This replacement electric window regulator is designed for professional workshops and competent DIY technicians who service Citroën models. It restores reliable powered raising and lowering of the right rear (passenger side) window and is frequently searched by product codes 9224E4 and 9682632080. The unit is suitable for vehicles from the C4 Picasso/Grand Picasso line and is supplied to fit the original mounting points for a direct and time-saving installation.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 Picasso, Citroën Grand C4 Picasso — Right Rear (Passenger Side)
• Product Codes: 9224E4, 9682632080
• Other Numbers: 92240000

Compatibility & Fitment

Fits right rear door of Citroën C4 Picasso and Grand C4 Picasso models as specified by the manufacturer part references above. Always verify the part number against the one currently fitted on the vehicle — many customers search using the numeric code for quick identification.

Installation Recommendations

• Always disconnect the vehicle battery before beginning work to avoid electrical short circuits and to protect vehicle electronics.
• Remove the inner door trim and water protection foil carefully to access the regulator. Keep fasteners and clips organized for reassembly.
• Support the glass safely (suction cup or tape) before unbolting the regulator to prevent breakage or injury.
• Disconnect the electrical connector and remove mounting bolts. Compare the old unit with the replacement to ensure identical mounting points and connector type.
• Before reassembly, check and lubricate guide rails and contact points with appropriate grease; ensure the window moves freely by hand prior to reconnecting the battery.
• Test full function (up/down, automatic stops if applicable) after reconnection and before final reassembly of trim.

Most Common Failure Causes

• Worn or broken cable/wire mechanism (for cable-driven regulators) leading to loss of movement or jerky operation.
• Motor failure due to wear, overheating or water ingress.
• Corrosion or contamination in guide rails causing increased friction and premature wear of components.
• Broken plastic mounting points or clips that allow misalignment and binding of the glass.
• Electrical issues such as damaged connector pins, wiring harness faults, or switch problems that prevent power delivery to the motor.

Recommended For: Automechanics and experienced DIY enthusiasts who require a reliable replacement part identified by OEM/product codes. Installing a correct-fit regulator restores smooth operation of the rear right window and reduces rework time in the workshop.

Product Overview

This replacement electric window regulator is designed for the left rear door of Citroën C4 Picasso and Grand Picasso models. It includes the mechanical regulator assembly that guides the glass and the cable/slider system driven by the window motor (motor may be integrated or separate depending on version). Ideal for professional workshops and experienced DIYers searching by part number (9682632180 / 9223E0).

Why This Part Fails

• Wear Of Moving Parts: Plastic guides, sliders or cable assemblies wear over time and can break or stretch, causing the window to jam or drop.
• Corrosion And Water Ingress: Moisture inside the door leads to rust on tracks and fasteners or causes electrical connector problems.
• Motor Or Gear Damage: Excessive load from a jammed glass or failed bearings can burn the motor or strip internal gears.
• Fastener And Rivet Failure: Rivets or mounting points can shear, causing misalignment or detachment of the regulator.

Typical Lifetime And Symptoms

Expected service life varies with use and environment; 8–12 years is common under normal conditions. Symptoms of a failing regulator include slow or noisy movement, the window stopping mid-travel, excessive play in the glass, or the glass falling into the door. If you hear grinding, skipping or intermittent motor operation, inspect the regulator and motor assembly.

Replacement Procedure (Overview)

Recommended for trained technicians or experienced DIYers. Typical steps:

• Lower the window (if possible) to access mounting points, then remove interior door trim and moisture barrier carefully.
• Disconnect the electrical connector to the window motor. Before working, disconnect the battery to avoid short circuits and accidental window movement.
• Support the glass in position (suction cups or tape) and remove bolts/rivets securing the regulator to the door and glass.
• Remove the old regulator assembly and compare mounting points and connectors with the new unit.
• Install the new regulator, attach the glass, reconnect the motor connector and check operation before reassembling the door trim.
• Adjust window alignment if needed and verify smooth operation through full travel. Refit all trim and ensure door seal integrity.

