Overview

This replacement window and mirror switch is intended for Peugeot 3008 I and Peugeot 5008 I (T84) models. Designed for workshop use and DIY mechanics, the unit restores control of power windows and electric mirror adjustment/folding functions. Commonly searched by part numbers 96650620ZD and 6490X5, this switch is a practical spare when the original driver door control module becomes intermittent or non-functional.

Key Benefits

• Direct Fit For Driver Door Switch Panel — Simple Swap Without Modifications
• Restores Window Operation, Mirror Adjustment And Folding Where Equipped
• Suitable For Professional Garages And Experienced DIY Repairers
• Identifiable By Manufacturer Numbers 96650620ZD And 6490X5 For Faster Search

Application

Primary Fitment: Peugeot 3008 I (First Generation, T84) and Peugeot 5008 I (First Generation, T84). Ideal for vehicles where the master switch fails to operate one or more windows, or where mirror adjustment/folding is unreliable.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 3008 I (T84), Peugeot 5008 I (T84)
• Product Codes: 96650620ZD, 6490X5
• Additional Numbers: 6490X5, 96650620ZD

Installation Recommendations

Recommended For: Auto Technicians And Competent DIYers Familiar With Door Trim Removal.

• Prepare The Vehicle: Park On A Level Surface And Isolate The Ignition.
• Safety First: Disconnect The Negative Battery Terminal Before Working On Door Electronics To Avoid Short Circuits And Unintended Operation.
• Remove Door Trim Panel Using Plastic Trim Tools To Prevent Damage To Clips And Upholstery.
• Unplug The Wiring Harness From The Existing Switch, Release Any Retaining Clips And Extract The Old Unit.
• Install The Replacement Switch By Reversing The Procedure: Connect The Harness, Snap The Switch Into The Door Trim, And Refit The Door Panel.
• Test All Functions Before Final Assembly: Operate All Windows, Mirror Adjustment, Mirror Folding (If Equipped) And Any Integrated Heating/Motion Functions.

Why This Part Fails

Master window and mirror switches commonly fail due To Mechanical Wear And Electrical Contact Degradation. Frequent Use, Dirt, Moisture Ingress From Window Seals, And Corrosion Of Internal Contacts Lead To Intermittent Operation Or Complete Loss Of Function. Impact Damage From Door Closing Or Rough Handling During Previous Repairs Can Also Cause Failures.

Practical Tips

• If A Single Window Operates Erratically While Others Are Fine, Test The Individual Motor And Wiring Before Replacing The Master Switch.
• When Replacing The Switch, Inspect Wiring Connectors For Corrosion And Ensure Secure Grounds To Avoid Recurring Faults.
• Keep Part Numbers 96650620ZD And 6490X5 Handy When Searching Stock Or Cross-Referencing To Ensure Fast Identification.

Final Notes

This switch is a straightforward repair to restore essential comfort and safety functions in the cabin. For technicians, the part numbers included will speed up parts lookup and inventory management. For DIYers, follow the installation recommendations and test all functions thoroughly after installation.

Description

Direct-fit replacement passenger window switch designed for Citroën C3 II (2009–2016). This OE-compatible switch restores reliable control of the front passenger window with the original look and tactile feedback. Finished in Cornelie Black (FXT), it is intended for the front passenger side control panel and is suitable for both professional workshops and competent DIYers who perform interior trim work.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 II (A51) 2009–2016
• Product Codes: 96637533XT, 98012512XT
• Additional Numbers: 6490CG, A51

Compatibility And Fitment

Compatible with Citroën C3 II models produced between 2009 and 2016. Matches original mounting points and electrical connector pinout used in standard C3 II passenger door switch assemblies. Always verify part numbers against vehicle paperwork or door switch stamping where available.

How The Part Is Replaced

Replacement is straightforward for a trained technician or experienced DIYer. Typical procedure:

• Remove the interior door handle trim and door card using suitable trim tools to avoid damaging clips.
• Carefully pry out the old switch module from the door armrest bezel.
• Disconnect the electrical connector(s) from the old switch and inspect for corrosion or damaged pins.
• Fit the new switch, connect the wiring harness, and test window operation before reassembling the door card.
• Reinstall trim pieces and ensure all clips are properly seated.

