Overview

This RHS Engine Cover Is An Original-Fit Part For The 2.0 HDI Engine Found On The Peugeot 307. It Protects The Top Of The Engine, Helps Manage Underbonnet Airflow, Reduces Noise And Shields Wiring And Hoses From Dirt And Heat. Typical Search Terms: Engine Cover 2.0 HDI, RHS Engine Cover, Peugeot 307 Engine Cover, OEM 9634754680.

Key Benefits

• Direct Fit For Peugeot 307 2.0 HDI — Matches OEM Mounting Points.
• Protects Engine Components From Debris And Fluid Splash.
• Improves Underbonnet Appearance And Noise Dampening.
• Supplied With Original Reference Numbers For Easy Identification.

Application

Designed Specifically For Peugeot 307 Models Equipped With The 2.0 HDI Engine. Use The Listed Product Codes To Confirm Fitment: 9634754680, 013739. Cross-Reference Number: 9653447480.

Replacement Procedure

1. Allow The Engine To Cool To Avoid Burns And To Prevent Warping Of Plastic Components.
2. Remove Any Retaining Clips Or Screws Securing The Old Cover. Keep Fasteners If They Are Undamaged; Replace Broken Clips.
3. Carefully Lift The Cover Off, Releasing Any Tabs Or Grommets. Disconnect Any Attached Hoses Or Small Trim Pieces If Present.
4. Inspect Mounting Points, Gaskets And Nearby Hoses For Damage Or Oil Contamination; Clean The Area Before Fitting The New Cover.
5. Fit The Replacement Cover Aligning All Mounting Tabs, Then Reinstall Clips/Screws Without Over-Tightening.
6. Start The Engine And Check For Rattles Or Contact With Moving Parts. Recheck Fasteners After A Short Test Drive.

Technical Information

• Manufacturer: Stellantis
• Model: Peugeot 307 (2.0 HDI)
• Product Codes: 9634754680; 013739
• Other Numbers: 9653447480

Installation Recommendations

Use The Correct Replacement Clips And Fasteners To Ensure Secure Mounting And Eliminate Vibrations. Inspect Surrounding Components — Oil Leaks Or Loose Hoses Can Accelerate Wear Or Cause The Cover To Degrade. If Plastic Mounting Tabs Are Broken, Replace Them Or Use Repair Kits Before Installing The New Cover. For Professional Fits, Work In A Clean, Well-Lit Area And Use Trim Tools To Avoid Damaging Adjacent Panels.

Most Common Failure Reasons

• Cracked Or Broken Plastic Due To Heat Cycling And Engine Vibration Over Time.
• Impact Damage From Road Debris Or Improper Removal/Installation.
• Degraded Mounting Tabs Leading To Rattles Or Partial Detachment.
• Oil Or Coolant Contamination That Softens Or Discolors The Cover.

Notes For Mechanics And DIYers

This Part Is A Practical Replacement When The Existing Engine Cover Is Damaged, Missing Mounting Points, Or No Longer Provides Adequate Protection. Keep The OEM Reference Numbers Handy When Searching Or Ordering To Ensure Fast And Accurate Identification.

This engine cover is a direct-fit component designed for 2.0i 16V RFK engines with 130 kW output in selected Citroën and Peugeot models. It protects the top of the engine from dirt and debris, helps reduce engine noise, and provides a tidy appearance under the bonnet. The cover corresponds to common part numbers used by Stellantis groups for these models and is aimed at professional mechanics and experienced DIY enthusiasts who need a reliable replacement that restores factory fit and function.

Designed for workshop efficiency and SEO-friendly searches by part number, this cover is a practical choice when servicing Citroën C4 or Peugeot 206 RC / 307 CC vehicles with the 2.0i 16V RFK engine. It is typically mounted with rubber grommets and plastic clips or a small number of screws, making removal and reinstallation quick during routine maintenance or engine work. Keeping the cover in good condition helps maintain under-bonnet insulation and prevents small components from becoming contaminated by oil spray or road grime.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4; Peugeot 206 RC; Peugeot 307 CC — Engine: 2.0i 16V RFK (130 kW)
• Product Codes: 9655202180, 963936480
• Additional Numbers: 0248L5, 025084, 25084

Installation Recommendation

Remove any cosmetic engine covers or trim obstructing access, then unclip or unscrew the old cover starting from the rear clips and working forward to avoid bending tabs. Inspect rubber grommets and plastic fasteners and replace any that are cracked or deformed—worn mounts are the most common cause of rattles after fitting. Align the replacement cover over the mounting points and press down evenly until all grommets click into place, or reinstall screws to the manufacturer’s recommended snugness (do not overtighten plastic fasteners). After installation, start the engine and listen for unusual rattles; recheck fasteners after a short test drive.