Installation Recommendations

• Always Disconnect Battery Before Work: Reduce risk of electric short or accidental motor activation.
• Inspect Door Drainage And Seals: Clear drainage holes and verify moisture barrier condition to prevent future corrosion.
• Use Correct Fasteners: Replace rivets or bolts with OEM-equivalent hardware and torque to manufacturer values.
• Test Before Final Assembly: Verify correct motor direction, full travel and absence of binding before refitting the trim.
• Lubrication: Apply appropriate lubricant to guide rails and sliders (use non-greasy products recommended for window mechanisms) to prolong life.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C4 Picasso, Citroën Grand Picasso
• Product Codes: 9682632180, 9223E0
• Other Numbers: 30S3700025488

Compatibility And Notes

This regulator is specified for the left rear door (rear left, passenger/driver side depending on market). Confirm the part numbers printed on the old regulator match the numbers above when possible. The unit’s connector shape and mounting points should match the original; visual comparison is recommended during replacement.

Who Should Install

Recommended for professional technicians and skilled DIYers comfortable with door trim removal and electrical connectors. If uncertain about procedure or alignment, seek assistance from a workshop to avoid damage to the glass or door interior.

High-quality power window regulator assembly designed for the left rear (driver’s side rear) of Citroën C4 Picasso models. This complete unit includes the electric motor and mounting points for direct replacement of a worn or failed regulator. Ideal for professional workshops and competent DIY mechanics who service Stellantis group vehicles. Commonly searched under product code 9223C1, the part restores smooth, quiet window travel and reliable operation of the rear door glass.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C4 Picasso, Citroën C4 Picasso Grand
• Product Codes: 9223C1
• Additional Numbers: Not Available

Compatibility And Application

Fits Left Rear Door (Driver’s Side Rear) on Citroën C4 Picasso and C4 Picasso Grand models. Suited for vehicles equipped with electric window operation. Always confirm part code against the vehicle’s existing component when possible.

Function And Common Failure Causes

The window regulator controls vertical movement of the door glass by converting motor rotation into linear motion via cables, guides or a scissor mechanism. Typical symptoms of regulator failure include slow or jerky movement, glass misalignment, grinding or clicking noises, or a window that will not move at all.

Common reasons For Failure:

• Worn Electric Motor Brushes Or Bearings Causing Loss Of Torque.
• Frayed Or Broken Cables And Plastic Guides Becoming Brittle Over Time.
• Corrosion Or Water Ingress Leading To Seizure Of Mechanical Parts.
• Impact Damage From Door Collisions Or Slamming.
• Accumulated Dirt And Lack Of Lubrication Causing Increased Wear.

Replacement Guide And Recommendations

Basic Replacement Steps (Summary):

• Disconnect The Battery Before Starting Work To Prevent Short Circuits And Accidental Motor Activation.
• Remove Interior Door Trim And Vapor Barrier Carefully To Access The Regulator Assembly.
• Support The Glass Securely (Suction Cups Or Tape) And Unbolt The Regulator From The Glass And Door Shell.
• Disconnect The Electrical Connector And Remove The Old Regulator And Motor Assembly.
• Install The New Regulator In Reverse Order, Check Cable Routing And Fastener Tightness, And Reconnect The Motor.
• Manually Position The Glass And Perform An Operational Test Before Reassembling The Door Trim; Adjust Regulator Mounting If Necessary To Ensure Smooth, Even Movement.

Recommended Tools: Torx/Phillips Sockets, Panel Removal Tools, Torque Wrench For Door Fasteners, Insulating Tape Or Suction Cups For Glass Support.

Tips For A Reliable Repair

• Always Test Window Travel Several Times After Installation To Confirm Smooth Operation And Correct Alignment.
• Lubricate Moving Tracks Lightly With A Suitable Dry Or Silicone-Based Lubricant To Reduce Wear.
• Inspect Door Seals And Drainage Paths For Blockages To Prevent Future Water Damage.
• Replace Both Sides Or Complementary Components If Wear Is Evident To Avoid Repeat Repairs.

Why Choose This Part

This complete regulator with motor offers a direct-fit solution to restore the original function of the left rear window on C4 Picasso models. The part is frequently referenced by code 9223C1, making it easy to find for swift procurement and workshop scheduling. Suitable for automotive technicians and experienced DIYers seeking a dependable replacement that addresses common wear points in older regulators.

Product Overview

This electric window regulator mechanism is designed for the right front (passenger-side) window of Citroën C4 Picasso and Grand C4 Picasso models. It restores smooth and reliable up/down movement of the door glass and is a common direct-replacement part for workshops and DIY enthusiasts. The part is frequently searched by reference numbers 9222CT and 1675404080, so including these codes in your lookup will speed up finding the correct unit.