Installation Recommendations

• Disconnect The Vehicle Negative Battery Terminal Before Working On Electrical Components.
• Use Proper Trim Tools To Avoid Breaking Door Panel Clips And Plastic Retainers.
• Inspect Connector Pins And Wiring For Corrosion Or Damage; Clean Contacts If Necessary.
• Test The Switch Operation And Window Function Before Fully Reassembling The Door Panel.
• If Window Still Does Not Operate Smoothly, Check The Window Regulator And Motor To Avoid Replacing The Switch Unnecessarily.

Why The Part Fails Most Often

Window switches typically fail due to wear of internal electrical contacts from frequent use, ingress of moisture or dirt, and liquid spills that corrode contacts. Mechanical wear or physical impact to the switch bezel and buttons can also cause malfunction. In some cases, repeated attempts to operate a jammed window place extra load on the switch and lead to premature failure.

Notes For Mechanics And DIY Enthusiasts

Designed To Meet The Expectations Of Professional Workshops While Remaining Accessible For Competent Home Mechanics. The switch offers a cost-effective fix for intermittent or non-functioning passenger window controls and is a common service item during door trim or electrical repairs. Keep the connector clean and secure during installation to ensure long-term reliability.

Order this Citroën C3 II front passenger window switch by referencing product codes 96637533XT / 98012512XT / 6490CG for fast identification and correct fitment.

Product Overview

High-quality replacement power window switch designed for Citroën C3 II (A51) produced between 2009 and 2016. This unit is suitable for use in both the driver and front passenger doors and carries OEM cross-references used by Stellantis for Citroën and Peugeot vehicles. The control offers reliable actuation of the window regulator and fits original mounting points for straightforward installation.

Why Choose This Window Switch

• Direct fit for Citroën C3 II models 2009–2016, minimizing adaptation time.
• OEM cross-reference numbers included to simplify part identification.
• Designed for professional garages and DIY mechanics who need a robust, serviceable switch.
• Black Cornelie finish (FXT) matches original interior trim styling.

Installation

Replacing the window switch is a routine repair for garages and experienced DIYers. Typical procedure:

• Disconnect the vehicle battery before starting to prevent short circuits and inadvertent operation.
• Carefully remove the door trim panel or the switch trim bezel (depending on trim level) using appropriate trim tools to avoid damaging clips and door card finish.
• Unplug the electrical connector from the old switch and release any retaining clips.
• Remove the old switch and install the new unit, ensuring correct orientation and secure locking of retaining clips.
• Reconnect the connector and briefly reconnect the battery to test switch function (up/down, auto functions if present) before refitting the door panel.
• Reassemble the door trim, verify operation of all functions and ensure no rattle or obstruction.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C3 II (A51) 2009-2016
• Product Codes: 96637535XT, 98012514XT, 6490CJ
• Other Numbers: A51

Common Failure Modes And Lifespan

Window switches are subject to repeated mechanical and electrical stress. Typical causes of failure include:

• Wear Of Internal Contacts: Repeated cycles can erode contact surfaces, causing intermittent or non-functional switch operation.
• Moisture Ingress And Corrosion: Water or humidity entering the door can corrode connectors or switch internals.
• Mechanical Damage: Broken actuator tabs or cracked plastic bezels from forceful operation or during removal/installation.
• Contaminants And Dirt Build-Up: Dust and debris in the switch mechanism can impede proper contact and movement.

Expected service life varies with use and environment; many switches remain functional for 8–15 years, but high-mileage or heavily used vehicles may require earlier replacement.

Recommendations For Installation

• Always disconnect the battery before removing the switch to avoid short circuits and accidental window movement.
• Use proper trim tools to prevent damage to door panels and retainers.
• Inspect connectors and wiring for corrosion or broken wires when replacing the switch; repair any wiring faults to prevent repeat failures.
• Test all window functions, including any auto-up/auto-down features, before reassembling the door panel.

Reason This Part Most Often Fails

Most failures are caused by contact wear and moisture-related corrosion. Repeated switching cycles gradually degrade the electrical contacts, while water ingress or condensation can accelerate corrosion and lead to intermittent or complete loss of function. Physical damage during previous repairs or panel removal is another common cause.

