Product Overview

High-quality parking sensor designed for Citroën and Peugeot vehicles. Ideal for professional workshops and DIY mechanics needing a reliable PDC (Park Distance Control) replacement. The unit is compatible with vehicles using PSA/Stellantis electrical architecture and is commonly referenced by the part numbers listed below. Color code HZE corresponds to Tramontane finish, matching specific bumper paints.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën, Peugeot (Commonly Used On: PEUGEOT 3008 I, PEUGEOT 5008 I)
• Product Codes: 9677782977, 9677782980, 6590JE
• Other Numbers: HZE (Color Code TRAMONTANE)

Function

The sensor is an ultrasonic parking aid element that detects obstacles near the vehicle bumper and sends distance information to the PDC control module. It helps the driver when maneuvering at low speeds by triggering audible alerts or dash indicators.

Replacement Procedure

Designed for straightforward replacement by experienced technicians. Typical replacement steps:

• Prepare Tools: Trim removal tools, screwdriver set, multimeter for basic electrical checks, protective gloves.
• Safety First: Disconnect the battery before starting work to prevent short circuits and protect vehicle electronics.
• Access Sensor: Remove the rear bumper trim or access panel to reach the sensor from behind the bumper. On some models the sensor can be removed through inner wheel arch liners or luggage compartment trims.
• Disconnect Connector: Release the electrical connector and remove the sensor retaining clip or housing.
• Fit New Sensor: Insert the new sensor ensuring correct orientation and secure locking. Replace the sealing rubber if available and required for watertight fitment.
• Electrical Check: Reconnect battery and test the sensor operation before full reassembly. Verify PDC warning tones and dashboard indicators are functioning.
• Final Assembly: Refit trims and bumper panels after successful functional test.

Installation Recommendations

• Ensure The Sensor Sits Flush: Proper seating in the bumper cutout prevents false readings. Use the correct retaining clips and, if provided, the sealing ring to avoid water ingress.
• Test Before Reassembly: Always test functionality with the bumper temporarily secured to avoid repeated removal.
• Protect Connectors: Clean mating surfaces and apply dielectric grease if necessary to prevent corrosion on electrical contacts.
• Use Correct Color Code: Match The Color Code HZE (Tramontane) for painted bumpers to avoid visible mismatch.

Most Common Failure Reasons

• Water Ingress: Damaged or missing sealing ring allows moisture to enter the sensor housing and corrode internal components.
• Impact Damage: Bumper collisions or knocks can physically damage the sensor element or its mounting.
• Connector And Wiring Issues: Corroded connectors, pin damage or wiring faults cause intermittent operation or total failure.
• Dirt And Contamination: Heavy buildup of mud, ice or road debris on the sensor face leads to incorrect or no detection.
• Ageing Electronics: Over time, the ultrasonic transducer or internal electronics may degrade, especially in vehicles used in harsh environments.

Notes For Professionals

When replacing sensors, always verify part numbers and color codes to ensure correct fit and finish. Some vehicle systems may require a quick functional check with diagnostic tools to confirm proper integration with the PDC control unit. For a lasting repair, replace damaged seals and inspect wiring harnesses for hidden damage after an impact.

Keywords

Parking Sensor, PDC Sensor, Citroën Parking Sensor, Peugeot Parking Sensor, 9677782977, 9677782980, 6590JE, HZE, Tramontane, PEUGEOT 3008 I, PEUGEOT 5008 I

High-quality replacement parking sensor designed for Citroën and Peugeot PDC systems. This black, unpainted sensor restores reliable obstacle detection for parking assistance, making it a practical choice for professional workshops and DIY mechanics. Commonly referenced by OEM numbers, the unit offers straightforward fitment and helps eliminate false warnings or intermittent operation caused by damaged or corroded original sensors.

Key Benefits

• Direct Replacement: Fits Original Equipment locations on Compatible Citroën and Peugeot Bumpers.
• Reliable Detection: Restores Proper Ultrasonic Sensing For Parking Assistance Systems.
• Economical Solution: Ideal For Quick Repair Jobs In Garages Or Home Workshops.
• Unpainted Finish: Ready For Bodyshop Painting If Required To Match Vehicle Colour.

Compatibility

Compatible With Various Citroën And Peugeot PDC Systems. Known Fitment Includes:

• Peugeot 3008 I
• Peugeot 5008 I
• Other Citroën And Peugeot Models Using The Listed Product Codes

How The Part Works

The sensor is an ultrasonic parking proximity sensor used by the vehicle’s Park Distance Control (PDC) system. It emits and receives sound pulses to measure the distance to nearby obstacles and reports signals to the parking control unit, which then provides audio/visual feedback to the driver.

