This is a used wiper mechanism designed for the early generation Citroën C1, Peugeot 107 and Toyota Aygo. Supplied with original product references 85010-0H010 and 6405T0, the unit replaces the complete linkage and motor assembly that drives the front wipers. Ideal for professional workshops and competent DIYers, this part restores reliable wiper movement, correct park position and reduces excessive noise or erratic wiping caused by worn or seized components.

Function And Symptoms

The wiper mechanism converts the electric motor output into the sweeping motion of the wiper arms. Common symptoms of a failing mechanism include intermittent operation, slow or noisy movement, wipers that stop mid-sweep or fail to return to the park position, and visible play or binding in the linkage.

Replacement Procedure

Basic replacement steps (typical labour time 30–60 minutes depending on experience):

• Park vehicle with ignition off, engage parking brake and, as a safety measure, disconnect the negative battery terminal when working on electrical components.
• Remove wiper arms (note their parked position to reinstall correctly) then remove the plastic cowl or trim to access the mechanism.
• Disconnect the electrical connector to the motor and unbolt the mechanism from the body.
• Withdraw the assembly from under the cowl and fit the replacement unit; reconnect the electrical plug and loosely fit bolts.
• Reconnect the battery, briefly energize the motor to confirm movement and correct park position, then tighten mounting bolts to the manufacturer’s torque specification and reassemble trim and wiper arms.
• Check final operation and wipe pattern. If the park position is incorrect, adjust as required following the vehicle service manual.

Installation Recommendations

• Always observe basic electrical safety and, if possible, disconnect the battery before starting work on the wiper motor or wiring.
• Mark the exact position of the wiper arms before removal to avoid alignment issues after installation.
• Inspect link pins, bushes and mounting points for corrosion or excessive wear; replace worn linkage components to avoid premature failure of the new unit.
• Test the mechanism before final reassembly to confirm the park position and smooth operation.
• When uncertain about electrical diagnostics or intermittent faults, check related fuses, relays and wiring for corrosion or poor contacts.

Reasons For Failure

• Water ingress and corrosion of motor brushes, bearings or linkage joints.
• Mechanical wear of gears, bushings or linkage pivots leading to play or binding.
• Overload from frozen or obstructed wipers, which can shear gears or damage the motor.
• Electrical faults such as worn brushes, poor grounding or connector corrosion causing intermittent operation.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1 (First Series), Peugeot 107 (First Series), Toyota Aygo (First Series)
• Product Codes: 85010-0H010, 6405T0
• Other Numbers: 6405T0 | 85010-0H010

Product Overview

This direct-fit wiper mechanism is designed for the first-generation Citroën C1, Peugeot 107 and Toyota Aygo. It replaces the linkage assembly that transfers motor rotation to the wiper arms, restoring smooth, synchronized wiping action. The part is commonly searched and identified by product codes 6405HT and 6405T0.

Function And Benefits

The wiper mechanism converts the electric motor’s rotary motion into the back-and-forth movement of the wiper arms via a linkage and pivot gearbox. A serviceable mechanism ensures clear visibility in rain and snow, quiet operation and proper park position of the wipers. Replacing a worn mechanism removes play, eliminates erratic motion and prevents damage to wiper arms and blades.

Fitment And Application

Fits: Citroën C1 (first series), Peugeot 107 (first series) and Toyota Aygo (first series). Frequently located and ordered by the product codes 6405HT and 6405T0. Suitable as a direct replacement for vehicles with the original wiper linkage arrangement.

Replacement Procedure

Typical replacement steps for a trained mechanic or experienced DIYer:

• Park vehicle with wipers in the parked position and switch off ignition.
• Mark the position of each wiper arm on the glass to ensure correct reinstallation, then remove the wiper arms (remove retaining nuts and pull off covers).
• Remove the cowl/plenum cover to access the mechanism (may require unclipping trim and removing screws).
• Disconnect the electrical connector to the wiper motor and unbolt the mechanism assembly from the body.
• Remove the old mechanism and fit the replacement assembly, securing all mounting points and reconnecting the motor connector.
• Reinstall cowl and wiper arms in their marked positions, tighten nuts and check that wipers park correctly and sweep the full screen without binding.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1 (First Series), Peugeot 107 (First Series), Toyota Aygo (First Series)
• Product Codes: 6405HT, 6405T0
• Other Numbers: Not Specified

Installation Recommendations

Before starting, secure vehicle and follow basic safety rules. It is recommended to disconnect the battery as a precaution against accidental activation of the wiper motor. Mark wiper arm positions on the glass before removal. Inspect wiper motor electrical connector and wiring for corrosion or damage and replace if necessary. Lubricate pivot points lightly with an appropriate automotive grease, and ensure fasteners are correctly seated. After installation, verify full sweep range and park position at low and high speeds. Replace wiper blades if worn to avoid overloading the mechanism.

