Product Overview

This intake manifold is designed for 1.6 HDi diesel engines used in Citroën and Peugeot vehicles. It is a direct-fit, fully sealing used unit referenced by common part numbers 9653808680, 9684941780 and code 0361N3. The component restores correct air routing to the engine, helps maintain proper boost and idle stability, and is a frequent replacement when soot accumulation or physical damage affects engine performance.

Who Should Buy

Ideal for professional mechanics and DIY enthusiasts performing engine maintenance or repairs on Citroën and Peugeot 1.6 HDi models. The part is often listed and searched by its product codes, so having the reference numbers handy speeds up ordering and fitment checks.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Vehicles Equipped With 1.6 HDi Engine (Examples: Citroën C3, C4, C5, Berlingo; Peugeot 207, 307, 308, Partner)
• Product Codes: 9653808680, 9684941780, 0361N3
• Additional Numbers: 0361N3 | 9653808680 | 9684941780

Installation Recommendations

• Disconnect the battery before starting work.
• Remove airbox and intake ducting to access the manifold. Carefully disconnect electrical connectors and vacuum lines (label hoses if needed).
• Unbolt the intake manifold from the cylinder head. Support wiring looms and sensors to avoid damage.
• Clean mating surfaces thoroughly. Remove soot and carbon deposits around the intake and EGR passages to prevent premature recontamination.
• Replace the intake gasket and any worn vacuum nipples or hoses. Do not reuse damaged seals.
• Refit the manifold and tighten bolts to the manufacturer’s torque specification and sequence.
• Reconnect sensors, vacuum lines and air ducting. Reconnect the battery and run the engine to check for leaks and proper operation.
• Recommended Tools: Socket/Torx set, Torque wrench, Screwdrivers, Cleaning brushes or suitable intake cleaner.

Most Common Cause Of Failure

The primary reason intake manifolds on 1.6 HDi engines fail or require service is soot and carbon buildup from the EGR system, which restricts airflow and can block passages. Other common issues include cracking or deformation of plastic components caused by heat cycling, broken or brittle vacuum nipples, and degraded sealing surfaces or gaskets that lead to air leaks, rough idle, loss of boost and fault codes.

Why Choose This Part

Using a properly sealing intake manifold with correct OEM reference numbers ensures reliable air delivery and helps eliminate vacuum leaks and related drivability problems. The listed part numbers make it easy to match the item with service records or parts catalogs, accelerating repair time in professional workshops and home garages alike.

Order Notes

Search by part number 9653808680, 9684941780 or code 0361N3 to find this unit quickly. Suitable for replacement on many Citroën and Peugeot models equipped with the 1.6 HDi engine—inspect the old part for soot accumulation and cracked outlets when diagnosing intake-related issues.

original air intake for Citroën C1 and Peugeot 107 with a three -cylinder three -cylinder (1KR – FE) gasoline. The 17705-0Q020 and 144091 codes are designed to fit the engine compartment of versions equipped with a robotized transmission or ESP. Proper sealing is essential for stable idle, correct mixture and low consumption – leaks are often manifested by irregular operation, increased consumption and mixture errors (eg P0171).

This part is suitable as a replacement for damaged or rotten plastic intake parts, broken holders or cracked goose necks. These cars with age often suffer from suction with vibrations and heat, leading to hair cracks and fake air suction. Replacement brings an immediate improvement of engine driving culture and eliminates undesirable suction noise.

Installation is usually fast and manageable even in domestic conditions: remove the old part (loosening of the buckle/clips and screws, usually torx), check the seals and bearing surfaces, put on a new piece including all guide pins and fuses and tighten according to the feeling. It is recommended to clean the air filter simultaneously and check the status of adjacent hoses and venting. No calibration of the control unit is required.

Fits the first generation Citroën C1 and Peugeot 107 with 1.0 1 KR engine manufactured in approximately 2005–2014. The version for the robotized gearbox/ESP has a specific shape and attachment due to a different space around the battery and the ABS module – please check the part and equipment code.