Why The Part Most Commonly Fails

Engine covers typically fail due to age-related material degradation and mechanical damage. Constant exposure to heat cycles, oil and chemical contamination, and vibration makes plastic covers brittle over time. The most frequent failure modes are broken mounting tabs, cracked plastic, and deteriorated rubber mounts. Impact from tools during maintenance or from debris on rough roads can also cause cracks or misalignment. Replacing damaged clips and grommets at the same time as the cover significantly reduces the chance of noise or poor fitment after installation.

Suitable for mechanics and competent DIYers searching by part number or model fitment, this cover restores proper protection and appearance to the engine bay of compatible Citroën and Peugeot vehicles. Check the listed product and additional numbers against your reference to ensure compatibility with your specific engine variant.

This replacement engine cover is designed for 1.6 HDi diesel engines (55, 66 and 80 kW) used across a range of Citroën and Peugeot models. Supplied to match OE reference numbers commonly searched by mechanics (9659999980, 0137E5), the cover restores the engine bay appearance, protects critical components from dirt and debris, and helps reduce perceived engine noise. Ideal for professional workshops and DIY enthusiasts who want a direct-fit part that follows original mounting points and fitment characteristics.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën Berlingo, Citroën Berlingo B9, Citroën C3, Citroën C3 Picasso, Citroën C4, Citroën C4 Picasso, Citroën C5, Citroën Xsara Picasso, Peugeot 206, Peugeot 207, Peugeot 307, Peugeot 308, Peugeot 407, Peugeot Partner, Peugeot Partner Tepee
• Product Codes: 9659999980, 0137E5
• Additional Numbers: 13700000

Fitment Notes

The cover is intended for 1.6 HDi engines rated at 55, 66 or 80 kW. It fits vehicles that use the same engine cover mounting configuration and OE references listed above. Many customers search by the OE part numbers (9659999980, 0137E5), so these references are included for quick identification.

Installation Recommendations

• Work On A Cold Engine: Allow The Engine To Cool Before Starting To Avoid Burns And Warping Of Plastic Components.
• Remove Fasteners Carefully: Release Retaining Clips And Screws In Sequence To Avoid Breaking Mounting Points. Use Trim Tools Where Appropriate.
• Inspect Mounting Points: Check For Damaged Clips Or Broken Pins And Replace Them If Necessary To Ensure A Secure Fit.
• Re-Fit With Care: Align The Cover Over Mounts And Fasten By Hand Before Final Tightening. Avoid Over-Torquing Plastic Fixings.
• Check For Leaks And Loose Hoses: While The Cover Is Off, Inspect Surrounding Hoses, Wiring And Seals For Oil Or Coolant Leaks That May Cause Future Damage.

Why This Part Most Often Fails

Engine covers are subject to heat cycles, chemical contamination (oil or fuel spills) and mechanical stress from repeated removal. The most common failure modes are cracked or brittle plastic due to long-term heat exposure, broken mounting clips from improper removal, and deformation caused by localized oil or coolant leaks. Impact damage from road debris or minor collisions can also crack or dislodge the cover.

Part Numbers And Searches: This part is frequently searched using OE references 9659999980 and 0137E5—include these in your workshop order or online search to locate compatible replacements quickly.

The 2.0 HDI RHR Citroën engine cover is designed for cars with a 2.0 HDI diesel engine with the RHR designation and serves to protect the engine from dirt, water and mechanical damage from the underside of the car. At the same time, it helps improve airflow under the vehicle and can thus contribute to reduced noise and better aerodynamics. In workshops, this part is often in demand due to damage to the original cover due to impact, driving over bumps or corrosion of the attachment.

