This alternator bracket is a direct-fit mounting component designed for Citroën and Peugeot models equipped with the 1.6 HDi diesel engine. It secures the alternator to the engine block, maintains correct belt alignment and tensioner geometry, and ensures reliable charging system operation. The part is commonly searched by OE references 9658199380 and 5706L1, so include these codes when looking up fitment or ordering.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2; Citroën C3; Citroën C3 Pluriel; Citroën C4; Peugeot 1007; Peugeot 307 – Primarily 1.6 HDi engine applications
• Product Codes: 9658199380, 5706L1
• Additional Numbers: Fitment references and category tags: 1.6 HDi (associated listings may also reference 2.0 HDi / 2.2 HDi in some applications)

Compatibility And Fitment Notes

Intended for use on Citroën and Peugeot models fitted with the 1.6 HDi engine family. Always check the vehicle model year and engine code when comparing part numbers. The OE references 9658199380 and 5706L1 are the most common identifiers used by workshops and spare-parts databases.

Replacement Procedure

• Park the vehicle on a level surface, set the handbrake and isolate the battery.
• Loosen the accessory drive belt by releasing the tensioner and remove the belt from the alternator pulley.
• Disconnect the alternator electrical connectors and, if required, remove the alternator to gain access to the bracket.
• Support the alternator and remove the mounting bolts securing the bracket to the cylinder head/block.
• Fit the new bracket in position, start bolts by hand, then tighten to the manufacturer’s torque specifications.
• Reinstall the alternator, reconnect electrical connections, refit the drive belt and set the correct belt tension.
• Reconnect the battery and verify charging system operation at idle and under load.

Installation Recommendations

• Always isolate the battery before starting work and follow manufacturer safety procedures.
• Use proper tools to release and set belt tension; avoid forcing or bending the alternator housing.
• Replace any corroded or damaged fasteners and apply threadlocker where recommended by the vehicle manufacturer.
• Tighten mounting bolts to the maker’s torque values; if unavailable, consult repair manuals or official service documentation.
• After installation, inspect belt alignment and run the engine to check for abnormal noises or vibration.

Why This Part Most Often Fails

Alternator brackets typically fail due to corrosion and metal fatigue after years of exposure to road salt and moisture, or because of mechanical stress from engine movement when other mounts or silentblocks are worn. Broken or seized mounting bolts, damage from improper belt tensioning, and impact from road debris can also lead to failure. Failure symptoms include misaligned drive belt, belt squeal, alternator movement, charging faults or visible cracks in the bracket.

Practical Tips For Workshops And DIY Mechanics

• When replacing the bracket, inspect adjacent components: alternator bearings, belt condition, tensioner, and engine mounts (silentblocks).
• Keep the OE product codes 9658199380 and 5706L1 in job notes to simplify future ordering and parts lookup.
• If threads in the cylinder head are damaged, address the repair before fitting the new bracket to avoid repeat failures.

Keywords For Search And Ordering

Alternator Bracket, Citroën Alternator Mount, Peugeot Alternator Mount, 1.6 HDi Alternator Bracket, OE 9658199380, 5706L1, Alternator Mounting Bracket

This alternator bracket is a direct-fit replacement designed for a range of Citroën and Peugeot models equipped with the 1.6 HDi engine. Supplied with the common OEM reference numbers, this robust mounting bracket restores correct alternator positioning and belt alignment, helping to eliminate charging-system faults, belt noise and premature wear. Ideal for professional workshops and DIY mechanics who need a reliable replacement part identified by OE codes.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2, Citroën C3, Citroën C3 Pluriel, Citroën C4, Peugeot 1007, Peugeot 307
• Product Codes: 9656125280, 9804120780
• Additional Numbers: 5706K9

Function And Symptoms

The bracket secures the alternator to the engine block and ensures correct alignment of the accessory drive belt. When the bracket is damaged or loose, common symptoms include belt squeal, irregular charging voltage, visible misalignment of the alternator pulley and increased vibration or noise from the front of the engine. Addressing a faulty bracket promptly prevents secondary damage to the alternator, belt, tensioner and pulleys.

