Description

Direct-fit replacement passenger window switch designed for Citroën C3 II (2009–2016). This OE-compatible switch restores reliable control of the front passenger window with the original look and tactile feedback. Finished in Cornelie Black (FXT), it is intended for the front passenger side control panel and is suitable for both professional workshops and competent DIYers who perform interior trim work.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 II (A51) 2009–2016
• Product Codes: 96637533XT, 98012512XT
• Additional Numbers: 6490CG, A51

Compatibility And Fitment

Compatible with Citroën C3 II models produced between 2009 and 2016. Matches original mounting points and electrical connector pinout used in standard C3 II passenger door switch assemblies. Always verify part numbers against vehicle paperwork or door switch stamping where available.

How The Part Is Replaced

Replacement is straightforward for a trained technician or experienced DIYer. Typical procedure:

• Remove the interior door handle trim and door card using suitable trim tools to avoid damaging clips.
• Carefully pry out the old switch module from the door armrest bezel.
• Disconnect the electrical connector(s) from the old switch and inspect for corrosion or damaged pins.
• Fit the new switch, connect the wiring harness, and test window operation before reassembling the door card.
• Reinstall trim pieces and ensure all clips are properly seated.

Installation Recommendations

• Disconnect The Vehicle Negative Battery Terminal Before Working On Electrical Components.
• Use Proper Trim Tools To Avoid Breaking Door Panel Clips And Plastic Retainers.
• Inspect Connector Pins And Wiring For Corrosion Or Damage; Clean Contacts If Necessary.
• Test The Switch Operation And Window Function Before Fully Reassembling The Door Panel.
• If Window Still Does Not Operate Smoothly, Check The Window Regulator And Motor To Avoid Replacing The Switch Unnecessarily.

Why The Part Fails Most Often

Window switches typically fail due to wear of internal electrical contacts from frequent use, ingress of moisture or dirt, and liquid spills that corrode contacts. Mechanical wear or physical impact to the switch bezel and buttons can also cause malfunction. In some cases, repeated attempts to operate a jammed window place extra load on the switch and lead to premature failure.

Notes For Mechanics And DIY Enthusiasts

Designed To Meet The Expectations Of Professional Workshops While Remaining Accessible For Competent Home Mechanics. The switch offers a cost-effective fix for intermittent or non-functioning passenger window controls and is a common service item during door trim or electrical repairs. Keep the connector clean and secure during installation to ensure long-term reliability.

Order this Citroën C3 II front passenger window switch by referencing product codes 96637533XT / 98012512XT / 6490CG for fast identification and correct fitment.

Product Overview

High-quality replacement power window switch designed for Citroën C3 II (A51) produced between 2009 and 2016. This unit is suitable for use in both the driver and front passenger doors and carries OEM cross-references used by Stellantis for Citroën and Peugeot vehicles. The control offers reliable actuation of the window regulator and fits original mounting points for straightforward installation.

Why Choose This Window Switch

• Direct fit for Citroën C3 II models 2009–2016, minimizing adaptation time.
• OEM cross-reference numbers included to simplify part identification.
• Designed for professional garages and DIY mechanics who need a robust, serviceable switch.
• Black Cornelie finish (FXT) matches original interior trim styling.

Installation

Replacing the window switch is a routine repair for garages and experienced DIYers. Typical procedure:

• Disconnect the vehicle battery before starting to prevent short circuits and inadvertent operation.
• Carefully remove the door trim panel or the switch trim bezel (depending on trim level) using appropriate trim tools to avoid damaging clips and door card finish.
• Unplug the electrical connector from the old switch and release any retaining clips.
• Remove the old switch and install the new unit, ensuring correct orientation and secure locking of retaining clips.
• Reconnect the connector and briefly reconnect the battery to test switch function (up/down, auto functions if present) before refitting the door panel.
• Reassemble the door trim, verify operation of all functions and ensure no rattle or obstruction.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C3 II (A51) 2009-2016
• Product Codes: 96637535XT, 98012514XT, 6490CJ
• Other Numbers: A51

Common Failure Modes And Lifespan

Window switches are subject to repeated mechanical and electrical stress. Typical causes of failure include:

• Wear Of Internal Contacts: Repeated cycles can erode contact surfaces, causing intermittent or non-functional switch operation.
• Moisture Ingress And Corrosion: Water or humidity entering the door can corrode connectors or switch internals.
• Mechanical Damage: Broken actuator tabs or cracked plastic bezels from forceful operation or during removal/installation.
• Contaminants And Dirt Build-Up: Dust and debris in the switch mechanism can impede proper contact and movement.