This replacement window and mirror control switch is designed for Citroën C3 II models (2009–2016). It provides reliable control of driver and passenger windows with comfort one-touch functionality and operates electrically adjustable and folding exterior mirrors. Built to fit the original mounting points and electrical connectors, the unit is intended for mechanics and experienced DIYers looking for a direct-fit solution to restore central window and mirror functions.

Key Benefits

• Direct replacement for the original switch assembly, preserving factory ergonomics and functionality.
• Comfort one-touch window operation for improved convenience during driving.
• Integrated controls for electrically adjustable and electrically folding mirrors.
• Suitable for garage technicians and competent DIY installers — straightforward swap with standard tools.

Function And Typical Use

The switch assembly controls the power windows (including one-touch/comfort operation) and mirror adjustment and folding. It interfaces with the vehicle wiring harness via the factory connector and communicates mirror positions to the mirror motors. On models equipped with mirror folding, the switch sends the folding command to the relevant motor/relay circuit.

How The Part Is Replaced

• Prepare: Park the vehicle on a level surface, engage the handbrake and remove the ignition key.
• Safety: Disconnect the negative battery terminal before starting to avoid short circuits and to protect vehicle electronics.
• Access: Remove the door trim/panel to reach the switch—this commonly requires removal of trim clips and a few screws. Use appropriate trim tools to avoid damaging plastic clips.
• Remove Old Unit: Pry out the switch bezel, unscrew any fasteners, and unplug the electrical connector(s).
• Install New Unit: Connect the wiring harness to the replacement switch, secure the switch into the bezel, and re-fit the door trim in reverse order.
• Test: Reconnect the battery, verify window one-touch operation, mirror adjustment and folding function before final assembly.
• Tools Recommended: Trim removal tool, Torx/Phillips screwdrivers, socket set, and multimeter for electrical checks if needed.

Installation Recommendations

• Always Disconnect The Battery Before Working On Electrical Components To Prevent Short Circuits And Possible Damage.
• Handle The Switch Connector Carefully—Bent Pins Or Damaged Clips Can Cause Poor Contact.
• When Removing Door Trim, Keep Track Of Fasteners And Clips To Ensure Correct Reassembly.
• If Mirror Folding Or Window Functions Do Not Operate After Fitment, Re-check Connectors And Fuses Before Replacing The Switch.

Most Common Failure Reasons

• Wear Of Internal Contact Surfaces From Frequent Use Leading To Intermittent Operation.
• Moisture Ingress Or Corrosion, Especially In Older Vehicles Or Where Door Seals Are Compromised.
• Broken Plastic Clips Or Mechanical Damage During Door Trim Removal/Reinstallation.
• Faulty Solder Joints Or Connector Problems Causing Loss Of Electrical Continuity.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 II (2009–2016)
• Product Codes: 96652236XT, 6490AZ
• Additional Numbers: 96652236 XT; 6490 AZ

This switch is intended as a replacement part for the specified model years. It restores driver controls for windows and mirrors to factory-style operation when fitted correctly by a competent technician or experienced DIYer.

High-quality replacement window control for Peugeot 307 (2005–2007) with original part codes 96498421XT and 6554KT. Ideal for professional mechanics and experienced DIY enthusiasts who need a reliable, ready-to-install unit. The switch operates power window circuits on the relevant door and is a common spare part for vehicles showing intermittent or failed window operation. Listing part numbers prominently increases findability in searches for Peugeot 307 window switch 96498421XT 6554KT.

Key Features

• Direct-fit unit for Peugeot 307 (2005–2007) carrying original product codes 96498421XT and 6554KT.
• Used part Showing Signs Of Use But Fully Functional.
• Plugs into original wiring harness — no modification required when compatible.
• Common spare for replacing worn or intermittent door window switches.

Function And Common Failure Causes

This switch controls the electric window motor circuits for the door in which it is installed. Typical failure modes include worn internal contacts from prolonged use, contamination from dirt or moisture, broken actuator buttons or mounting clips, and oxidation of electrical terminals. Symptoms of a failing unit are intermittent window movement, windows working only in one direction, stuck buttons, or complete loss of function on the affected door.