Technical information

• Manufacturer: PSA (Citroën/Peugeot)/Toyota OEM
• Model: Citroën C1 I 1.0 1 Kr (1kr -FE); Peugeot 107 I 1.0 1Kr (1kr – FE); cars with a robotized transmission or ESP
• product codes: 17705-0Q020; 144091
• Additional numbers: 177050q020; 1440.91

The advantages of the original part: accurate compatibility without modifications, high -quality material resistant to vibration and heat, correct guidance and damping for quiet operation. Ideal choice for fast and reliable repair without experimenting with universal replacements.

Are you looking for a reliable air intake for your Citroën or Peugeot? This specific component fits models equipped with 1.8 16V and 2.0 16V engines, renowned for their strong performance and durability. The air intake plays a crucial role in the proper functioning of the engine by ensuring the optimal air-fuel mixture, which is essential for engine efficiency and power output.

Installation of this part is typically straightforward and quick, benefiting both experienced mechanics and DIY enthusiasts. Replacing a faulty or worn intake can prevent engine issues such as reduced power, poor fuel economy, or increased emissions.

Technical Information:

• Manufacturer: Citroën Peugeot
• Models: Compatible with Citroën C4, Citroën C4 Picasso, Citroën C5, Citroën C5 X7, Peugeot 307, Peugeot 407
• Product Codes: 9662401480, 0361R0, 0361N8
• Additional Numbers: This component is labeled according to various identification systems for easy reference and interchangeability.

Investing in a high-quality, original part like this air intake helps maintain your vehicle’s optimal condition. Ensuring your engine receives the correct airflow improves its operation and extends its lifespan. Let your car breathe freely again with this dependable air intake component!

Product Overview

This air intake distribution piece is designed for the 1.4 HDi 16V (engine code 8HY) diesel engines used on selected Citroën and Peugeot models. It routes and balances induction air between turbocharger/intercooler plumbing and the intake manifold, contributing to smooth engine response and correct boost behaviour. Replacement part numbers commonly searched for: 9647250480, 0361L4 (also listed as 0361.L4).

Key Benefits

• Direct fit for vehicles equipped with the 1.4 HDi 16V 8HY engine — quick replacement for workshop or DIY repairs.
• Restores proper air routing to eliminate boost leaks, rough idle and loss of power associated with damaged intake distribution components.
• Often sold under original equipment part numbers for straightforward parts lookup.

Technical Information

• Manufacturer: Stellantis
• Model: 1.4 HDi 16V (Engine Code 8HY)
• Product Codes: 9647250480, 0361L4, 0361.L4
• Other Numbers: NFP (where applicable)

Compatibility

Typical applications include Citroën C3 and Peugeot 1007 fitted with the 1.4 HDi 16V 8HY engine. Always match the part numbers listed above with the existing component on the vehicle to confirm fitment.

Installation Recommendations

Recommended for professional fitment or experienced DIY mechanics. Basic replacement steps:

• Disconnect the negative battery terminal before starting work.
• Release intake system pressure and remove any clamps and hoses connected to the distribution piece (turbo/intercooler hoses, PCV lines if present).
• Unbolt the intake distribution from its mounting points, noting bolt locations and any brackets or sensors.
• Replace any sealing gaskets or O-rings with new items to ensure leak-free joints.
• Refit hoses and clamps, then reconnect the battery and verify there are no air leaks or fault codes. Run the engine and check for normal boost response.

Use manufacturer torque settings for fasteners and ensure hose clamps are tightened evenly to avoid deformation. Replace any brittle vacuum hoses or cracked clamps found during the job.

Most Common Failure Causes

Failures are usually caused by age-related degradation of plastic or rubber sections, heat and vibration leading to cracks, or damaged sealing surfaces and O-rings. Build-up of oil vapour and soot from the crankcase ventilation system can accelerate wear. A failing intake distribution commonly produces boost leaks, rough idle, reduced power, and occasional turbo lag.

Service Life And Practical Notes

Life expectancy varies with usage and environment; on high-mileage or older vehicles the part may fail more frequently. Inspect the intake distribution during routine maintenance, especially if the vehicle shows symptoms of air leaks or decreased engine performance. When replacing, always use the correct part numbers for a reliable fit and restore original air routing and sealing.

Description

Direct-fit air intake assembly designed for Citroën C1 and Peugeot 107 equipped with the 1.0 (1KR) engine, manual transmission and no ESP. This intake duct and resonator route fresh air from the filter to the throttle body while reducing intake noise and ensuring steady airflow for reliable combustion. Ideal for professional workshops and experienced DIY mechanics looking for a correct-fit replacement using original product references.