Expected service life varies with use and environment; many switches remain functional for 8–15 years, but high-mileage or heavily used vehicles may require earlier replacement.

Recommendations For Installation

• Always disconnect the battery before removing the switch to avoid short circuits and accidental window movement.
• Use proper trim tools to prevent damage to door panels and retainers.
• Inspect connectors and wiring for corrosion or broken wires when replacing the switch; repair any wiring faults to prevent repeat failures.
• Test all window functions, including any auto-up/auto-down features, before reassembling the door panel.

Reason This Part Most Often Fails

Most failures are caused by contact wear and moisture-related corrosion. Repeated switching cycles gradually degrade the electrical contacts, while water ingress or condensation can accelerate corrosion and lead to intermittent or complete loss of function. Physical damage during previous repairs or panel removal is another common cause.

This replacement window and mirror control switch is designed for Citroën C3 II models (2009–2016). It provides reliable control of driver and passenger windows with comfort one-touch functionality and operates electrically adjustable and folding exterior mirrors. Built to fit the original mounting points and electrical connectors, the unit is intended for mechanics and experienced DIYers looking for a direct-fit solution to restore central window and mirror functions.

Key Benefits

• Direct replacement for the original switch assembly, preserving factory ergonomics and functionality.
• Comfort one-touch window operation for improved convenience during driving.
• Integrated controls for electrically adjustable and electrically folding mirrors.
• Suitable for garage technicians and competent DIY installers — straightforward swap with standard tools.

Function And Typical Use

The switch assembly controls the power windows (including one-touch/comfort operation) and mirror adjustment and folding. It interfaces with the vehicle wiring harness via the factory connector and communicates mirror positions to the mirror motors. On models equipped with mirror folding, the switch sends the folding command to the relevant motor/relay circuit.

How The Part Is Replaced

• Prepare: Park the vehicle on a level surface, engage the handbrake and remove the ignition key.
• Safety: Disconnect the negative battery terminal before starting to avoid short circuits and to protect vehicle electronics.
• Access: Remove the door trim/panel to reach the switch—this commonly requires removal of trim clips and a few screws. Use appropriate trim tools to avoid damaging plastic clips.
• Remove Old Unit: Pry out the switch bezel, unscrew any fasteners, and unplug the electrical connector(s).
• Install New Unit: Connect the wiring harness to the replacement switch, secure the switch into the bezel, and re-fit the door trim in reverse order.
• Test: Reconnect the battery, verify window one-touch operation, mirror adjustment and folding function before final assembly.
• Tools Recommended: Trim removal tool, Torx/Phillips screwdrivers, socket set, and multimeter for electrical checks if needed.

Installation Recommendations

• Always Disconnect The Battery Before Working On Electrical Components To Prevent Short Circuits And Possible Damage.
• Handle The Switch Connector Carefully—Bent Pins Or Damaged Clips Can Cause Poor Contact.
• When Removing Door Trim, Keep Track Of Fasteners And Clips To Ensure Correct Reassembly.
• If Mirror Folding Or Window Functions Do Not Operate After Fitment, Re-check Connectors And Fuses Before Replacing The Switch.