Replacement Procedure

Recommended for experienced mechanics or competent DIYers with basic tools. Typical replacement steps:

• Park the vehicle on a level surface, engage the parking brake and disconnect the negative battery terminal.
• Relieve tension from the drive belt and remove the belt from the alternator pulley.
• Support the alternator (with a jack or strap) to prevent it from dropping when the bracket is removed.
• Remove mounting bolts securing the alternator and the bracket to the engine block. Inspect bolts and replace if corroded or stretched.
• Fit the new bracket, align the alternator, tighten mounting bolts to the manufacturer’s torque specifications and reinstall the drive belt, ensuring correct tension and pulley alignment.
• Reconnect the battery, start the engine and verify charging system voltage and absence of abnormal noises.

Installation Recommendations

• Always Disconnect The Battery Before Starting Work To Avoid Short Circuits.
• Inspect The Alternator, Belt, Tensioner And Pulleys While Replacing The Bracket; Replace Any Worn Components To Avoid Recurring Failures.
• Use New Fasteners If Originals Are Corroded Or Damaged. Apply Correct Torque Values From The Vehicle Manufacturer.
• Check Belt Alignment Carefully After Installation; Misalignment Shortens Belt And Alternator Bearing Life.

Why The Part Fails Most Often

• Corrosion And Rust: Exposure To Road Salt And Moisture Can Weaken The Bracket Over Time.
• Fatigue And Cracking: Continuous Vibration From The Engine Or A Stressed Mount Can Cause Cracks Or Breakage.
• Impact Damage: Front-End Impacts Or Road Debris Can Bend Or Fracture The Bracket.
• Related Component Failure: A Seized Tensioner Or Misaligned Pulley Places Extra Load On The Bracket, Leading To Premature Failure.

This part is commonly referenced by OE numbers 9656125280, 9804120780 and reference 5706K9. When searching or ordering, using these codes will help you find the correct alternator bracket for the listed Citroën and Peugeot models with the 1.6 HDi engine.

Reliable alternator bracket designed for Citroën and Peugeot HDi engines, ensuring secure mounting and correct alignment of the alternator. This direct-fit bracket is commonly searched under the OEM numbers 9655652980 and 5706K3, which makes it easy to find in parts catalogs. Built to restore correct belt routing and reduce vibration transmission, it is an essential replacement part for charging system reliability. Ideal for professional workshops and experienced DIY mechanics working on 1.6 HDi powertrains.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2; Citroën C3; Citroën C3 Pluriel; Citroën C4; Citroën C4 Picasso; Peugeot 1007; Peugeot 3008 I; Peugeot 307; Peugeot 308; Peugeot 407 (primarily 1.6 HDi applications)
• Product Codes: 9655652980, 5706K3
• Additional Numbers: 9655652980 / 5706K3

Function And Application

The alternator bracket secures the alternator to the engine block and maintains correct pulley alignment for the accessory belt. Proper function prevents premature belt wear, noise, and charging system faults. It is typically used on 1.6 HDi diesel engines in the listed Citroën and Peugeot models and may share mounting points with related HDi variants.

How To Replace

Basic replacement overview for experienced technicians:

• Disconnect the negative battery terminal before starting work.
• Support the engine with a suitable jack and block under the oil pan or use an engine support bar.
• Release belt tension and remove the accessory belt or move the alternator to relieve tension.
• Remove any components blocking access to the bracket, such as the alternator or intake covers.
• Unbolt the old bracket from the engine block and remove it together with any associated spacers or bushings.
• Fit the new bracket, reuse or replace mounting hardware as recommended, and tighten bolts to the manufacturer’s torque specifications.
• Refit the alternator, restore belt tension, reconnect the battery and verify correct belt alignment and charging system operation.

Installation Recommendations

• Always Disconnect The Battery Before Work To Avoid Short Circuits And Unwanted Electrical Damage.
• Inspect The Alternator Pulley, Belt, Tensioner And Nearby Engine Mounts When Replacing The Bracket; Worn Components Accelerate Failure.
• Use Proper Torque Values From The Service Manual For All Fasteners To Prevent Loosening Or Thread Damage.
• Replace Damaged Or Corroded Bolts And Washers; Where Applicable Apply Threadlocker According To Manufacturer Instructions.

Why This Part Fails

• Corrosion And Rust From Road Salt And Moisture Can Reduce Structural Integrity.
• Fatigue Cracks Due To Continuous Engine Vibrations And High Torque Loads Over Time.
• Impact Damage From Accidents Or Improper Lifting/Support During Engine Service.
• Indirect Damage Caused By A Failed Engine Mount Or Excessive Belt Tension Which Transfers Additional Stress To The Bracket.