Benefits

• OE-referenced fitment for fast identification and installation (searchable by part numbers).
• Maintains correct air flow characteristics and engine response.
• Helps prevent vacuum leaks and intake noise when installed with proper clamps and gaskets.
• Suitable for routine repairs after damage from heat, impact or age-related degradation.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1, Peugeot 107 – 1.0 (Engine code 1KR)
• Product Codes: 17705-0Q010, 144089
• Additional Numbers: 1KR (Engine Code)

How It Works

The intake assembly channels filtered outside air to the throttle body while smoothing pulsations and reducing intake noise through integrated resonators. A correct, intact intake duct prevents unmetered air from entering the engine, which helps preserve fuel trim accuracy and stable idling.

Common Failure Modes

Failures are typically caused by mechanical damage, age-related material fatigue or heat exposure. Typical issues include cracks in the plastic ducting, torn or hardened connection hoses, broken mounting tabs and degraded seals. Damage allows unmetered air or debris to enter the intake tract, causing rough idle, poor throttle response or check engine codes related to air/fuel mixture.

Replacement and Installation

Basic replacement steps for an experienced mechanic or competent DIYer:

1. Park the vehicle on a level surface, set the handbrake and allow the engine to cool.
2. Remove the engine cover if fitted to access the airbox and intake duct.
3. Loosen clamps and disconnect hoses between the airbox, mass airflow sensor (if applicable) and the throttle body. Note sensor connectors and secure them during work.
4. Unscrew any mounting bolts or clips retaining the intake duct and carefully remove the old part, taking care not to damage attached sensors or hoses.
5. Fit the new intake, ensuring all sealing faces are clean and that hoses and clamps are seated correctly. Replace any worn clamps or gaskets.
6. Reconnect sensors and hoses, tighten clamps to a snug fit (do not overtighten plastic fittings), reinstall engine cover and start the engine to check for leaks and proper idle.

Installation Recommendations

• Use new clamps or original-style clamps when reassembling; old spring clamps often lose tension.
• Inspect related parts (air filter, mass airflow sensor and mounting tabs) and replace if damaged or contaminated.
• Before final assembly, check for vacuum leaks and ensure all electrical connectors are clean and fully seated.
• Follow basic safety procedures: wear gloves and eye protection. Disconnecting the battery is recommended when working near electrical connectors, and always follow vehicle manufacturer guidelines.

Why This Part Is Often Replaced

Air intake ducts are exposed to engine bay heat, vibration and occasional impact. Over time plastic components can become brittle and crack, clamps can corrode or lose tension, and seals can harden. Drivers may notice intake-related faults after collision damage, after prolonged high-mileage use, or when oil contamination and debris degrade flexible hoses.

Fitment Tips

Identify the correct part by matching the product codes 17705-0Q010 and 144089 and the engine code 1KR. The part is intended for vehicles with manual gearbox and without ESP; verify transmission and equipment level before ordering.

Looking for a component to optimize your engine performance? Our air intake for 1.5 HDI engines is the perfect choice for vehicles from Citroën, Peugeot, Fiat, Opel, and Toyota. This part ensures the proper amount and quality of air delivered to the engine, which is crucial for its efficient and smooth operation.

Our air intake is in excellent condition, ensuring that your vehicle will perform like new. Installing this part is quick and easy, which will be appreciated by both professional mechanics and DIY enthusiasts. When replacing, we recommend paying close attention to sealing all connections and checking other intake components to maximize the effectiveness of this replacement.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: 1.5 HDI Engine
• Product Codes: 9827622780
• Other Numbers: CITROEN BERLINGO III, OPEL COMBO E K9, PEUGEOT PARTNER III, PEUGEOT RIFTER, Toyota ProAce City

This part not only increases your engine’s efficiency but also helps maintain lower fuel consumption and reduce emissions, benefiting both you and the environment. Our air intake is designed with an emphasis on durability and longevity, ensuring reliability.

Investing in a high-quality and verified auto part like our air intake protects your engine from potential damage caused by dirt or insufficient air supply. Ensure long-term performance and reliability of your vehicle with this essential piece of technology.