Key Features

• Electric Window Regulator Mechanism — Complete assembly for window movement.
• Right Front (Passenger Side) Fitment — Intended specifically for the front right door.
• Direct Replacement — Fits Citroën C4 Picasso and Grand C4 Picasso applications identified by the listed codes.
• Commonly Referenced By Part Numbers — 9222CT, 1675404080 for faster identification.
• Suitable For Professionals And DIYers — Straightforward replacement with standard tools.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 Picasso, Grand C4 Picasso
• Product Codes: 9222CT, 1675404080
• Additional Numbers: 1675404080 | 9222CT

Installation Recommendations

• Disconnect The Battery Before Starting Work To Prevent Short Circuits And Protect The Vehicle Electronics.
• Remove Door Trim Carefully And Store Fasteners In Order. Protect Door Panel Clips During Disassembly.
• Peel Back The Water Shield Gently To Access The Regulator And Motor Assembly; Avoid Damaging The Vapor Barrier.
• Support The Window Glass Securely Before Removing The Regulator To Prevent Glass From Dropping Or Breaking.
• Disconnect Electrical Connector(s) And Unbolt The Regulator/Motor Assembly. Transfer Any Required Clips Or Brackets From The Old Unit If Necessary.
• Install The New Unit, Reconnect The Motor, Temporarily Reconnect The Battery And Test Full Travel Before Final Reassembly.
• Lubricate Guide Rails Lightly With Suitable Grease And Check For Smooth Operation And Proper Alignment.
• Reassemble Door Panel And Recheck Window Operation And Switch Functionality.

Why This Part Most Commonly Fails

• Wear Of Cable Or Plastic Sliders Causing Slippage Or Jamming.
• Motor Burnout Due To Age, Overload, Or Repeated Stall Conditions.
• Water Ingress And Corrosion That Affect Electrical Connections Or Mechanical Components.
• Broken Or Fatigued Mounting Points And Guide Rail Wear From Long-Term Use.
• Impact Damage From Door Or Window Misuse That Deforms Tracks Or Breaks Components.

Notes For Mechanics And DIY Enthusiasts

This part is commonly sought by its reference numbers (9222CT, 1675404080) — include these when searching to improve match accuracy. Ensure you are replacing the right-side front (passenger-side) regulator. After installation, verify smooth travel across the full window stroke and confirm that the switch, glass alignment, and door seals operate correctly to avoid premature wear. Regular maintenance, keeping drain channels clear and light lubrication of guide rails, helps extend the life of the regulator.

High-quality replacement electric window regulator mechanism designed for the left front (driver’s side) of Citroën C4 Picasso and C4 Grand Picasso. This unit restores smooth and reliable operation of the front window, eliminating common issues such as slow movement, noisy operation, or a window that won’t stay in position. Commonly searched under OEM codes 9221CV and 1675403980, this part is suitable for both professional workshops and experienced DIY enthusiasts who perform door repairs and window system maintenance.

Technical Information

• Manufacturer: Stellantis (Citroën)
• Model: Citroën C4 Picasso, Citroën C4 Grand Picasso — Left Front (Driver’s Side)
• Product Codes: 9221CV, 1675403980
• Other Numbers: Commonly referenced by the above OEM codes in parts catalogs and service manuals

Function

The window regulator converts electric motor torque into linear motion to raise and lower the door glass. The mechanism typically consists of a scissor or cable-driven regulator, guide rails, sliders, and an electric motor (depending on version). Proper function ensures the glass moves smoothly, seals correctly, and remains stable at any selected position.

Fitment And Application

Direct fit for left front (driver) door of Citroën C4 Picasso and C4 Grand Picasso models. Check the OEM product codes (9221CV / 1675403980) against vehicle parts lists when matching to specific model years and trim levels to ensure correct fitment.

Replacement Procedure (Overview)

1. Remove the interior door trim and any vapor barriers to access the regulator assembly.
2. Disconnect the electrical connector to the window motor.
3. Support the glass (tape or suction support) and unbolt the regulator from the glass and door frame.
4. Remove the old regulator and motor assembly, install the replacement unit, and reattach the glass and fasteners.
5. Reconnect the electrical connector and test window operation before reassembling door trim.