Compatibility And Search Tips

Search by OEM part numbers 9655652980 or 5706K3 for fastest match. Also check fitment against vehicle model and 1.6 HDi engine designation to ensure correct application.

Safety Note

Work Should Be Performed By Qualified Personnel Or Experienced Mechanics. Use Appropriate Lifting Equipment And Follow Vehicle Manufacturer Procedures To Avoid Injury Or Damage.

This alternator bracket is designed for the 1.6 HDi EURO5 engines used in a range of Citroën and Peugeot models. Built to restore correct alignment and secure mounting of the alternator, it helps eliminate belt misalignment, reduce bearing load and prevent premature alternator wear. The part matches OEM fitment and is commonly referenced by the part numbers 9684613880 and 5706N9, so it is often searched by mechanics and DIYers using those codes.

Key Features and Benefits

• Direct replacement for OE mounting points on 1.6 HDi EURO5 engines.
• Restores correct alternator alignment, reducing belt wear and alternator bearing stress.
• Durable construction to withstand engine vibrations and thermal cycles.
• Compatible with commonly affected Citroën and Peugeot platforms — ideal for garage fitment and independent repairs.
• Often identified in searches by part numbers 9684613880 and 5706N9.

Technical Information

• Manufacturer: Stellantis
• Model: Citroën Berlingo B9, Citroën C4 II, Citroën C4 Picasso, Citroën C5 X7, Peugeot 3008 I, Peugeot 308, Peugeot Partner Tepee
• Product Codes: 9684613880, 5706N9
• Other Numbers: —

Installation Recommendations

Professional installation is recommended for correct alignment and safety. Typical replacement steps:

• Disconnect the battery before starting work.
• Relieve tension on the accessory belt and remove the belt from the alternator pulley.
• Support the alternator (use a jack or support strap) and remove alternator mounting bolts.
• Remove the old bracket and compare mounting points and bolt lengths. Note: Bolts shown in pictures may not be supplied with the part.
• Fit the new bracket, mount the alternator, and tighten fasteners to the manufacturer’s torque specifications.
• Refit the belt, check alignment, reconnect the battery and verify charging system operation.

Always follow the vehicle manufacturer’s procedure and torque settings. If threads are damaged, repair or replace fasteners before final assembly.

Why This Part Fails Most Often

• Corrosion: Exposure to road salt and moisture can corrode mounting points and fasteners, weakening the bracket.
• Fatigue Cracking: Long-term vibration and cyclic loads may cause cracks or broken mounting ears.
• Impact Damage: Front-end impacts or engine/transmission movement from a collision can deform or break the bracket.
• Stripped Threads Or Incorrect Fasteners: Over-torquing or cross-threaded bolts compromise secure mounting.
• Associated Component Wear: Worn engine mounts or a misaligned belt system increase stress on the bracket and can lead to premature failure.

Notes For Buyers

This part is commonly searched by its OEM numbers 9684613880 and 5706N9. Before purchase, verify that the bracket corresponds to the 1.6 HDi EURO5 engine layout on your specific Citroën or Peugeot model and have replacement fasteners ready if needed.

Recommended For

Independent mechanics and DIY enthusiasts performing alternator or belt-system repairs on Citroën and Peugeot 1.6 HDi EURO5 models who require an OE-compatible alternator mounting solution.

High-quality replacement mounting bracket designed for the 2.0 HDi RH02 engine to secure the air conditioning compressor and alternator. Ideal for professional workshops and DIY mechanics who need a reliable, OE-compatible bracket that restores correct alignment and belt tension. Frequently searched by part numbers 9688628680 and 5706N7, this bracket improves engine accessory stability, reduces vibration and prevents premature wear of belts and pulleys.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: 2.0 HDi RH02
• Product Codes: 9688628680, 5706N7
• Additional Numbers: NFP
• Compatible Vehicles: Citroën C4 Picasso; Citroën C5 (X7); Citroën C8; DS4; DS5; Peugeot 3008 I; Peugeot 308; Peugeot 407; Peugeot 807; Peugeot 508

How It Is Replaced

Replacement requires basic workshop tools and some experience with engine accessory removal. Typical procedure:

1. Park on level ground, engage handbrake and support the vehicle securely on axle stands.
2. Disconnect the negative battery terminal to avoid accidental short circuits when working near the alternator.
3. Relieve belt tension and remove drive belts (serpentine/accessory belts) to gain access to the bracket.
4. Support the compressor and alternator (or remove them from the bracket) so they do not hang on hoses or wiring.
5. Unbolt the old bracket from the engine block and remove. Inspect mating surfaces and fasteners for corrosion or damage.
6. Fit the new bracket, tighten bolts to manufacturer torque specifications, and reinstall compressor/alternator and belts. Replace any damaged fasteners or worn belt tensioners.
7. Start the engine and verify correct belt alignment, tension and absence of unusual vibration or noise.