Technical information:
Manufacturer: PSA Citroën Peugeot
Model: Citroën (especially suitable for selected versions of the Citroën C5 with a 2.0 HDI RHR engine – depending on the specific equipment and year of manufacture)
Engine type: 2.0 HDI RHR (DW10BTED4)
Product codes: 9657955780, 013770, 0137A3
Other numbers: they may also appear in catalogs under PSA internal designations, or under secondary aftermarket supplier numbers

Features and benefits:
– Protection of the engine and the lower part of the aggregate from stones, gravel, salt and other dirt from the road
– Reduction of the risk of contamination of the engine compartment, wiring and hoses
– Reduction of noise from the engine and the lower part of the car
– Precise shaping for the given type of 2.0 HDI RHR engine for easy installation in original mounts

Installation recommendations:
Before assembly, check the condition of all mounting points on the chassis as well as the screws or plastic handles themselves – replace damaged or corroded elements so that the cover is firmly and securely attached. Carefully remove the old engine cover, clean the mating surfaces and make sure that no non-original chassis or exhaust modifications interfere with the mounting area. Apply the new part to the car gradually, first grasping the outermost screws or clips, only then tightening the rest. Tighten the screws evenly, without using excessive force to avoid cracking the plastic or stripping the threads. When working, we recommend using a workshop jack or properly secured mobile lifting arms, never work under the car only supported by the lifting arm itself. After installation, check that the cover does not rub anywhere on the exhaust, axle arms or wheels when driving at full speed, and after the first few kilometers of driving, visually check the tightness of the mounting again.

The 1.5 HDi engine cover is designed for modern PSA Stellantis and Toyota engines and serves as an upper plastic engine cover. It improves the aesthetics of the engine compartment, dampens engine noise and protects the upper part of the unit and the electrical installation from dirt, dust and small drops of liquids.

Manufacturer: PSA / CITROËN / PEUGEOT
Model: 1.5 HDi (BlueHDi) engine – according to specific application for Citroën, DS, Fiat, Opel, Peugeot, Toyota brands
Product codes: 9836650880
Other numbers: there may be slight variants of the suffixes depending on the year of manufacture and brand, but it is always essential to match the number 9836650880 stamped or printed directly on the part

This engine cover is used on cars with a 1.5 HDi/BlueHDi diesel engine, typically on models such as Citroën Berlingo III, Citroën C3 III, Citroën C4 II, Citroën C4 Picasso II, Peugeot 308 T9, Peugeot Partner III, Peugeot Rifter and related models from other brands (DS, Fiat, Opel, Toyota) equipped with the same engine. It is always a used original part from disassembly, which corresponds to the serial assembly in terms of shape and attachment.

The cover is designed to be attached to the top of the engine using plastic mounts or rubber silent blocks. A properly fitted cover limits the transmission of vibrations to the body, reduces noise in the cabin and helps keep the engine compartment clearer and cleaner, which will be appreciated by auto mechanics during subsequent repairs and servicing.

Installation recommendations:
– Before fitting, check that the part number 9836650880 is the same as the original cover from your car.
– Check the condition of the fixing pins, silent blocks and holders on the engine; replace damaged or missing elements so that the cover fits tightly and unwanted vibrations or noises do not occur.
– Before putting the cover on, clean the top of the engine of coarse dirt so that dust and oil do not accumulate under the cover.
– Fit the cover evenly from above, first align it according to the guide elements and then push it into the locking position on all handles with gentle hand pressure. Do not use brute force or prying tools to avoid damaging the plastic pawls or rubber mounts.
– After assembly, start the engine briefly and check that the cover does not rattle anywhere, does not touch rotating parts or high-temperature exhaust components.

Original engine cover for Citroën and Peugeot cars with 2.0 HDi engine. It is a lower plastic protective part that covers the space under the engine and gearbox. It protects the aggregate from water, salt and dirt from the road, reduces noise from the chassis and helps the aerodynamics of the car. Thanks to the original design with corresponding handles, it fits exactly on the specified models and keeps its shape even during longer use.

The manifestation of a damaged or missing cover is usually increased noise from the chassis, pollution of the engine compartment, broken or torn handles or vibrations while driving. Replacement is suitable for cracks after impact with retarders, curb or after driving in deeper water and snow. A properly fitted cover helps keep the motor in better condition and extends the life of the peripherals.

Assembly is usually solved with screws and plastic clips in longitudinal beams and undercarriage. We recommend that you raise the car safely, compare the shape and spacing of the mounts with the original part, and use new mounting clips/screws when installing if the originals are worn. Before assembly, check whether the undercarriage cover strips are missing – correct fixation of the cover often depends on them.