Why This Part Fails Most Often

Common failure causes include wear of linkage bushings and joints, corrosion from road salt and moisture, ingress of debris or water into the gearbox, and plastic gear wear or breakage. Mechanical overload from frozen or blocked wipers (ice, heavy snow) can accelerate damage. Symptoms of a failing mechanism are unusual noises, loose or jerky motion, incorrect park position or one-sided wiping. Regular inspection and avoiding operating frozen wipers can significantly extend service life.

Overview

This wiper motor and linkage assembly (OEM reference 53565002) is designed for the first-generation Citroën C1, Peugeot 107 and Toyota Aygo. It replaces the complete drive mechanism that moves the wiper arms across the windshield and is suitable for professional workshops and experienced do-it-yourself mechanics looking for a reliable replacement part.

Key Benefits

• Direct fit for first-generation C1 / 107 / Aygo models, reducing installation time.
• Includes motor and linkage for full restoration of wiper function (park position, sweep range).
• Common spare part code 53565002 referenced in many parts catalogs — useful for fast search and ordering.

Function And Symptoms

The wiper mechanism converts the electric motor rotation into the oscillating movement of the wiper arms via a gearbox and linkage. Typical symptoms of a failing mechanism include slow or intermittent wiper movement, grinding or clicking noises, wipers that do not park correctly, or complete loss of movement. Electrical motor failure, seized link joints or worn worm gears are frequent causes.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1 (First Generation), Peugeot 107 (First Generation), Toyota Aygo (First Generation)
• Product Codes: 53565002
• Additional Numbers: N/A

Compatibility

Fits first-generation models produced in the joint venture platform — commonly referred to as the 2005–2014 Citroën C1, Peugeot 107 and Toyota Aygo. Always verify visual match of mounting points and connector type before installation.

Replacement And Installation

Recommended for experienced technicians or skilled DIYers. Typical replacement steps:

• Park wipers in the service position if available, or mark arm positions before removal.
• Disconnect the negative battery terminal to avoid short circuits when handling electrical connectors.
• Remove wiper arms (often secured by nuts hidden under caps), then remove the scuttle/cowl covers to access the motor and linkage.
• Disconnect the electrical connector and unbolt the motor/linkage assembly from the body.
• Install new mechanism, secure mounting bolts to manufacturer torque, reconnect electrical connector and refit covers and wiper arms.
• Set wiper park position and test full sweep and intermittent functions. Adjust arm positions if necessary.

Installation Recommendations

• Always disconnect the battery before working on electrical components to prevent short circuits and unintended activation.
• Inspect wiper arms, blades and linkage bushes during replacement — worn ancillary parts accelerate failure of the new mechanism.
• Use appropriate tools to avoid damaging plastic covers and trim. Apply threadlocker or correct torque where specified by the manufacturer.

Why This Part Fails Most Often

Common failure causes include water ingress and corrosion of the gearbox, wear of the worm gear and bearings, seized linkage joints due to dirt or lack of lubrication, and electrical motor burnout after prolonged heavy use or ice/snow loading. Mechanical shock (e.g., trying to operate wipers while frozen to the glass) significantly shortens lifetime.

Notes For Buyers

This listing refers to the complete wiper motor and linkage assembly suitable for the first-series Citroën C1, Peugeot 107 and Toyota Aygo. The product code 53565002 is provided for quick search and identification. Ideal for garages and experienced DIY mechanics who need a direct-fit replacement to restore reliable wiper operation.

This Wiper Mechanism (motor and linkage assembly) is a direct-fit replacement commonly referenced under part number 85010-0H011. Designed For The First Generation Citroën C1, Peugeot 107 And Toyota Aygo, It Restores Reliable Windshield Wiping Performance For Workshop Technicians And Self-Repair Enthusiasts. The Unit Is Ideal When The Wipers Move Sluggishly, Make Excessive Noise, Fail To Park Correctly Or Stop Working Completely. The Part Number Is Frequently Used In Searches, So Entering 85010-0H011 Will Help You Find The Correct Item Quickly.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1 (First Series), Peugeot 107 (First Series), Toyota Aygo (First Series)
• Product Codes: 85010-0H011
• Other Numbers: Not Specified

Compatibility Notes

Fits First Generation Models Typically Produced Around 2005–2014. Confirm Fitment By Matching The Mounting Pattern And Connector Type On The Vehicle. This Mechanism Replaces Both The Electric Motor And The Linked Gearbox Assembly In Many Applications.

Installation Recommendations

• Disconnect The Battery Before Starting Work To Avoid Short Circuits And Accidental Motor Activation.
• Remove Wiper Arms (Mark Their Park Position), Then Remove The Cowl/Plenum Cover To Access The Motor And Linkage.
• Unplug The Electrical Connector And Unbolt The Motor/Mechanism From The Body. Keep Fasteners And Washers Organized For Reassembly.
• Fit The Replacement Unit, Respect Correct Park Position And Torque Values Where Specified. Reattach The Cowl And Wiper Arms, Then Test Wiper Operation Through Full Sweep And Park Cycles.
• After Installation, Verify That Wipers Park Correctly And Do Not Bind On The Windshield. Adjust Arm Position If Required.

