High-quality replacement steering wheel control module manufactured by Valeo, designed specifically for Citroën C4 series vehicles. This control panel integrates multiple functions into one compact unit, allowing convenient operation of cruise control, audio system, trip computer and the horn directly from the steering wheel. Ideal for professional garages and experienced DIY mechanics searching by product codes 96624941ZD or 6242Y9.

Why Buy This Part

This original-design Valeo unit restores factory steering-wheel functionality and improves driver convenience and safety. Typical fitment and direct product codes make it easy to find and order the correct part. Suitable for workshops replacing worn or faulty switch clusters, or for owners restoring full steering control functions after damage or electrical faults.

Installation Recommendations

• Safety First: Remove the ignition key and disconnect the negative battery terminal before starting. Wait at least 10 minutes for residual charge to dissipate from the airbag system.
• Airbag Handling: Carefully remove the airbag module according to manufacturer procedure—do not pull on airbag connectors or wiring. Store the airbag with the cover facing up.
• Accessing the Switches: Remove steering wheel trim panels and any retaining screws. Note the position of the steering wheel and alignment marks before removing the wheel center nut (if wheel removal is required).
• Electrical Connections: Unplug the switch harness connectors and replace the switch unit. Ensure connectors are seated correctly and free of corrosion or debris.
• Reassembly: Refit trim, torque steering wheel fasteners to manufacturer specification, reconnect the battery and verify all functions (cruise control, radio controls, onboard computer, horn) operate correctly.
• Recommendation: If you are unfamiliar with airbag or steering wheel work, have the installation performed by a trained technician. Always follow Citroën service manual procedures to avoid injury or damage.

Most Common Failure Reasons

• Wear and Tear: Frequent use causes mechanical wear of button contacts and plastic components, leading to intermittent or non-responsive switches.
• Contamination: Dirt, moisture or spilled liquids can corrode contacts or cause short circuits in the switch assembly.
• Mechanical Damage: Impact or rough removal of the airbag/trim can break switch housings or connectors.
• Electrical Issues: Faulty wiring, poor connector contact or problems in related steering electronics can mimic a failed switch assembly.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C4, C4 Picasso, Grand C4 Picasso
• Product Codes: 96624941ZD, 6242Y9
• Other Numbers: NFP (as referenced in original listing)

Symptoms indicating replacement: Buttons not responding, functions working intermittently, cruise control not engaging via steering controls, radio or onboard computer controls non-functional, or horn not activating from steering wheel. When searching for the correct part online or in catalogs, use the OE codes 96624941ZD and 6242Y9 to increase match accuracy.

Perfect for professional mechanics and confident DIYers who need a direct-fit replacement steering wheel control unit for Citroën C4 models. Order now to restore full steering-wheel control functionality and improve in-car convenience.

High-quality Valeo steering column stalk assembly designed for Citroën C4 first generation and C4 Picasso/Grand Picasso models. This multifunction stalk unit operates fog lights, front and rear wipers, the rain/wiper sensor and the on-board computer functions. Ideal for professional workshops and skilled DIYers seeking a direct replacement using OEM-equivalent part numbers. Commonly searched by product codes, the listing increases findability for mechanics and car owners repairing electrical controls behind the steering wheel.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C4 I; Citroën C4 Picasso; Citroën C4 Grand Picasso
• Product Codes: 96644965XT, 6242HL, 624348
• Additional Numbers: NFP

Function

This multifunction stalk controls the vehicle’s fog lights, front and rear windscreen wipers, interfaces with the rain/wiper sensor and cycles information on the on-board computer. It replaces the left/right stalk assembly that houses the switches and electrical contacts used for these functions.

Compatibility

Designed for Citroën C4 (first generation) and both C4 Picasso and C4 Grand Picasso models that use the Valeo-style steering column stalk assembly. Always verify the part numbers listed in the Technical Information against the unit removed from the vehicle to ensure correct fitment.

Replacement Procedure

• Disconnect the battery before starting work to avoid short circuits and airbag deployment.
• Remove the steering wheel trim and airbag (follow manufacturer safety steps) if necessary to access the column shrouds.
• Unscrew and remove the upper and lower steering column covers to expose the stalk assembly.
• Disconnect electrical connectors from the stalk unit and remove any retaining screws or clips.
• Install the new stalk, secure fasteners, reconnect connectors and reassemble the column covers and steering wheel components.
• Reconnect the battery and verify all functions: fog lights, front/rear wipers, rain sensor input and on-board computer controls.

Installation Recommendations

• Inspect connector pins and harness for corrosion or damaged insulation; repair as required before installation.
• Use appropriate torque and follow airbag handling procedures when removing/reinstalling the steering wheel or airbag module.
• Test all functions with the ignition on and run through wiper cycles and fog light activation to confirm proper operation.
• If intermittent faults persist after replacement, check related fuses, grounds and wiring continuity with a multimeter.

