This left front wiper motor is designed for first‑generation Peugeot 3008 and 5008 models and is commonly referenced by OE numbers 9671062180, 3397021288, 6405PZ and 6405QA. It supplies the drive torque to the wiper linkage on the driver side, restoring reliable wipe function after motor failure or severe wear. Ideal for workshop technicians and competent DIYers who search by part number to find a direct-fit replacement.

How It Works

The wiper motor converts electrical energy from the vehicle into rotational motion, which is transmitted through the wiper linkage to move the wiper arm across the windshield. The unit includes an electric motor and an integrated gearbox to provide the correct torque and intermittent park position. Correct park and intermittent function are essential for safe visibility in adverse weather.

Replacement Procedure

• Disconnect The Battery: Always disconnect the negative terminal before starting to avoid short circuits and to protect onboard electronics.
• Remove Wiper Arms: Mark Wiper Arm Positions Then Remove The Arms From Their Splines.
• Remove Cowl/Trim: Detach The Cowl Panel To Access The Motor And Linkage. Keep Fasteners Organized.
• Disconnect Electrical Connector: Release The Locking Tab And Pull The Connector Free.
• Unbolt Motor And Linkage: Remove Mounting Bolts, Detach The Motor From The Linkage Assembly.
• Transfer Linkage If Required: If The Replacement Does Not Include The Linkage, Transfer The Linkage Or Use The Complete Assembly.
• Fit New Motor: Install The Motor, Tighten Fasteners Securely, Reconnect Electrical Connector.
• Reassemble And Test: Refit The Cowl And Wiper Arms To Marked Positions, Reconnect Battery And Verify Park Position, Intermittent Settings And Full Travel.

Installation Recommendations

• Use Appropriate Tools: Standard hand tools, small socket set and trim tools are sufficient for most replacements.
• Mark Wiper Arm Orientation: Before removal, note or mark the exact parked position to restore correct alignment during reassembly.
• Check Linkage Condition: Inspect Bushings And Joints For Play Or Binding. Replacing A Faulty Linkage Together With The Motor Prevents Premature Failure.
• Protect Electrical Connections: Ensure Connectors Are Clean And Free Of Corrosion. Use Dielectric Grease If Appropriate.
• Follow Safety Practice: Disconnect The Battery Before Work And Avoid Forcing Seized Components To Prevent Damage.

Most Common Failure Reasons

• Water Ingress And Corrosion: Moisture Penetration Causes Electrical Shorting Or Gearbox Corrosion.
• Wear Of Internal Brushes And Commutator: Over Time The Motor Loses Efficiency And Ultimately Fails.
• Mechanical Strain From Stiff Linkage Or Frozen Joints: Excess Load From Corroded Or Seized Linkage Accelerates Motor Wear.
• Electrical Issues: Loose Connectors Or Intermittent Power Supply Can Lead To Erratic Operation.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 3008 I, Peugeot 5008 I
• Product Codes: 9671062180, 3397021288
• Additional Numbers: 6405PZ, 6405QA, 6405.PZ, 6405.QA

Frequently Searched By OE Number: If You Or Your Customers Look Up Parts By Reference, Use 9671062180, 3397021288, 6405PZ Or 6405QA To Find This Item Quickly.

This description Targets Workshop Technicians And Experienced DIYers. Replace The Motor When You Observe Slow Or Intermittent Wiper Movement, Strange Noises From The Cowl Area, Or When Wipers Fail To Park Correctly.

This used right front wiper motor is a direct-fit unit for first-generation Peugeot 3008 and 5008 models, commonly referenced under part numbers 9671062380, 3397021289, 6405PX, 6405PY and 6405PA. It replaces the motor that drives the passenger-side windshield wiper arm and is suitable for mechanics and competent DIYers who need a reliable replacement part to restore correct wiper function.

Key Features And Benefits

• Direct Fit For Original Mounting Points: Designed to match the factory attachment and linkage geometry for straightforward replacement.
• Multiple OEM Cross References: Supplied with commonly used Peugeot/Stellantis part numbers to simplify identification and ordering.
• Practical For Workshop Use: Ideal for professional workshops and experienced home mechanics carrying out scheduled or corrective repairs.
• Cost-Effective Repair Option: Restores wiping performance without the expense of full linkage replacement when motor is the faulty component.

Compatibility

Compatible With: Peugeot 3008 I; Peugeot 5008 I (Passenger/Right Front Wiper). Check listed product codes to confirm fit with your vehicle’s existing motor and linkage arrangement.