Installation Recommendations

• Use Correct Torque: Always tighten mounting bolts to the manufacturer’s torque settings to avoid deformation or premature loosening.
• Inspect Related Parts: Replace worn belts, tensioners, pulleys and any corroded fasteners while replacing the bracket to ensure a long-lasting repair.
• Transfer Components Carefully: If transferring compressor or alternator between brackets, support electrical connectors and refrigerant lines to avoid damage.
• Clean Mating Surfaces: Remove rust and debris from engine block mounting points to ensure full contact and correct alignment.
• Professional Tools: Use an engine support or jack with a protective pad when supporting engine accessories to prevent damage to oil pan or components.

Why This Part Most Often Fails

• Corrosion And Rust: Road salt and moisture accelerate metal corrosion, weakening the bracket and mounting points.
• Mechanical Fatigue: Long-term vibration and cyclical loads from the engine can cause cracks or deformation.
• Impact Or Accident Damage: Front-end impacts can bend or break the bracket or its mounts.
• Worn Ancillary Components: Failed tensioners or misaligned pulleys increase stress on the bracket and accelerate wear.
• Improper Installation: Loose bolts or incorrect torque can lead to movement, fatigue and eventual failure.

This alternator bracket is a direct-fit replacement designed for 1.6 HDi 16V engines used in various Citroën and Peugeot models. Supplied with OE references 9659200880 and 5706N6, the bracket restores correct alternator position and belt alignment, helping to eliminate belt squeal, premature belt wear and charging irregularities. Built for professional workshops and experienced DIY mechanics, this part is a practical solution when the original mounting point is corroded, cracked or otherwise damaged.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: 1.6 HDi 16V – Citroën C4, Citroën C4 Picasso, Citroën C5, Citroën C5 X7, Peugeot 207, Peugeot 3008 I, Peugeot 307, Peugeot 407
• Product Codes: 9659200880, 5706N6
• Additional Numbers: NFP

Function And Benefits

The alternator bracket secures the alternator to the engine block, maintaining correct alignment with the drive belt and tensioner. A rigid, correctly positioned bracket ensures even belt tension, reduces bearing loads on the alternator and prevents vibration-related wear. Replacing a worn or damaged bracket restores optimal belt routing and charging system reliability.

How To Replace (Overview)

Replacement requires moderate mechanical skill and basic tools. Typical procedure:

• Park vehicle on level ground, engage handbrake and disconnect the negative battery terminal.
• Release belt tension via the tensioner and remove the drive belt from the alternator pulley.
• Support the alternator (jack or strap), disconnect electrical connections and the main power cable.
• Remove alternator mounting bolts and the old bracket. Transfer any spacers or bushings if present.
• Fit the new bracket, loosely install mounting bolts, align the alternator, then torque bolts to the manufacturer’s specification.
• Reinstall the drive belt, set correct belt tension, reconnect electricals and the battery, then verify charging system operation at idle and under load.

Installation Recommendation

Always follow safety procedures: disconnect the negative battery terminal before starting work and support the alternator to avoid strain on electrical connections. Inspect related components (belt, tensioner, alternator mounting bolts, electrical terminals) and replace any worn parts at the same time. Use proper torque values from the vehicle repair manual when tightening mounting bolts to avoid distortion or future loosening.

Most Common Reasons For Failure

• Corrosion And Rust: Long-term exposure to moisture and road salt can weaken mounting points and cause cracks.
• Mechanical Damage: Impacts, engine knocks or improper lifting/support during repairs can bend or fracture the bracket.
• Fatigue And Vibration: Repeated engine vibration or a misaligned belt places extra stress on the bracket and bushings.
• Worn Bushings Or Fasteners: Deteriorated rubber mounts or loose/overstressed bolts lead to movement and accelerated wear.
• Related Component Failure: Failing alternator bearings or seized pulleys transfer additional loads to the bracket, causing damage over time.