Most Common Failure Reasons

• Wear Of Internal Contact Surfaces From Frequent Use Leading To Intermittent Operation.
• Moisture Ingress Or Corrosion, Especially In Older Vehicles Or Where Door Seals Are Compromised.
• Broken Plastic Clips Or Mechanical Damage During Door Trim Removal/Reinstallation.
• Faulty Solder Joints Or Connector Problems Causing Loss Of Electrical Continuity.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 II (2009–2016)
• Product Codes: 96652236XT, 6490AZ
• Additional Numbers: 96652236 XT; 6490 AZ

This switch is intended as a replacement part for the specified model years. It restores driver controls for windows and mirrors to factory-style operation when fitted correctly by a competent technician or experienced DIYer.

The original electric windows and mirrors for the driver’s door designed for the Citroën C3 II (2009–2016). This is a part of the PSA concern with OEM codes 96637530XT / 98012283XT / 6490ce. Color FXT – black cornielia. Suitable as a direct replacement for a non -functional panel when they do not control windows or rear -view mirrors, or it is stuck.

This panel ensures complete control of electric windows on the car and setting the exterior rear -view mirrors (including heating and possible electric folding according to the equipment of the car). With the match of the Part code, the plug & play installation is without the need for installation adjustment. In older C3 II, microswitches and contacts often leave due to moisture in the door and normal wear – a typical manifestation is a random function of the buttons, a non -functional automatic driver of the driver’s window, or the inability to adjust the mirror.

We recommend to verify compatibility according to the OEM code in the old part or by VIN. It is important to compare the shape of the connector and the equipment of the car (the presence of mirror folding, the number of controlled windows). The FXT color code (Noir Cornélie) ensures that the panel fits in the interior.

Installation – a brief procedure
– Turn off the ignition, recommend disconnect minus the battery pole.
– Carefully click the panel from the handles/frame in the driver’s door using the plastic lever.
– Disconnect the electrical connector/y, put the new panel and click the/y connector.
– Click back into the frame and test the function of all windows and mirrors.

Condition: The part used, can bear common signs of use (abrasions on buttons, hair scratches). The functionality corresponds to the description and photographs of a particular piece. The ideal solution to quickly restore full control of windows and mirrors without unnecessary costs.

The most common symptoms of a defective driver
– It is not possible to run/raise the driver’s window or passengers from the driver panel.
– cannot be set or switching left/right mirror, non -functional heating.
– Drawn outages of buttons, random reactions to press.

technical information

• Manufacturer: PSA (Citroën / Peugeot)
• Model: Citroën C3 II, Year of Manufacturing 2009–2016, Location: Driver’s doors
• Product codes: 96637530XT; 98012283XT; 6490ce
• Other numbers: color code FXT – black cornielia (noir cornielia); 9663 7530 XT / 9801 2283 XT (alternative notes)

Original passenger window controller (front right door) for Citroën C3 II (2009–2016). It is a part of the dog’s vehicle, fully functional, with common traces of use. FXT – black cornielia, so in design and dimensions fits exactly into the original door panel.

Looking for a quick and certain solution of the non -functioning window download button? This original switch is an ideal replacement without the need for modifications. Compared to universal alternatives, it guarantees the proper functioning of the lighting, the correct response of the buttons and the compatibility with electronic doors for C3 II. The codes 96657927XT and 6490CH (PSA) are used to trace and verify conformity.

Why the part changes: the most common defects include oxidation or wear of contacts (often after water root), mechanical damage to the button or interrupting internal joints. This is manifested by a delayed reaction, complete inoperative direction up/down or intermittent running the window.

The mounting is simple and fast: turn off the ignition, carefully pierced the plastic bar/control frame in the hand door, disconnect the multi -pin connector, click the new driver and re -connect the connector. After assembly, we recommend testing the function of the window; For versions with automatic range, simple calibration may be needed (completion of the full stroke and downhill of the window with the button).

technical information

• manufacturer: dog/Citroën
• Model: Citroën C3 II (A51), 2009–2016, front right door – passenger
• product codes: 96657927XT, 6490CH
• additional numbers: 9657927XT; FXT color code – black cornielia

Conformity verification tip: Compare the numbers on your original controller (typically 96657927XT) and the color of the frame. If the numbers agree, the “plug and play” assembly is without coding.