How The Part Is Replaced (Step By Step)

1. Park The Vehicle With The Wipers In The Park Position And Remove The Ignition Key.
2. Disconnect The Negative Battery Terminal.
3. Remove Wiper Arms (Use A Suitable Puller If Necessary) And The Cowl Cover.
4. Disconnect Electrical Connector And Unbolt The Motor/Linkage Assembly.
5. Install The New Mechanism, Secure All Bolts, Plug In The Connector And Refit Cowl And Wiper Arms In Correct Alignment.
6. Reconnect The Battery And Cycle The Wipers To Confirm Proper Operation And Park Position.

Why This Part Fails Most Often

• Water Ingress And Corrosion Of The Motor Or Gearbox, Leading To Seized Gears Or Shorted Windings.
• Wear Of Internal Brushes Or Bearings Causing Reduced Torque And Intermittent Operation.
• Mechanical Wear Or Loosened Linkage Joints Causing Play, Slippage Or Incorrect Park Position.
• Electrical Issues Such As Corroded Connectors, Blown Fuses Or Faulty Relays In The Wiper Circuit.
• Overload From Heavy Loads (Ice/Snow) Leading To Accelerated Wear Or Gear Damage.

Practical Tips For Workshops And DIYers

• Inspect The Wiper Arms And Blades When Replacing The Motor—Worn Blades Increase Load And Reduce Motor Life.
• Check The Fuse And Relay Before Replacing The Motor To Avoid Unnecessary Parts Replacement.
• Lubricate Linkage Pivots With Appropriate Grease During Installation To Extend Service Life.
• Keep The Part Number 85010-0H011 Handy When Searching Or Ordering To Speed Up Identification.

Durability And Expected Service Life

Service Life Depends On Usage And Environmental Conditions. Under Normal Use The Mechanism Commonly Lasts Many Years, But Exposure To Road Salt, Moisture And Mechanical Overloads Can Shorten Lifespan. Typical Failure Window For High-Use Vehicles Is Often Several Years To Over A Decade.

This rear wiper motor by Valeo is a direct replacement part designed for Citroën C1, Peugeot 107, and Toyota Aygo models. As a critical component of the rear windshield wiper system, it ensures effective clearing of the rear glass for improved visibility and safe driving in adverse weather conditions.

The rear wiper motor is responsible for converting electrical energy into mechanical motion, enabling the wiper arm to sweep across the rear window. Over time, wear and tear from constant use and exposure to moisture can cause the motor to malfunction or fail, leading to reduced rear visibility.

Replacing the rear wiper motor typically involves removing the rear wiper arm, detaching the interior rear hatch panel to access the motor, disconnecting the electrical connector, and unbolting the motor before installing the new unit. Regular maintenance and timely replacement can help maintain optimal wiper performance and ensure safety on the road.

Technical Information

• Manufacturer: Valeo
• Model Compatibility: Citroën C1, Peugeot 107, Toyota Aygo
• Product Codes: 85130-0H020, 85130-0H010
• Additional Numbers: OEM numbers often referenced in repair manuals and parts catalogs

Valeo is a recognized French global automotive supplier headquartered in France, listed on the Paris stock exchange (CAC-40 index). It employs over 113,600 people across 33 countries and delivers a wide range of components to OEMs and the aftermarket.

This high-quality rear wiper motor by Valeo is designed for Citroën C1, Peugeot 107, and Toyota Aygo models. It plays a crucial role in maintaining clear visibility by efficiently operating the rear windshield wiper. The motor is engineered to deliver reliable and consistent performance, ensuring safety during poor weather conditions.

Function and Importance: The rear wiper motor powers the wiping mechanism on the back window, removing rain, dirt, and debris to enhance rear visibility. Over time, wiper motors can fail due to wear, electrical issues, or corrosion, leading to a malfunctioning rear wiper. Replacing the motor helps restore proper functionality and contributes to overall driving safety.

Compatibility and Application: This part is suitable for original Citroën C1 and Peugeot 107 models, as well as Toyota Aygo vehicles sharing the same platform and component specifications. It is often referenced by product code 6405T2 or OEM numbers 85130-0H020 and 53025512, making it easier for mechanics and DIY enthusiasts to find the correct replacement part.

Installation Notes: The replacement process typically involves removing the rear wiper arm, detaching the old motor from the vehicle body, disconnecting electrical connectors, and mounting the new motor in place. Care should be taken to align the wiper arm properly to avoid damage or improper wiping angle. Detailed repair manuals or guidance from experienced technicians can assist with a smooth installation.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C1, Peugeot 107, Toyota Aygo
• Product Codes: 6405T2
• OEM Numbers: 85130-0H020, 53025512

Valeo is a leading global supplier in the automotive industry headquartered in France and listed on the Paris Stock Exchange (CAC-40). Its comprehensive product range supports original equipment manufacturers (OEMs) and aftermarket needs worldwide, employing over 113,600 people across 33 countries.