugeot (part number 9810958280) is the perfect choice for any mechanic or DIY enthusiast striving to keep their vehicle in excellent condition without excessively high replacement part costs.

The air intake hose is critical for the proper functioning of the engine, as it ensures that clean and optimized air is delivered to the combustion chamber, necessary for efficient fuel combustion. In practice, this means better engine performance, lower fuel consumption, and reduced emissions. The used hose we offer represents a cost-effective solution for restoring these essential functions.

Technical Information:
Manufacturer: Citroën, Peugeot
Model: Designed for Citroën Berlingo III, Fiat Doblo III, Opel Combo E K9, Peugeot Rifter, Toyota ProAce City
Product Codes: 9810958280
Other Numbers: This part may appear under various numbers depending on the specific vehicle model and production year.

If you are working on repair or maintenance of Citroën or Peugeot vehicles, this air intake hose might be exactly what you need to ensure optimal engine performance. Our part is already verified and ready for installation, saving you time and potential worries about compatibility and functionality. Remember, the proper functioning of the air intake system is essential for the long-term and reliable operation of your vehicle.

Take advantage of our offer and secure a quality replacement part that will extend your engine’s lifespan and enhance your vehicle’s overall performance. Order now, as the availability of these used parts may be limited!