Installation Recommendations

• Disconnect the vehicle battery before starting work to prevent short circuits and accidental motor activation.
• Use proper trim tools to avoid damaging door panels and clips. Replace any broken clips or fasteners.
• Inspect and lubricate guide rails and contact points with an appropriate grease to ensure smooth operation.
• After installation, cycle the window several times to verify smooth travel, correct alignment, and absence of binding or unusual noise.
• Torque fasteners to manufacturer specifications and ensure the glass is properly seated in its channels.

Why The Part Most Often Fails

Window regulator mechanisms typically fail due to wear of moving parts (cables, sliders, plastic guides), corrosion from moisture ingress, broken plastic components, or motor burnout after many cycles. Dirt and lack of lubrication increase friction and accelerate wear. Heavy use, frequent stop/start of the window, and water leaks into the door cavity are common contributing factors.

Notes For Buyers

When ordering, reference OEM codes 9221CV and 1675403980 to improve the chance of a correct match. Suitable for professional fitters and competent DIY mechanics comfortable with door disassembly and electrical connections. Proper installation restores factory-like window function and reduces future failure risk when combined with correct lubrication and sealing of door cavities.

High-quality replacement electric window regulator designed for the right rear (passenger side) of Citroën C4 Picasso and Grand models. Supplied with electric motor and intended for professional fitment by mechanics or experienced DIYers. The unit restores smooth and reliable window travel, eliminates rattles and slow or stuck windows, and is commonly searched by its product code 9224C5. Ideal when the original mechanism shows signs of wear, broken sliders, frayed cables, or motor failure.

Key Features

• Complete regulator mechanism including electric motor for direct replacement.
• Designed for right rear (passenger side) installation in Citroën C4 Picasso and Grand vehicles.
• OE-Referenced Part Number: 9224C5 — commonly used keyword for fast search and fitment checks.
• Restores factory functionality: smooth up/down travel, reliable switch response and reduced noise.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 Picasso, Citroën C4 Grand Picasso
• Product Codes: 9224C5
• Additional Numbers: Not Available

Compatibility And Fitment

Intended for the right rear (passenger side) window of Citroën C4 Picasso and C4 Grand Picasso. Often searched and identified using the product code 9224C5. Suitable for vehicles using an electric regulator with motor mounted as a single assembly. Verify physical match with the removed unit before installation.

Installation Recommendations

• Always disconnect the battery before starting work on electrical components to avoid short circuits and accidental operation.
• Remove the door trim carefully, taking care with plastic clips and wiring harnesses. Keep fasteners and clips organized for reassembly.
• Support the glass in the closed position (use tape or a support tool) before unbolting the regulator from the window glass.
• Disconnect the motor electrical connector, unbolt the regulator and motor assembly, and remove the old unit from the door cavity.
• Fit the new regulator and motor, secure mounting points, reconnect the motor connector and temporarily reconnect the battery to test operation and glass alignment.
• Adjust window alignment so that it seals correctly in the frame and moves freely through the full travel without binding. Test several up/down cycles before final reassembly.
• Replace worn plastic clips, guide channels or drainage seals as necessary. Apply light lubrication to rails if specified by manufacturer.
• Reinstall door trim only after confirming correct operation and that no abnormal noise or binding occurs.

Why This Part Fails

• Motor Wear: Repeated use, heat and age can cause motor brushes or gear wear, resulting in slow or non-functioning movement.
• Cable Or Slider Failure: Frayed cables or broken plastic sliders are common causes of jammed or uneven window travel.
• Corrosion And Water Ingress: Moisture entering the door can corrode metal components and seize moving parts.
• Mechanical Damage: Impact, forced manual operation or misalignment of the glass can overload and break internal parts.
• Lack Of Maintenance: Dirt in guide channels and dried lubrication increase friction and accelerate wear.

Tip For Mechanics And DIYers

Inspect guide channels, seals and door drainage while the door trim is removed. Replace brittle clips and lubricate sliders with suitable grease. Test the full travel of the window before final reassembly. Keep the original part number 9224C5 handy when ordering or cross-referencing replacements for faster identification.