Replacement Procedure

Typical Replacement Steps (Suitable For Experienced DIYers And Professional Technicians):

• Access The Sensor From Behind The Bumper Or Through The Wheel Arch Trim Depending On Model.
• Carefully Disconnect The Electrical Connector And Release The Sensor Retaining Clips Or Grommet.
• Remove The Old Sensor And Inspect The Mounting Hole And Wiring For Corrosion Or Damage.
• Fit The New Sensor Into The Bumper, Ensure Any Sealing Grommet Is Present Or Replaced, And Reconnect The Electrical Connector.
• Secure Trim Pieces And Perform A System Check: Most Replacements Are Plug-And-Play; If Fault Codes Appear, Clear Using A Diagnostic Tool And Re-Test.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën / Peugeot (See Product Codes For Exact Fitment)
• Product Codes: 9664027977, 9677782980, 6590JE
• Additional Numbers: (6590.JE)
• Color: Black — Unpainted
• Sealing Rubber: May Not Be Included

Recommended Tools And Tips

• Plastic Trim Tools To Avoid Damaging Bumper Trim.
• Basic Hand Tools For Removing Fasteners And Wheel Arch Liners.
• Multimeter Or Diagnostic Scanner To Verify Power And Communication If Problems Persist.
• If The Sealing Grommet Is Missing Or Damaged, Replace It During Installation To Prevent Water Ingress.

Why Sensors Fail

Parking Sensors Commonly Fail Due To:

• Water Ingress Or Corrosion Around The Connector Or Sensor Housing (Especially If Sealing Grommet Is Missing).
• Mechanical Damage From Impacts Or Road Debris.
• Connector Or Wiring Harness Faults Causing Intermittent Operation.
• Contamination On The Sensor Surface (Dirt, Mud, Salt) Leading To False Readings.

Final Notes

This sensor Is Intended As A Direct Replacement Part For The Listed Product Codes. For A Durable Repair, Inspect The Sealing Grommet And Wiring When Replacing The Sensor, And Repaint The Unpainted Surface If A Color-Matched Finish Is Required. Add The Item To Your Cart To Restore Reliable Parking Assistance Quickly And Cost-Effectively.

High-quality parking sensor (PDC) designed for Stellantis Citroën and Peugeot models. Ideal for professional workshops and experienced DIY mechanics who require a reliable replacement part identified by OE numbers 9677783280, 9677782980 or reference 6590JE. The sensor restores parking aid functionality, reduces the risk of minor collisions when maneuvering and is a common spare for first‑generation Peugeot 3008 and 5008 vehicles. Fits into standard rear bumper housings and is optimized for vehicle body color EZRC Grey Aluminium.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Peugeot 3008 I; Peugeot 5008 I (Common Application)
• Product Codes: 9677783280; 9677782980
• Other Numbers: 6590JE

Function

This ultrasonic parking sensor detects obstacles behind the vehicle and communicates distance information to the parking aid control unit (PDC/EZRC). The system warns the driver with progressive beeps or visual indicators as the vehicle approaches an object, helping avoid low‑speed impacts during reversing and parking maneuvers.

Replacement Procedure

Typical replacement steps for rear bumper sensors:

• Disconnect The Battery Or At Least Ensure The Vehicle Is Electrically Isolated Before Starting Work.
• Access The Sensor From The Bumper Inner Liner Or After Removing The Rear Bumper Depending On Vehicle Configuration.
• Unplug The Electrical Connector And Release The Sensor From Its Retaining Clip Or Housing.
• Inspect And Replace The Sealing Grommet If Missing Or Damaged (Sealing Rubber May Not Be Included).
• Install The New Sensor Ensuring Correct Orientation And Firm Seating In The Bumper Aperture.
• Reconnect The Connector, Refit All Panels, Reconnect The Battery And Test The Parking Aid Functionality.

Installation Recommendations

• Use A Diagnostic Tool To Verify Sensor Signal And Live Data Where Possible — This Saves Time Identifying Wiring Or Module Issues.
• Always Replace The Sealing Grommet If It Is Missing Or Worn To Prevent Water Ingress.
• Clean The Bumper Mounting Area Before Fitting To Ensure Proper Seal And Sound Propagation.
• Handle The Sensor Connector Carefully To Avoid Bent Pins Or Corrosion; Apply Dielectric Grease If Appropriate.
• After Installation, Perform A System Check By Activating Reverse Gear And Monitoring For Consistent Beep Pattern And No Error Messages.