Compatibility is primarily determined by matching the part code. This cover is marked with OEM numbers 0137F0 and 9686165680, which are used as equivalents by PSA. Typically fitted to selected 2.0 HDi model versions: Citroën C5 X7 and Peugeot 3008 I, 308, 407, 5008 I. Before purchasing, always compare the part number and shape with your original cover or verify by VIN.

Technical information

• Manufacturer: PSA (Citroën/Peugeot), original part
• Model: selected versions with 2.0 HDi engine – e.g. Citroën C5 X7; Peugeot 3008 I, 308, 407, 5008 I (verify by VIN/part code)
• Product codes: 0137F0, 9686165680
• Other numbers: 0137.F0; 96,861,656 80

Assembly tip: clean the mating surfaces and replace missing fasteners. A properly tightened cover eliminates resonances and prevents re-damage.

The original bottom engine cover for 2.2 HDI (engine code 4HN) protects the aggregate and auxiliary systems from water, salt, gravel and dirt, while reducing air resistance and air resistance. It is a part of the production of PSA, which is now kept as NFP (no longer produced), so the quality piece used is the ideal choice for reliable repair.

Compatible especially with Citroen C-Crosser 2.2 HDI and Peugeot 4007 2.2 HDI. Parts with OE codes 9682121680, 9682120380 and 0137A1 are replaced by each other, it is the same version of the cover. If you are looking for a specific number, check it according to the label on the old part or in the car documentation – avoid incompatibility.

Functions and advantages: The lower engine cover prevents water from penetrating the belts, alternator and electric connectors, extending their life. It also prevents the engine compartment pollution and improves air flow under the car. Typical causes of damage are the impact of the retarder or curb, cracks from frost and missing fastening clips that allow the cover to vibrate and then break.

Mounting tips: Raise the car safely, remove the remaining clips/bolts of the old cover and clean the bearing surface. Install the new cover first – catch it in the extreme handles, compare it with the bumper and plastic wheel arches, and then fill the remaining screws and clips. Tighten evenly with a sense to prevent the plastic to burst. Use original or quality replacement of fasteners; Missing or rusty fasteners are a common cause of re -damage.

Status and origin: used original part of the dog (Citroen/Peugeot). It can carry common signs of use (abrasions) that do not affect the function. Before assembly, we recommend checking all handles and possibly add new clips/screws – often not included.

technical information

• Manufacturer: PSA (Citroen/Peugeot)
• Model: Citroen C-Crosser 2.2 HDI (4HN), Peugeot 4007 2.2 HDI (4Hn)
• product codes: 0137A1
• Other numbers: 9682121680, 9682120380, NFP

How to verify compatibility: Compare the shape and location of the fasteners according to the photos and confirm the match with any of the OE codes. If you are unsure, come out of the VIN and the 2.2 HDI engine with a 4HN code used for C-Crosser and 4007.

This engine cover is designed for 1.6 HDi diesel engines and provides reliable protection for the top of the engine while improving under-hood appearance and reducing noise. Ideal for professional mechanics and DIY enthusiasts, the part is commonly searched by its product numbers and fits a range of Peugeot models with 1.6 HDi engines. Replacing a damaged or missing engine cover restores proper protection of wiring, fuel lines and other vulnerable components and helps maintain tidy engine bay routing during repairs and inspections.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: 1.6 HDi (55 kW, 66 kW, 80 kW)
• Product Codes: 9659999880, 0137E5
• Other Numbers: 13700000
• Compatible Vehicles: Peugeot 207, 307, 308, 407, Partner (vehicles equipped with 1.6 HDi engines)

Function and Benefits

The engine cover protects the upper engine area from dirt, debris and accidental contact with hot components. It also contributes to noise damping and keeps hoses and wiring secured and routed away from moving parts. A correctly fitted cover prevents premature wear of peripheral components and improves the visual presentation of the engine bay during service.

Recommended Installation

Installation is straightforward for a trained mechanic or competent DIYer. Typical steps:

• Allow the engine to cool. Remove the old cover by undoing visible bolts, screws or plastic clips.
• Inspect mounting points, rubber grommets and clips; replace any damaged fasteners before fitting the new cover.
• Place the new cover into position, ensuring alignment of locating pins and grommets, then secure with the original fasteners. Do not overtighten plastic fixings.
• After installation, check for any contact with hoses or wiring and confirm there are no new rattles during a short test drive.