This power window motor is suitable for the front right (passenger side) window of Citroën C4 Grand/Grand Picasso models produced until 2013. Frequently searched by part numbers 9674032480, 9222CX and 9222GZ, this component replaces the electric drive that raises and lowers the door glass. Designed for mechanics and experienced DIYers, the description below explains fitment, function, common failure causes and practical installation tips to help you get the job done quickly and reliably.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C4 Grand Picasso / C4 Picasso (up to 2013)
• Product Codes: 9674032480, 9222CX, 9222GZ
• Additional Numbers: Commonly referenced under OEM references 9674032480 / 9222.CX / 9222.GZ

Function

The unit is an electric window regulator motor that drives the mechanism to raise and lower the front right door glass. It converts electrical input from the window switch into rotational motion that, via a gearbox or cable/regulator assembly, moves the window. Proper operation ensures smooth, quiet movement and correct positioning of the glass.

Common Reasons For Failure

• Wear Of Brushes Or Commutator: Over time the motor brushes and commutator wear, reducing torque and causing intermittent operation or complete failure.
• Water Ingress And Corrosion: Door sealing or blocked drainage allows moisture to reach the motor and electrical connector, causing corrosion and short circuits.
• Gear Or Cable Damage: Plastic gears or cables inside the regulator can strip or fray, preventing the motor from moving the glass under load.
• Overload And Thermal Stress: Repeated heavy use or a seized regulator increases load and overheats the motor.
• Connector Or Wiring Faults: Corroded pins or damaged wiring can interrupt power supply to the motor.

Replacement Procedure (Overview)

1. Disconnect Battery: Before starting any work on door electrics, disconnect the negative battery terminal to avoid shorts and protect vehicle electronics.
2. Remove Door Trim: Carefully detach the door trim panel and any clips, then remove the water barrier to access the regulator area.
3. Support Glass: Lower the window to a position where you can access mounting bolts, then support the glass or secure it in place to prevent dropping.
4. Disconnect Motor Connector: Unplug the electrical connector to the motor and remove any retaining clips.
5. Unbolt Motor/Regulator Assembly: Remove the bolts that secure the motor to the regulator or door shell. If replacing only the motor, detach it from the regulator gearbox.
6. Install New Unit: Fit the replacement motor, reconnect electrical connector and ensure correct engagement with regulator gears or cables.
7. Test Operation: Reconnect battery temporarily and test window movement through full travel to verify smooth operation before final reassembly.
8. Reassemble Door: Refit water barrier, trim panel and all fittings. Confirm drainage holes are clear and seals are intact.

Installation Recommendations

• Always Disconnect The Battery Prior To Work To Protect Electronics And Avoid Short Circuits.
• Check Drainage And Seals In The Door; Clear Blocked Drain Holes To Prevent Future Water Damage.
• Inspect Regulator For Wear: If the regulator shows damaged gears or frayed cables, replace the entire regulator assembly together with the motor.
• Lubricate Moving Points Lightly With Appropriate Grease To Reduce Friction And Noise.
• Test Full Travel And Auto-Functions After Installation; Adjust Glass Position If Necessary To Avoid Pinch Or Binding.
• If In Doubt, Use Professional Tools Or Seek Experienced Assistance—Correct Alignment And Secure Fastening Are Critical For Reliable Operation.

Frequently Searched Part Numbers: 9674032480, 9222CX, 9222GZ — ideal when searching catalogs or replacement listings. Suitable for Citroën C4 Grand Picasso and C4 Picasso models produced up to 2013. Order this front right (passenger side) window motor to restore smooth, reliable window operation.

This genuine-fit replacement motor restores reliable power operation to the left front (driver side) window of Citroën C4 Picasso / C4 Grand Picasso models produced up to 2013. Often searched by part numbers 9674032580, 9221CY or 9221HH, this unit is suitable for workshops and experienced DIY mechanics who need a direct, durable repair for a sticking or non-moving window.

Key Benefits

Fast Fit: Direct replacement for original equipment motor mounting and electrical connector. Improved Comfort: Restores smooth, quiet window travel and precise stopping positions. Workshop Friendly: Ideal for professional fitting with standard door disassembly tools. SEO Keywords: Window Regulator Motor, Citroën C4 Grand Picasso Motor, Left Front Window Motor, 9674032580, 9221CY, 9221HH.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 Picasso / C4 Grand Picasso (up to 2013) – Driver Side, Left Front
• Product Codes: 9674032580, 9221CY, 9221HH
• Additional Numbers: 9221HH (cross reference listed by some suppliers)