Installation Recommendations

Recommended for fitment by a trained technician or an experienced DIYer. Typical replacement steps:

• Remove the interior door trim using appropriate trim tools to avoid damage to clips and upholstery.
• Disconnect the vehicle battery before starting work to prevent short circuits and protect vehicle electronics.
• Unplug the switch connector and remove any retaining screws or clips holding the switch module in place.
• Swap the switch into the trim bezel or replace the entire module, then reconnect the wiring harness and reassemble the door trim.
• Verify operation of the window(s) and any related functions (e.g., child lock) after reassembly.

Useful tools: trim removal set, Torx/Phillips screwdriver set, multimeter for continuity checks, and a flashlight. If electrical faults persist after replacement, check wiring, grounds, fuses, and the window motor.

Why Parts Fail Most Often

The most common reasons for failure are mechanical wear of the switch contacts due to frequent use, ingress of moisture or dirt causing corrosion, and physical damage to buttons or mounting points. Environmental exposure and high-cycle usage (daily frequent window operation) accelerate wear.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307 (2005–2007)
• Product Codes: 96498421XT, 6554KT
• Additional Numbers: Not Provided

Notes For Buyers

Part Numbers Are Included To Help You Confirm Fitment. This Is A Used Unit Showing Signs Of Use But Confirmed Functional. Suitable For Workshops And Self-Repair Enthusiasts Seeking An OEM-Code Match For Peugeot 307 Window Problems.

Product Overview

High-quality used driver door switch assembly designed for Citroën C4 II (B7) and DS4 models. This unit operates the driver’s window and provides mirror adjustment control (and mirror folding where the vehicle is equipped). Ideal for mechanics and DIY enthusiasts looking for a direct-fit replacement with original equipment (OE) references. Frequently searched by part numbers 96657055ZD and 6490JW.

Why Choose This Switch

• Direct Fit For Citroën C4 II (B7) And DS4 Driver Door Applications.
• Original Equipment Style Functionality For Smooth Window And Mirror Control.
• Used Unit In Fully Functional Condition — Cost-Effective Alternative To New Parts.
• Commonly Identified By OE Codes 96657055ZD And 6490JW, Making It Easy To Find.

Technical Information

• Manufacturer: Stellantis (Citroën)
• Model(s): Citroën C4 II (B7), DS4 — Driver Door
• Product Codes: 96657055ZD, 6490JW
• Additional Numbers: HZD- (Color Code) — Black Mistral

Function And Typical Failure Modes

This module controls the electric window motor for the driver’s side and the electric mirror adjustment; on some vehicles it also controls mirror folding and central locking signals. Failures typically occur due to normal wear of the microswitch contacts, contamination from moisture or dirt, or mechanical wear of the rocker/button assemblies. Intermittent operation or complete loss of function are the usual symptoms. Poor electrical connection at the connector or corroded pins can also cause faults.

Expected Service Life

Service life depends on use and environment. With regular use and normal conditions these switch assemblies commonly remain serviceable for many years; heavy daily use or exposure to moisture and dirt accelerates wear. Typical useful life often ranges across many years (commonly cited in practice as around 8–15 years depending on vehicle use and maintenance).

Installation Recommendations

• Disconnect The Battery Before Starting Work To Avoid Short Circuits And Prevent Damage To Vehicle Electronics.
• Remove The Door Panel Carefully: Pry Off Trim Clips Gently, Unscrew Fixings, And Release The Panel From The Door Frame Without Forcing Plastic Tabs.
• Unplug The Electrical Connector(s) From The Switch Assembly And Remove Mounting Screws Or Clips Holding The Unit In Place.
• Fit The Replacement Switch, Reconnect The Connector(s) Securely, And Reassemble The Door Panel.
• After Reinstallation, Reconnect The Battery And Test All Functions: Window Up/Down, Mirror Adjustment, And Folding (If Equipped).
• Check For Smooth Mechanical Movement And Stable Electrical Operation; Clean Connector Pins If Corrosion Is Present.

Most Common Reason For Failure

The Most Frequent Cause Of Failure Is Wear Of Internal Switch Contacts And Contamination (Moisture/Dirt). Repeated Use Leads To Contact Pitting And Mechanical Degradation Of Buttons, Which Results In Intermittent Or Non-Functional Controls. Damaged Wiring Or Connector Corrosion Are Secondary Common Causes.