Common Failure Reasons

Engine covers typically fail due to impact damage (stone chips, collisions), heat ageing and embrittlement of plastic, or from broken mounting tabs and rubber grommets. Oil leaks or coolant leaks under the cover accelerate degradation and can cause warping or staining. Loose or missing fasteners often lead to vibration and noise, which is a frequent reason owners replace the cover.

This part is frequently searched by its product numbers (9659999880, 0137E5). If the cover shows cracks, deformed mounting points or significant discoloration from heat and fluids, replacement is recommended to preserve engine bay protection and reduce noise.

This replacement engine cover fits a range of Stellantis petrol engines and is a practical, OEM-fit option for professionals and DIY mechanics working on Citroën and Peugeot models. It protects top engine components, improves under-bonnet appearance and contributes to noise damping. Commonly searched by part numbers 9653373180, 9653425980 and 0248N4, this cover is ideal when original clips are broken, the cover is cracked or when you want to restore the engine bay look after maintenance.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C4, Citroën C4 Picasso, Citroën C5, Peugeot 307, Peugeot 407, Peugeot 3008 (I)
• Product Codes: 9653373180, 9653425980, 0248N4
• Additional Numbers: NFP (as listed)

Compatibility and Fitment

Designed for use with 1.8 16V (engine code 6FY) and 2.0 16V (engine code RFJ) petrol engines in the listed Citroën and Peugeot models. Always verify engine code and visual match to the existing cover before installation; the part numbers above are frequently used by customers when searching for correct fitment.

Function and Benefits

• Protects ignition coils, wiring and fuel/air components from dirt and mechanical damage.
• Reduces engine bay noise by providing an insulating barrier.
• Directs airflow and can help conceal oil stains or repairs for a cleaner appearance.
• OEM-style fit ensures correct mounting points and alignment with engine accessories.

Common Faults And Causes

Engine covers rarely fail structurally under normal conditions, but the most common issues are:

• Brittle or broken plastic clips and mounting points due to heat cycling and age.
• Cracks from impacts or improper removal (prying at incorrect points).
• Oil contamination leading to surface degradation or soiling; persistent oil leaks may indicate other engine faults that should be addressed.
• Warping caused by prolonged exposure to high under-bonnet temperatures.

Installation Recommendations

Recommended for mechanics and competent DIYers. Basic installation steps:

• Ensure the engine is switched off and cooled to touch.
• Remove existing retainers or screws securing the old cover; keep track of clips—replace any damaged grommets or fasteners.
• If the cover attaches to hoses, breather pipes or electrical connectors, carefully disconnect these before lifting the cover away.
• Place the new cover, align mounting points and secure with original or replacement fasteners. Replace brittle clips with new OEM-quality clips where possible for a secure fit.
• After installation, check that no hoses or wiring are trapped and start the engine to confirm there are no unusual noises or contact points.

Why Choose This Part

This engine cover is a practical, cost-effective way to restore the engine bay appearance and protect vital top-end components. Supplied to match common OEM references (9653373180, 9653425980, 0248N4), it’s a part often searched by mechanics and vehicle owners by number when servicing or repairing the listed Citroën and Peugeot models.

Technical Information
Manufacturer: PSA Citroën Peugeot
Model: RHR
Product Codes: 9657955780, 013770, 0137A3
Additional Numbers: 013770, 0137A3

The engine cover is essential for protecting the engine from external factors such as dirt, dust, or foreign objects that could enter the engine bay and cause damage or accelerated wear to engine components. This part is specifically engineered to ensure a perfect fit and maintain the engine’s proper function and performance. Replacing the engine cover is a relatively straightforward process that can be performed as part of routine vehicle maintenance.

Our used engine cover for the Peugeot 2.0 HDI RHR has been carefully selected and inspected to guarantee its quality and functionality. By maintaining high standards of quality and safety, we provide products that meet customer expectations while offering an economical solution for repair needs.

Choose our verified auto parts to ensure your vehicle remains operational and safe. With our extensive range of parts for Citroën and Peugeot, you will always find the right solution for your specific requirements.