Most Common Failure Causes

• Wear of internal contacts from frequent use leading to intermittent or non-functioning switches.
• Moisture ingress or corrosion affecting connectors and printed circuit traces inside the stalk.
• Mechanical damage to plastic levers or retaining clips during operation or removal.
• Faulty wiper sensor signals or connector problems that mimic stalk failures.

Notes for Mechanics and DIYers

This part is suitable for professional fitment or experienced DIY technicians familiar with steering column disassembly. Diagnostics should include checking fuses, connector condition and wiring continuity before replacing the stalk assembly to avoid unnecessary part changes. Searching by the listed product codes (96644965XT, 6242HL, 624348) will help locate the correct replacement quickly.

This replacement Valeo multifunction stalk is a direct-fit control unit designed for early Citroën C4 models and first-series C4 Picasso/Grand Picasso. It consolidates multiple functions into a single ergonomic module: front and rear wiper control (including intermittent and wash functions), fog light switching, rain/wiper sensor interface and certain onboard computer inputs. The compact design and OE-style connectors make it suitable for workshop fitment or competent DIY repairs. Common search terms include Citroën C4 stalk switch, Valeo steering column controls, and the listed part numbers — useful when technicians look up the part by code.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C4 (I), Citroën C4 Picasso (First Series), Citroën C4 Grand Picasso (First Series)
• Product Codes: 96644963XT, 6242HJ, 624346
• Additional Numbers: 6242.HJ

Compatibility And Fitment

Intended For First Generation Citroën C4 Platforms Including Standard C4, C4 Picasso And C4 Grand Picasso. Always Match The Part Codes Listed Above With The Unit On The Vehicle To Confirm Fitment. The Module Mounts On The Steering Column Behind The Upper And Lower Trim Covers And Connects Via The Original Multi-Pin Harness.

Installation Recommendations

• Disconnect The Battery And Wait Several Minutes Before Starting Work To Reduce The Risk Of Airbag Deployment And Electrical Damage.
• Remove Steering Column Trim Panels (Typically Secured By Screws) To Access The Stalk Module.
• Unplug The Electrical Connector Carefully, Release Any Retaining Clips And Remove The Old Stalk.
• Install The New Unit By Reversing The Removal Steps. Ensure Connectors Are Fully Seated And Clips Engaged.
• Check All Functions After Reinstallation: Front/Rear Wipers, Intermittent Settings, Washer, Fog Lights And Any Steering Wheel/On-Board Computer Inputs Associated With The Stalk.
• Allow A Trained Technician With The Correct Tools To Complete The Job If The Vehicle Requires Steering Angle Sensor Recalibration Or Additional Electrical Checks.
• Estimated Replacement Time For Experienced Technician: 30–60 Minutes.

Why The Part Typically Fails

Failure Is Most Often Caused By Mechanical Wear And Electrical Contact Degradation Over Time. Frequent Use Of Wiper And Light Functions Leads To Contact Pitting And Intermittent Connections. Moisture Ingress And Corrosion On Connectors Or Internal Switch Contacts Accelerate Failure, Especially In Older Vehicles Or Cars Exposed To Road Salt. Physical Damage To Plastic Levers Or Mounting Clips Is Also Common After Years Of Use.

Fault Symptoms

• Intermittent Or Nonfunctional Wipers (Front Or Rear).
• Washer Function Works But Wipers Do Not Respond Correctly.
• Fog Lights Fail To Switch On Or Off Via The Stalk.
• Erratic Intermittent Wiper Behavior Or Loss Of Intermittent Settings.
• Loose Or Broken Lever With Mechanical Play.

For workshops and DIYers looking up parts by code: use the product codes listed in the Technical Information section to locate the correct Valeo stalk for Citroën C4 I and associated Picasso variants. Proper diagnosis of electrical faults (metering connectors, continuity checks) can save time and avoid unnecessary replacement if the cause is wiring or a blown fuse rather than the stalk itself.

Original VALEO steering wheel controls for Citroën C4 – used, fully functional parts from the PSA concern. An ideal replacement for non-functioning buttons/lever for controlling the cruise control, car radio, on-board computer and horn. Designed primarily for mechanics and home repairers looking for OE number compatibility assurance.

Key features
– Functions: cruise control/speed limiter, radio and on-board PC control, horn
– Manufacturer: VALEO (original PSA supplier)
– Condition: used original part (no cheap replacement)
– Mounting position: under the steering wheel – left and right module (satellites)
– Color/design: black, surface with button pictograms

OE/OEM numbers to search and check compliance
– 96624936ZD (VALEO/PSA)
– 6242.N4 (6242N4) – cruise control controller
– 6239.RZ (6239RZ) – radio/board PC controller
Note: Always compare your original number and shape of connectors/mounts before ordering.

Compatibility
– Citroën C4 I (approx. 2004–2010)
– Citroën C4 Picasso and C4 Grand Picasso I (approx. 2006–2013)
Suitable for most engines and equipment, where the equipment in question is from the factory or prepared in BSI. Cruise control may require activation in the control unit (Diagbox/Lexia).