Product Overview

High-quality replacement air intake duct for 1.4 HDi engines used on Citroën and Peugeot models. This part (OEM references 9645371180, 9646698680, 0361N4) restores a sealed airflow path between the air filter housing and the turbocharger/intercooler system, helping to maintain correct boost pressure, throttle response and fuel economy. Designed for professional workshops and experienced DIY mechanics who require a reliable, direct-fit solution.

Fits The Following Models

Compatible With: Citroën C2, Citroën C3, Citroën C3 Pluriel, Peugeot 206, Peugeot 207. Often referenced by product codes 9645371180, 9646698680 and 0361N4.

Installation Recommendations

Replacement Is Straightforward For Experienced Technicians: loosen and remove the clamps securing the original duct to the airbox and turbo inlet, carefully detach any attached sensors or vacuum lines, remove the old duct and fit the new one ensuring all sealing lips sit correctly. Refit clamps and any removed sensors, then perform a visual check for leaks at idle and under boost. Use OEM-style clamps or torque-specified hose clamps to avoid overtightening. Inspect mating surfaces for oil contamination or damage and clean before installation.

Typical Symptoms Of A Faulty Intake Duct

• Loss Of Engine Power And Sluggish Acceleration
• Rough Idle Or Fluctuating RPM
• Increased Fuel Consumption And Reduced Driveability
• Whistling Or Hissing From Engine Bay Under Boost

Why The Part Usually Fails

Air intake ducts are exposed to heat, oil vapour and mechanical stress. Over time the material can harden, crack or split at the bends and connection points. Oil contamination from crankcase ventilation, repeated boost cycles and vibration accelerate degradation. Damage Or Leaks Cause Unmetered Air Ingress Or Loss Of Boost, Which Directly Affects Engine Performance.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: 1.4 HDi Applications – Citroën C2, Citroën C3, Citroën C3 Pluriel, Peugeot 206, Peugeot 207
• Product Codes: 9645371180, 9646698680
• Other Numbers: 0361N4

Tips For A Durable Repair

• Replace Worn Clamps Alongside The Duct To Ensure A Secure Seal.
• Check And Clean The Air Filter Housing And Turbo Inlet For Oil Residue.
• Inspect Associated Vacuum Lines And PCV Hoses; Replace If Brittle Or Cracked.
• After Installation, Verify System Integrity Under Load To Confirm No Leaks.

For Whom This Part Is Intended

Recommended For Professional Auto Technicians And Competent DIY Enthusiasts Working On Citroën And Peugeot 1.4 HDi Engines Who Need A Direct-Fit Replacement Part Referenced By OEM Numbers 9645371180, 9646698680, 0361N4.

Commonly, air intake systems can deteriorate due to heat exposure and contaminants over time, which can lead to decreased engine performance and increased fuel consumption. It’s advisable to inspect your vehicle’s air intake during routine maintenance and replace it if you notice any signs of wear or damage.

Technical Information:

• Manufacturer: PSA
• Model: Citroën C1, Peugeot 107
• Product Codes: 0361Q7, 1606496880
• Additional Numbers: N/A

Usual replacement intervals for the air intake can vary based on driving conditions and maintenance, but it is typically advisable to check this component every 30,000 miles or during regular service intervals. Signs that it may need replacement include reduced engine performance, poor fuel efficiency, or engine stalling.

When replacing the air intake, it is important to ensure that the vehicle is turned off and that the engine has cooled down. The process generally involves disconnecting the intake hose, removing the old unit, and installing the new one followed by reconnecting everything securely.

Technical Information

• Manufacturer: PSA
• Model: Citroën C1, Peugeot 107
• Product Codes: 0361Q8, 1606496980
• Additional Numbers: 0361Q8, 1606496980

Commonly sought by automotive technicians and DIY enthusiasts, this air intake can be replaced relatively easily, making it a great choice for maintenance or upgrades. It’s important to replace this component whenever you notice signs of wear such as irregular engine idling, decreased performance, or unusual sounds from the engine bay.

This air intake serves the critical function of drawing in air to the engine, allowing for the combustion process to occur efficiently. Over time, this part can degrade due to dirt accumulation or exposure to heat, which may lead to reduced engine efficiency and power.

Technical Information

• Manufacturer: PSA
• Model: 1.4 16V
• Product Codes: 9645400680
• Additional Numbers: 0342J2