Why The Part Most Often Fails

Common causes of parking sensor failure include:

• Water Ingress And Corrosion Due To Damaged Or Missing Sealing Grommets.
• Physical Damage From Impacts, Scratches Or Deformation During Minor Collisions.
• Contamination By Dirt, Road Salt Or Paint Overspray That Alters Ultrasonic Signal Transmission.
• Connector Corrosion Or Wiring Faults Leading To Intermittent Communication With The PDC Module.
• Ageing Electronics And Moisture‑Related Failures In Harsh Climates.

Notes For Professionals

When replacing sensors as part of diagnostic work, always consider the condition of harnesses and the PDC control unit. Replacing a single sensor often restores function, but intermittent faults may point to wiring or module issues that require further troubleshooting with a suitable PSA diagnostic tool.

Product Overview

High-quality Bosch parking sensor designed for Stellantis group vehicles, commonly fitted to Citroën and some Peugeot models. The sensor restores reliable ultrasonic detection for the Park Distance Control (PDC) system, helping mechanics and DIY enthusiasts diagnose and replace faulty sensors quickly. Ideal for workshops and independent repairers who prefer genuine-equivalent components identified by OEM reference numbers.

Benefits

• Direct replacement for original front or rear PDC sensors that share the listed OEM codes.
• Restores accurate obstacle detection and audible/visual warnings, improving safety during low-speed maneuvers.
• Easy to fit in the bumper opening used by the original sensor — no bodywork modification required when matching the correct code.

Technical Information

• Manufacturer: Bosch
• Model: Citroën C4 Picasso, Citroën C5 (also used on compatible Peugeot models sharing these part numbers)
• Product Codes: 9649614177XT, 0263003246, 6590A5
• Other Numbers: 263003246, 9649614177

Compatibility Notes

This sensor is referenced by multiple OEM numbers and is typically used on Citroën models such as C4 Picasso and C5. Compatibility with a specific vehicle depends on the exact part number originally fitted. Use the listed product and other numbers to confirm a match with the vehicle’s existing sensor.

Replacement Procedure (Basic Guide)

Suitable for professional technicians and experienced DIYers. Typical replacement steps:

1. Park the vehicle on a level surface, engage the handbrake and, if possible, place the transmission in park or neutral with the engine off.
2. Disconnect the negative battery terminal before starting electrical work to avoid short circuits and electrical damage.
3. Access the sensor from the bumper: remove inner trim or wheel arch liner as required to reach the sensor connector and retaining clip.
4. Disconnect the electrical connector and carefully release the retaining clip or pull the sensor out of its mounting cup. Avoid excessive force to prevent damage to the bumper or connector.
5. Compare the new sensor with the old one to confirm identical connector type and mounting orientation, then fit the replacement into the bumper hole until it clicks into place.
6. Reconnect the electrical connector, reassemble the trim/wheel arch liner, reconnect the battery, and run a functional test of the PDC system (engage reverse gear or use the vehicle’s PDC test procedure).

Installation Recommendations

• Always ensure the replacement sensor matches the original OEM code and connector type before installation.
• Clean the bumper mounting area and check the wiring harness and connector for corrosion or damage prior to fitting the new sensor.
• When routing or refitting inner liners, avoid pinching the sensor wiring and ensure connectors are fully seated and locked.
• After installation, verify correct operation across the full detection range and check for stored fault codes with a diagnostic tool if an alert persists.

Why This Part Fails Most Often

• Physical Damage: Impact from low-speed collisions or curb strikes can crack the sensor face or dislodge internal components.
• Water Ingress and Corrosion: Moisture penetration or persistent exposure to road salt can corrode pins and connectors, causing intermittent or permanent failure.
• Contamination and Paint Overspray: Dirt build-up, heavy contamination, or overspray during bumper painting can degrade ultrasonic performance.
• Wiring and Connector Faults: Chafed wiring, poor connector contacts, or damaged harnesses frequently mimic sensor faults.
• Age and Wear: Over time, seals and housings wear, reducing reliability — longevity depends on operating environment and maintenance.

Post-Installation Check

After replacement, perform a system check: engage the PDC (usually by selecting reverse) and verify audible and visual alerts at varying distances. If the system shows faults, scan for diagnostic trouble codes and inspect connectors and wiring. In case of persistent errors after fitting a correctly coded sensor, inspect the PDC control module and wiring harness.