Installation Recommendations

• Safety First: Disconnect the negative battery terminal before starting work to avoid short circuits and accidental window movement.
• Door Disassembly: Remove door trim panel and protective water shield carefully to access the regulator assembly. Keep fasteners and clips organized for reassembly.
• Motor Removal: Disconnect the electrical connector, unbolt the motor from the regulator plate and free the regulator cable or gear from the motor spline. Note the position of the glass and regulator before removal.
• Lubrication And Check: Inspect regulator tracks and cables for wear. Lightly lubricate sliding points and clean out debris before installing the new motor.
• Functional Test: Reconnect the battery and test full window travel before refitting the door card. Verify correct up/down travel and auto-stop positions if equipped.
• Final Steps: Refit the water shield and door trim, ensuring all clips and screws are secured. Adjust window alignment if necessary.
• Recommendation: Use basic hand tools and, if available, a trim removal set. For complex regulator types, assistance from a trained technician can reduce risk of damage to the glass or clips.

Why This Part Fails

Power window motors commonly fail due to wear of internal brushes and commutator, gear or plastic spline wear, water ingress through damaged door seals, seized regulator bearings, or cable fraying. Frequent use, dirt accumulation and corrosion accelerate wear. Symptoms include slow or intermittent movement, grinding noises, complete loss of movement, or the window stopping mid-travel.

Practical Notes For Mechanics And DIYers

Search By Part Number: Customers and workshops frequently locate this motor by the OEM numbers (9674032580, 9221CY, 9221HH) — include these in your search to find the correct replacement. If the regulator assembly shows heavy wear or bent arms, replacing the motor alone may not solve alignment or noise issues; inspect the whole regulator.

Compatibility And Fitment

Designed For Citroën C4 Picasso And C4 Grand Picasso Models Produced Up To 2013, Left Front (Driver Side). Verify physical match of mounting points and connector against the removed unit before final installation.

Warranty And Quality

Supplied As A Direct-Fit Replacement Unit Intended To Meet The Original Specification For Fit And Function. For long-term reliability, ensure door seals and drainage are intact to reduce moisture exposure to the motor.

This used left front power window motor is a direct-fit replacement for Citroën C4 Grand Picasso models manufactured up to 2013. Supplied with OEM cross-reference numbers to help you find the correct part quickly (common search terms: window motor, power window motor, left front, driver side, Citroën C4 Grand Picasso, 9682495680). Designed for mechanics and DIY enthusiasts who need a reliable unit to restore smooth window operation and eliminate grinding or non-responsive switches.

Function And Benefits

The motor drives the window regulator mechanism to raise and lower the left front (driver side) window. It converts electrical input from the window switch into rotational torque, which the regulator translates into linear movement of the glass. Replacing a worn or failed motor restores quiet, consistent operation and prevents further damage to the regulator and door trim.

Typical Failure Modes And Lifespan

Common causes of failure include worn motor brushes, gear wear or broken plastic gears, water ingress and corrosion, seized regulator bearings or worn window guides that overload the motor. Lifespan depends on usage and environment; units commonly fail after several years or after prolonged use in harsh conditions (moisture, dirt, frequent operation). Symptoms of a failing motor are slow movement, intermittent operation, grinding noises, or complete lack of movement from the affected door.

How To Replace

• Prepare Tools: Screwdrivers, trim tools, socket set, possibly Torx bits and a support for the glass.
• Safety First: Disconnect the vehicle battery before starting work to prevent short circuits or accidental motor operation.
• Remove Door Trim: Carefully detach the interior door panel and any vapor barrier to access the regulator and motor.
• Support The Glass: Secure the window in position (tape or support) before loosening regulator fasteners.
• Disconnect Electrical Connector: Unplug the motor wiring harness, then remove the mounting bolts holding the motor to the regulator/door.
• Install Replacement: Fit the replacement motor, tighten fasteners to a secure fit, reconnect the electrical connector and test window operation before reassembling the door.
• Reassemble: Reinstall vapor barrier and door trim, reconnect the battery, and perform a final test of the window function.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4 Grand Picasso (Up To 2013) — Left Front / Driver Side
• Product Codes: 9682495680
• Other Numbers: 9221CY, 9221HH

Installation Recommendations

• Follow standard safety procedures and remove battery negative terminal before disassembly to avoid electrical shorts.
• Test the motor function before final reassembly to ensure correct operation and to avoid repeated removal of the door trim.
• Inspect window tracks and regulator mechanism for wear or damage; lubricate moving parts with suitable grease to reduce friction and extend service life.
• If the regulator shows excessive play or damaged components, replace the regulator assembly together with the motor to prevent premature motor failure.