When To Replace

There is no fixed interval for replacement. Inspect the bracket whenever you replace the alternator or if you observe symptoms such as belt noise, uneven belt wear, visible cracks or movement at the mounting point, or charging system faults. Proactive replacement is recommended when corrosion or physical damage is evident.

Compatibility And Notes

Compatible with 1.6 HDi 16V engine variants in the listed Citroën and Peugeot models. Always ensure the OE numbers 9659200880 and 5706N6 match the part required for your application. This bracket is intended as a mechanical replacement part; inspect and service the belt and tensioner together for a reliable repair.

This alternator bracket is designed for 1.6 HDi 16V engines used in various Citroën and Peugeot models. Ideal for professional workshops and experienced DIY mechanics, the bracket ensures correct alignment and secure mounting of the alternator to maintain charging system reliability. Frequently searched by OEM numbers, this part is a direct-fit solution that helps restore belt alignment and eliminates vibration-related charging faults.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C5 (X7), Peugeot 407 — 1.6 HDi 16V
• Product Codes: 9658199180, 5706L3
• Additional Numbers: NFP

Function And Application

The alternator bracket secures the alternator to the engine block and maintains precise belt routing and tension. Proper mounting prevents misalignment that can cause premature belt wear, noise, or alternator bearing damage. On certain variants the bracket also acts as a support point that dampens vibration; some designs incorporate rubber inserts to absorb engine movement.

Compatible Models

Typical fitment includes Citroën C5 (X7) and Peugeot 407 with the 1.6 HDi 16V engine. Always verify the part number printed on the original bracket — common reference numbers for this item are 9658199180 and 5706L3.

Replacement And Installation Recommendations

Recommended basic procedure for replacement (for experienced mechanics/DIY):

• Disconnect the negative battery terminal to avoid electrical short.
• Loosen and remove the accessory drive belt or use a suitable belt tensioner tool to release tension.
• Support the alternator and disconnect electrical connectors and wiring harness.
• Unbolt the alternator from the bracket, then remove the bracket mounting bolts from the engine block.
• Fit the new bracket, tighten mounting bolts evenly, reattach the alternator, reconnect electrical connections and refit the belt to correct tension.
• Check belt alignment and system operation after starting the engine.

Avoid forcing seized bolts; apply penetrating lubricant and use correct sockets to prevent rounding. If the bracket attaches near or under other components, slight additional disassembly may be required. Use proper safety supports if the engine position needs to be held during work. If unsure about torque values for specific bolts, consult the vehicle service manual.

Why This Part Commonly Fails

Common causes of alternator bracket failure include corrosion from road salt and moisture, metal fatigue from long-term vibration, impact damage from collisions, and deterioration of any rubber mounting inserts that reduce damping. Failures lead to alternator misalignment, belt squeal, accelerated belt wear, or alternator bearing overload — all of which can cause charging faults or electrical issues.

Practical Tips For Mechanics And DIY

• Inspect surrounding components (belt, tensioner, alternator bearings) when replacing the bracket to avoid repeat repairs.
• Replace bolts that show corrosion or thread damage; reuse only bolts in good condition.
• Perform a visual and functional check after installation: belt tracking, absence of unusual noise, and stable charging voltage at idle and under load.
• Searching by part number (e.g., 9658199180 or 5706L3) often yields the fastest match for compatibility.

This alternator bracket is a practical spare for workshops and skilled DIYers looking to restore proper charging system function on Citroën and Peugeot 1.6 HDi 16V engines. Correct fitment and careful installation significantly reduce the risk of secondary damage to belts and charging components.

Direct-fit alternator mount for 1.4 HDi 16V engines used on Citroën and Peugeot models. Supplied under OEM references 9646424380 and 5706G3, this bracket secures the alternator to the engine block and restores correct belt alignment and tension. Ideal for professional workshops and DIY mechanics who need a reliable replacement part that matches factory geometry and mounting points.