Are you looking for a reliable parking sensor for your Citroën or Peugeot? This high-quality used auto part ensures optimal performance of your parking assistance system. Suitable for models such as the Citroën C8 and Peugeot 807, this sensor is an ideal choice to restore full functionality of your parking aids.

Parking sensors are essential components in modern vehicles, helping prevent accidents by alerting drivers about obstacles in blind spots during parking maneuvers. Since this sensor has proven itself in real-world use, you can trust its reliability and long service life, which is crucial when considering a used replacement part.

Technical Information

Manufacturer: PSA (Peugeot Société Anonyme) for Citroën and Peugeot brands
Models: Citroën C8, Peugeot 807
Product Codes: 9649186580, 659095

This sensor is easy to integrate into your vehicle and is designed to withstand typical wear and tear common to daily-driven auto parts. Purchasing this part provides you with a functional and precise component while saving cost compared to a new replacement, without compromising on quality or reliability.

Equip your vehicle with a parking sensor that enhances safety and convenience when parking. This used part offers a combination of high quality and affordable pricing, all aimed at improving your driving safety and comfort.

PDC wiring is essential for the proper functioning of the park distance control system, helping you to park safely even in tight spaces. By directly replacing your original part with our quality used product, you regain functionality without the need to invest in more expensive new components.

Technical Information:
Manufacturer: PSA CITROEN PEUGEOT
Model: Peugeot 307
Product Codes: 9653217780, 6528T7
Other Numbers: This wiring may also be compatible with other Peugeot models based on matching product codes.

Our team of specialists in used auto parts focuses on detailed inspection and assessment of each component to guarantee its best condition and seamless functionality. Although the condition of the sensors is left unassessed, the wiring is intact, ensuring its smooth integration into your vehicle.

Shop with confidence for your vehicle parts from experts in used auto parts. This product for Peugeot 307 is a great choice for any DIY enthusiast or professional mechanic looking for quality and reliability at a reasonable price. Remember, the proper functioning of park sensors is crucial for your safety and convenience when parking.

Parking sensors typically fail due to exposure to harsh weather conditions, electrical failures, or physical damage from impacts. If your sensors are not functioning properly, it’s advisable to replace them to maintain optimum parking safety.

Replacing the parking sensor is straightforward; it usually involves disconnecting the old sensor from its wiring harness, removing it from the bumper, and installing the new one in reverse order. Ensure that you connect the new sensor securely for reliable operation.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C3, Citroën C4, Peugeot 207, Peugeot 307, Peugeot 807
• Product Codes: 9653849080, 9652965177, 9653211577
• Additional Numbers: 6590H1, 602782

Parking sensors play a crucial role in assisting drivers by detecting obstacles in proximity, thus preventing potential accidents during parking maneuvers. Regular wear and tear or electrical issues in the vehicle can lead to sensor failure, making timely replacement essential for optimal performance.

To change the parking sensor, simply disconnect the vehicle’s battery to ensure safety, remove the faulty sensor from its housing, and plug in the new one. Reconnect the battery and test the sensor functionality.

Technical Information:

• Manufacturer: Bosch
• Model: Applicable for Citroën and Peugeot vehicles.
• Product Codes: 0263003266, 9650935277J1, 659088
• Other Numbers: 263003266

Are you looking for a reliable parking sensor for your Citroën or Peugeot vehicle? This genuine original part from renowned manufacturer Bosch fits models such as the Citroën C5 X7, Peugeot 308, and Peugeot 407. It is the ideal choice for owners seeking dependable and accurate parking assistance.

Installation of this sensor is straightforward and quick, making it suitable for both professional auto mechanics and car repair enthusiasts. The sensor enhances parking safety by effectively detecting obstacles behind the vehicle, thereby minimizing the risk of accidents or vehicle damage. Thanks to its high sensitivity and precise distance indication, parking becomes a simple and secure operation.

Technical Information:

Manufacturer: Bosch
Model: Suitable for Citroën C5 X7, Peugeot 308, Peugeot 407
Product Codes: 9663821577XT, 0263003667
Additional Numbers: 6590F6

This parking sensor is an essential aid for anyone looking to improve their vehicle’s parking performance. It increases comfort and safety during tight city parking or crowded parking lots. Designed to ensure long-lasting reliability and accuracy, it is especially valuable for older but well-maintained vehicles.