Compatibility And Fitment Notes

Fits Driver Door Applications On Citroën C4 II (B7) And DS4 Models Corresponding To The Listed OE Codes. Always Verify The Part Numbers Printed On The Unit Against Your Vehicle’s Existing Part To Ensure Direct Compatibility.

Additional Advice

When replacing a used switch, inspect the door harness and connector for corrosion or damaged wires. If windows or mirrors behave unpredictably after swap, recheck connector seating and ground continuity. For complex electrical faults, a wiring diagnosis by a professional may be necessary.

This power window switch, marked with part numbers 96360166XT and 6554E8, is a direct-fit replacement option for many Peugeot 307 and Peugeot 407 door applications. Designed for technicians and DIY enthusiasts, the switch restores reliable window control when the original unit fails. It is commonly used in front door assemblies and integrates with the standard 12V vehicle electrical system found on Stellantis-built Peugeot and Citroën models.

Technical Information

• Manufacturer: Stellantis / Peugeot / Citroën
• Model: Peugeot 307, Peugeot 407
• Product Codes: 96360166XT, 6554E8
• Additional Numbers: 655400000000

How To Replace

Replacement is straightforward for a competent automechanic or an experienced DIYer. Basic steps:

• Disconnect the negative battery terminal to avoid short circuits and accidental window operation.
• Remove the interior door trim or switch bezel (clips and screws vary by model).
• Release the switch module from the door panel and unplug the electrical connector.
• Install the new switch by connecting the harness, seating the module, and refitting the bezel and trim.
• Reconnect the battery and test all window functions before final reassembly.

Installation Recommendations

• Use plastic trim tools to avoid damaging the door panel or clips.
• Check connector pins for corrosion or bent terminals; clean contacts if necessary.
• Apply a small amount of dielectric grease to terminals to reduce future corrosion in humid environments.
• Test the switch operation through full travel after installation and before fully refitting trim.

Common Failure Causes

Power window switches typically fail due to wear on internal contacts, moisture ingress, or mechanical damage to the buttons and housing. Frequent use, spilled liquids, or dirt and contamination in the door environment accelerate contact erosion and intermittent operation. In some cases, related wiring issues or faulty window motors can be mistaken for a bad switch, so verify system function during diagnosis.

Expected Lifetime And Symptoms

Lifetime depends on usage and exposure—many switches remain functional for several years, but heavy daily use or exposure to moisture can cause failure in a shorter time. Typical symptoms indicating replacement is needed include intermittent window movement, only one or two positions responding, sticky or loose buttons, and audible arcing or burning smell from the switch area.

Searchable By Part Number: 96360166XT, 6554E8 — customers often locate this part using these codes for Peugeot 307 and 407 models.

This sunroof blind controller is a direct-fit interior switch for Peugeot 407 and Citroën C3 models. Designed for workshop use and competent DIYers, the unit allows smooth operation of the sliding sunshade (interior blind) and is commonly searched by its part numbers 96413719BJ and 6554Q3. The compact design matches the original trim appearance and the Color FBJ – LAMA corresponds to the vehicle interior trim code.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Peugeot 407, Citroën C3
• Product Codes: 96413719BJ, 6554Q3
• Other Numbers: NFP, Color Code FBJ – LAMA

Function And Application

The controller operates the electric sunroof blind (interior sunshade) by sending the command to the blind motor or mechanism. It is mounted in the roof console or overhead trim and integrates with the vehicle’s interior electrical system. Use this part when the sunshade does not move, moves intermittently, or when the control switch has worn contacts or broken actuator buttons.

How To Replace

Suitable for experienced mechanics and able DIYers. General replacement steps:

• Disconnect the negative battery terminal before starting to avoid short circuits.
• Carefully remove the overhead console or headliner trim surrounding the switch using plastic trim tools to avoid damage to clips and upholstery.
• Unscrew the switch module fasteners and unplug the electrical connector(s).
• Fit the new controller, connect the wiring harness, and secure fasteners. Reinstall trim and reconnect the battery.
• Test full range of sunshade travel and switch functions after installation.