Installation Recommendations

• Safety First: Disconnect the vehicle battery before starting work to prevent short circuits and accidental motor activation.
• Tools Required: Torx/Spline Sockets, Ratchet, Screwdrivers, Pliers, Trim Removal Tools, Multimeter for quick electrical checks.
• Basic Replacement Steps: Remove the wiper arm (mark position if necessary), detach cowl or access panel, disconnect electrical connector, unbolt the motor from the linkage/housing, replace with the new unit and refit linkage and seals. Reconnect electrical plug, refit cowl and wiper arm, then test park and sweep positions under power.
• Alignment Tip: Ensure the wiper arm is set to the correct park position before fully tightening. Verify smooth, full-range movement and correct park position during initial test.
• Torque And Fixings: Use correct torque for mounting fasteners per workshop manual where available; avoid over-tightening plastic fasteners.

Reasons Why The Part Commonly Fails

• Water Ingress And Corrosion: Moisture penetrating seals leads to corrosion of gears, motor brushes and electrical contacts.
• Mechanical Wear: Internal gear wear and degraded brushes cause loss of torque or intermittent operation after years of use.
• Linkage Seizure Or Excessive Load: Frozen or misaligned wiper linkage increases motor load and can lead to premature failure.
• Electrical Faults: Connector corrosion, broken wires or poor grounds cause intermittent or no operation.
• Environmental Stress: Salt, road debris and heavy use accelerate wear and reduce service life.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Peugeot 3008 I; Peugeot 5008 I
• Product Codes: 9671062380; 3397021289; 6405PX; 6405PY; 6405PA
• Additional Numbers: 6405PX / 6405PA / 6405PY (Common Cross References)

Practical Notes For Mechanics

Before replacement, verify whether the fault is electrical (check fuse, connector and voltage at the motor) or mechanical (hand-check linkage for free movement). When replacing only the motor, inspect the linkage and pivot bushes for play; worn linkage parts will quickly wear the new motor. After installation, perform several wipe cycles to ensure correct operation and park position.

Product Overview

High-quality Valeo rear wiper motor designed as a direct-fit replacement for a range of Stellantis vehicles. This motor restores reliable rear-wiper operation and is commonly sought under OE and supplier references (e.g. 9680477480, 53031812, 6405JQ). Ideal for professional workshops and experienced DIY mechanics who need a robust, OEM-compatible unit.

Key Benefits

• Direct fit for Citroën C4 II (B7) and multiple Peugeot models, reducing installation time.
• Reliable drive and gearset designed for automotive exterior applications.
• Improves visibility and safety by restoring rear-wiper function.
• Frequently Identified By Part Numbers: 9680477480 / 53031812 / 6405JQ — use these when searching or ordering.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C4 II (B7); Peugeot 308 SW and 308 Hatchback (2010); Peugeot 3008 I; Peugeot 5008 I
• Product Codes: 9680477480, 53031812, 6405JQ
• Additional Numbers: 53031812 | 6405.JQ | 6405JQ | 9680477480

Installation Recommendations

Recommended For Experienced Mechanics And Skilled DIYers. Typical replacement steps:

1. Park vehicle on level ground and switch ignition off.
2. Disconnect the negative battery terminal to prevent short circuits and accidental activation.
3. Remove interior tailgate trim to access the rear wiper motor and linkage—retain clips and screws for reassembly.
4. Disconnect the electrical connector and unbolt the motor from the tailgate.
5. Separate the motor from the wiper linkage; inspect linkage and spindle for wear or corrosion.
6. Fit the replacement motor, reconnect the electrical connector, and loosely mount bolts to check park position and travel before final torquing.
7. Reassemble trim, reconnect battery, and test full wiper function (intermittent, park position, and return to rest).

Always Follow Manufacturer Torque Values And Reassembly Order. Avoid operating the wiper on frozen glass—this can overload the motor and linkage.

Why This Part Fails

• Water Ingress And Corrosion: Rear wiper motors are exposed to moisture; seals can fail allowing water to reach gears and electrical parts.
• Brush And Commutator Wear: Over years of use, brushes wear down and motor performance degrades.
• Mechanical Overload: Attempting to operate the wiper when frozen or jammed can strip gears or overload the motor.
• Linkage Wear Or Seizure: Worn joints or seized linkage increase load on the motor and accelerate failure.

Practical Tips

• Inspect And Lubricate Linkage During Replacement To Extend Service Life.
• Check Tailgate Seals And Drain Channels To Prevent Water Accumulation.
• If The Wiper Stalls Or Moves Erratically, Check Connector Voltage And Ground Before Replacing The Motor.

Compatibility Note

The unit is intended as a replacement for the models listed above. Many customers search using part numbers 9680477480, 53031812 or 6405JQ—use these codes to confirm fitment in catalogs and parts lists.