This alternator mount is designed to deliver a solid, vibration-resistant connection between the alternator and engine. Replacing a worn or damaged bracket eliminates excessive alternator movement, reduces belt wear, and prevents premature failure of the alternator bearings and drive components. The part is compatible with common applications of the 1.4 HDi 16V family and is frequently searched by OEM part number, making it easy to find when ordering.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C3; Peugeot 1007 — 1.4 HDi 16V Applications
• Product Codes: 9646424380, 5706G3
• Additional Numbers: None Listed

Installation Recommendations

Always Disconnect The Battery Before Starting Work. Support The Alternator Or Engine As Required To Remove Load From The Bracket. Typical Replacement Steps:

• Loosen and remove the drive belt (release the belt tensioner where fitted).
• Support the alternator to prevent it dropping when unbolted.
• Remove the mounting bolts securing the alternator bracket to the engine block.
• Inspect mating surfaces and fasteners; clean threads and check for damage.
• Fit the new bracket, align the alternator and hand-tighten bolts before torquing to manufacturer specifications.
• Reinstall the belt, set correct tension, reconnect the battery and verify charging system operation.

Use New Fasteners If Original Bolts Are Corroded Or Damaged. Follow Manufacturer Torque Specifications And Procedures To Avoid Thread Stripping Or Misalignment.

Why This Part Fails Most Often

• Corrosion And Rust: Exposure To Moisture And Road Salt Can Cause Metal Fatigue And Localized Weakening.
• Vibration And Fatigue Cracks: Continuous Engine And Accessory Vibration Leads To Crack Initiation Over Years Of Service.
• Seized Or Damaged Fasteners: Frozen Bolts Can Shear During Removal Or Prevent Proper Clamping Force.
• Impact Or Collision Damage: Front-End Impacts And Engine Bay Hits Can Bend Or Break The Bracket.
• Indirect Causes: Worn Engine Mounts Or Misaligned Accessories Increase Load On The Bracket And Accelerate Wear.

Fitment And Notes

Fits 1.4 HDi 16V Engines Commonly Found On Citroën C3 And Peugeot 1007. Frequently Identified By OEM Numbers 9646424380 And 5706G3 — Search By These Codes For Fast Identification. No Specific Replacement Interval; Inspect During Timing Belt/Service Intervals Or If You Notice Belt Misalignment, Unusual Noise, Or Alternator Movement.

Recommendation

For Best Results, Replace Any Corroded Or Damaged Fasteners And Check Associated Components (Belt, Tensioner, Alternator Bearings) At The Same Time. If You Are Unsure About Access Or Correct Torque Values, Seek Professional Installation To Ensure Long-Term Reliability.

Ensuring optimal function and long-term durability of your vehicle is crucial. Our used engine mount, specifically designed for 1.2 THP engines, delivers exactly that. This part is ideal for Citroën and Peugeot car owners who seek a quality and reliable solution to keep their engine securely and stably positioned.

This engine mount was carefully removed from a functional vehicle and is ready for reuse. Its primary role is to absorb vibrations and engine movements, enhancing driving comfort and reducing wear on other engine components. Due to its durability and structural properties, this part offers a long-lasting, dependable solution.

Technical Information:

Manufacturer: Citroën, Peugeot
Model: Citroën C4 II, DS4
Product Codes: 9677258480, 9676523080
Additional Numbers: Not available

When replacing this part, it is recommended to have the installation performed by an authorized service center or under the supervision of an experienced mechanic to ensure correct fitting and functionality. For further information on compatibility or installation, please do not hesitate to contact our customer support.

The engine mount absorbs and dampens vibrations from the engine to the body of the car, preventing noise and reducing mechanical wear. Regular inspection and replacement are essential especially if you notice increased engine vibrations, unusual noises, or damage from previous impacts or accidents. Proper maintenance of this component ensures the longevity of the engine and contributes to a smooth driving experience.

Technical Information

• Manufacturer: PSA, Citroën, Peugeot
• Compatible Models: Citroën C4, Citroën C4 Picasso, Citroën C5 II, Citroën C5 III, Peugeot 307, Peugeot 407, Peugeot 508
• Product Codes: 9647029580, 1839C8
• Additional Numbers: NFP (New Factory Part)

This engine mount is crafted to meet the original specifications, offering reliability and maintaining engine alignment and stability. Installation should be performed by a qualified mechanic to ensure correct fitment and performance. Choosing this engine mount guarantees your vehicle’s powertrain is securely supported, reducing stress on other components and improving overall driving stability.

Prioritizing quality, durability, and function, this right engine mount provides an efficient replacement for OEM parts at an affordable price. Keep your engine securely mounted and enjoy quieter, more comfortable rides with this reliable engine mount tailored for Citroën and Peugeot vehicles.