Installation Recommendations

• Work On A Cool Interior: Sunroof trim and plastic clips are easier to handle at moderate temperatures.
• Use Trim Tools: Protect the headliner and decorative trim with plastic pry tools to avoid cracking or scuffing.
• Check Connector Pins: Inspect connectors for corrosion or bent pins before fitting the new unit.
• Reset Procedures: After installation, operate the blind through full travel to ensure correct indexing; consult vehicle service manual for any calibration steps if needed.

Why This Part Commonly Fails

Most frequent causes of failure include worn internal switch contacts from repeated use, ingress of dust or moisture into the overhead console, brittle plastic actuator parts or housing that crack with age, and intermittent electrical connection due to connector corrosion. Excessive force or misuse when operating the blind can also accelerate wear. Address the root cause (for example, moisture ingress) to avoid repeated failures.

This power window switch is designed for Citroën small models and is a common replacement part for workshop repairs and DIY restorations. It controls the electric window movement with sequential (one-touch/auto-return) functionality, allowing smooth opening and closing of the window glass. The switch is frequently searched by its product numbers, so listing the codes in the description helps technicians and owners find the correct unit quickly.

Application And Function

The unit is intended for front door window control on Citroën C2, Citroën C3 and Citroën C3 Pluriel models that use sequential window operation. It functions as the user interface for the window motor: pressing the appropriate rocker or button sends the command to the window regulator to move the glass up or down, with the sequential/one-touch feature completing the full travel automatically when activated.

Replacement Procedure

Replacement is straightforward for trained technicians and experienced DIYers. Typical steps:

• Disconnect the negative battery terminal to avoid short circuits.
• Remove the door trim panel: release clips and remove screws around the armrest and handle area.
• Unplug the electrical connector from the old switch and release any retaining clips or screws.
• Install the new switch, reconnect the wiring and reassemble the door trim in reverse order.
• Verify operation of the window in both directions and check the sequential/one-touch function.

Why The Part Usually Fails

Failures are most often caused by wear of internal electrical contacts from frequent use, ingress of moisture or dirt, and mechanical wear of the plastic actuators. Symptoms include intermittent operation, only partial travel, or complete loss of control for the affected window. Poor electrical connections or damaged wiring in the door loom can also mimic switch failure and should be checked during diagnostics.

Installation Recommendations

• Always isolate the battery before starting electrical work.
• Inspect door wiring and connectors for corrosion or damage while the trim is removed.
• Use gentle prying tools to avoid breaking plastic clips on the door panel.
• After fitting, calibrate any automatic window functions according to the vehicle service procedures if required.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C2, Citroën C3, Citroën C3 Pluriel
• Product Codes: 96401469XT
• Other Numbers: 6554L7

Searchable product numbers and clear model listing make this description useful for workshops and independent mechanics looking for the correct replacement switch. The switch is a direct-fit service part for compatible Citroën models and restores normal window control when fitted correctly.

Part description

This window and mirror control is designed for PSA Citroën/Peugeot cars and comes with frame. It is a practical part for quick repair of malfunctioning window or mirror controls, including the function of electric folding mirrors. Thanks to the listed codes, you can easily find it even when searching by product number.

• Design: controller + frame
• Functions: window control, mirror control, electric mirror folding

Technical information

• Manufacturer: PSA Citroën Peugeot
• Model: Peugeot 308 T9 (as described); the controller itself without a frame can also be used on Citroen C4 SPACETOURER, C4 PICASSO 2014, C5 AIRCROSS, Peugeot 3008 and 5008
• Other numbers: 98031623ZD (frame)

Product codes

• Product codes: 98319761ZD, 98031623ZD

Installation recommendations

• Check that the part codes (98319761ZD) and frame (98031623ZD) match your original part before assembly.
• It is recommended to perform a visual inspection of the connectors and fixings (latches/packs) so that everything fits correctly in the door panel.
• After installation, check the functions: window control, mirror adjustment and electric folding mirrors.

Reasons why the part is damaged

• Mechanical wear of buttons and contacts during frequent use.
• Intrusion of moisture into the door (leakage, condensation) and subsequent corrosion of the contacts.
• Damage to the connector or wiring in the door (breaking wires in the grommet).
• Reckless disassembly/assembly – cracked frame handles or damaged latches.