Why This Part Often Fails

Window motors are exposed to frequent mechanical and environmental stresses. Repeated cycles combined with contaminated or dry guide rails increase motor load and accelerate wear. Moisture or door seal failures can lead to corrosion or electrical faults. Plastic gear sets inside the regulator or motor can crack under stress, causing grinding and loss of movement. Addressing worn guides and sealing issues when replacing the motor will improve longevity.

Notes For Purchase

Search by OE numbers (9682495680, 9221CY, 9221HH) to ensure fast compatibility results. This listing targets professional mechanics and experienced DIYers who want a cost-effective replacement to restore left front window operation on Citroën C4 Grand Picasso vehicles up to 2013.

This Electric Window Motor Is A Direct Replacement For The Right Front (Passenger Side) Window Regulator On Citroën C4 Picasso / Grand Picasso Models Up To 2013. Designed For Workshop Use And DIY Repairs, The Unit Replaces Failed Or Sluggish Window Motors And Restores Smooth, Reliable Window Operation. Ideal For Mechanics And Enthusiasts Searching By Part Number (9682495580, 9222CX, 9222GZ), This Motor Offers A Cost-Effective Way To Eliminate Common Window Faults Such As No Movement, Intermittent Operation Or Grinding Noises.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot Fitment)
• Model: Citroën C4 Picasso / C4 Grand Picasso (Up To 2013)
• Product Codes: 9682495580
• Other Numbers: 9222CX, 9222GZ
• Position: Right Front / Passenger Side
• Voltage: 12V (Standard Automotive)

Application

Fits Right Front Door Window Regulator On Citroën C4 Picasso And C4 Grand Picasso Models Produced Up To 2013. Compatible Where Original Equipment Uses Part Numbers 9682495580, 9222CX Or 9222GZ.

Installation Recommendations

• Disconnect The Battery Before Starting Work To Prevent Short Circuits And Protect Vehicle Electronics.
• Remove Inner Door Trim Carefully To Access The Regulator And Motor; Preserve Clips And Fasteners For Reuse.
• Support The Window Glass While Detaching The Motor/Regulator To Avoid Glass Drop Or Damage.
• Disconnect Electrical Connector And Unbolt The Motor From The Regulator Assembly. In Some Cases It Is Easier To Remove The Entire Regulator With Motor As One Unit.
• Before Final Reassembly, Reconnect The Motor And Test Window Function Several Times To Ensure Smooth Travel And Correct Alignment.
• Observe Manufacturer Torque Values For Fasteners And Reinstall Door Trim Securely.

How To Replace (Summary)

• Lower Or Support Window Glass; Remove Door Trim Panel.
• Peel Back Moisture Barrier Carefully To Access Components.
• Unplug Motor Electrical Connector And Remove Mounting Bolts.
• Transfer Any Required Parts From Old Motor To New Unit Or Replace Entire Regulator If Needed.
• Reconnect Connector, Reconnect Battery, And Test Operation Before Reinstalling Trim.

Why The Part Most Frequently Fails

Window Motors Fail Most Often Due To Mechanical Wear And Environmental Factors: Internal Brush Wear, Worn Gear Teeth, Or Plastic Gear Degradation Lead To Loss Of Drive Or Grinding Noises. Water Ingress And Corrosion From Door Seals Or Damaged Moisture Barriers Accelerate Failure. Overloaded Regulators (Sticking Glass Or Misaligned Tracks) Cause Excessive Motor Load And Premature Burnout. Electrical Issues Such As Faulty Connectors Or Intermittent Wiring Can Produce Sporadic Operation.

Practical Tips

• Always Check Regulator Condition When Replacing The Motor; Bent Tracks Or Frayed Cables Commonly Cause Repeat Failures.
• Lubricate Window Tracks And Guide Points During Installation To Reduce Load And Extend Service Life.
• Test Full Travel And Anti-Pinch Function (If Applicable) After Installation To Ensure Safe Operation.

Keywords: Right Front Window Motor, Window Regulator Motor, Citroën C4 Picasso Window Motor, 9682495580, 9222CX, 9222GZ, Passenger Side Window Motor.