Technical information and assembly
– Connection: multi-pole connectors to the unit under the steering wheel
– Installation: requires removal of the steering wheel/airbag. Before working, disconnect the battery and wait min. 10-15 minutes due to airbags.
– Typical symptoms of a defect in the original parts: non-functioning scroll/buttons, cruise control outages, random switching of functions
– After replacement, it is recommended to test all functions and, if necessary, perform basic settings/activation

Why choose this part?
– Original VALEO – exact fit, correct button logic and reliability
– Quick restoration of full cruise control functionality and radio control without additional wiring adjustments
– Broad compatibility within the first generation C4/C4 Picasso models

What you will receive
– Controls under the steering wheel for Citroën C4/C4 Picasso matching OE: 96624936ZD, 6242.N4, 6239.RZ
Note: Please refer to the part numbers and connector appearance on the photos of your car.

Searching by part number? Enter in the search: 96624936ZD, 6242.N4, 6239.RZ, “Citroën C4 steering wheel controls”, “C4 cruise control control”, “C4 Picasso radio control”. This will increase the chance of finding the right piece quickly.

The Steering Wheel Radio Control by Citroën and Peugeot is a crucial component for enhancing driving comfort and safety. This used part, product code 4112FA, comes from the Citroën Xsara Picasso 2001 model and fits several models from these brands. By enabling multimedia system control directly from the steering wheel, this part increases driving safety by minimizing the need to divert attention from the road.

Technical Information:

Manufacturer: PSA (Peugeot Citroën)
Model: Primarily Citroën Xsara Picasso, compatible with other Citroën and Peugeot models
Product Codes: 4112FA
Other Numbers: NFP

This steering wheel control unit is essential for drivers who prefer smooth operation of their vehicle’s functions without distracting movements. It is common for original controls to fail over time due to internal wear and frequent use. Replacing this part ensures the restoration of original functionality and vehicle comfort.

We recommend installation by a qualified auto mechanic to guarantee proper fitting and full functionality of the component. With correct installation and compatibility, this part is not only a replacement but an improvement for your vehicle.

Buy with confidence from our range of quality used parts and ensure your Citroën or Peugeot remains fully functional and safe for all your journeys.

This integrated steering wheel switch module restores full control of cruise control, audio functions, on-board computer menus and the horn. Designed as a direct-fit replacement for compatible Citroën C4 models, the unit is ideal for professional workshops and experienced DIY mechanics who need a reliable OE-quality control interface. Commonly searched by part numbers, the module simplifies troubleshooting and replacement when steering wheel switches become intermittent or unresponsive.

Technical Information

• Manufacturer: Valeo
• Model: Citroën C4; Citroën C4 Picasso; Citroën C4 Grand Picasso
• Product Codes: 96624938XT; 6242P0
• Additional Numbers: 98003833ZD; 98003833D

How The Part Is Replaced

Replacement involves safe removal of the steering wheel airbag and access to the switch module on the steering wheel hub. Typical steps:

• Disconnect the negative battery terminal and wait at least 10 minutes to allow SRS capacitors to discharge.
• Remove the airbag module following the manufacturer’s procedure and carefully disconnect airbag connectors.
• Mark steering wheel alignment relative to the column to ensure correct reinstallation.
• Remove the steering wheel retaining bolt and withdraw the steering wheel to access the switch module and connectors.
• Disconnect electrical connectors, replace the switch module, reconnect connectors and reassemble in reverse order.
• After reconnection, verify all functions (cruise control, audio controls, on-board computer navigation and horn) before normal use.

Installation Recommendations

• Always follow Citroën factory procedures when removing the airbag and steering wheel. If unsure, have the work performed by a qualified technician.
• Disconnect the battery and wait at least 10 minutes before touching any SRS components to reduce the risk of accidental deployment.
• Mark steering wheel position to maintain correct alignment and avoid steering angle sensor issues.
• Inspect wiring harnesses and connector pins for corrosion or damage and clean contacts before reassembly.
• Test all steering wheel functions on a safe test drive after installation.

Why The Part Fails Most Often

• Mechanical Wear: Frequent use of buttons and rocker switches gradually wears contact surfaces and plastic components.
• Wear On Flex Cable Or Connectors: Repeated steering movement can stress ribbon cables and connector contacts, causing intermittent faults.
• Moisture And Corrosion: Exposure to moisture or contaminated hands can lead to corrosion of electrical contacts.
• Impact Or Physical Damage: Accidental impacts or improper removal of the steering wheel/airbag can damage the module.
• Age Related Electrical Faults: Deterioration of solder joints or internal components over many years in service.

Customers frequently search for this part using product codes such as 96624938XT, 6242P0 and 98003833ZD. The unit is supplied used but with a guarantee of functionality and may show signs of prior use.

Are you looking for a reliable replacement for your steering wheel controls for your Citroën? We offer used, fully functional steering wheel controls for Citroën C4 models, including C4 Picasso and Grand Picasso versions. These controls serve to operate the cruise control, radio, onboard computer, and horn, ensuring a more comfortable and safer driving experience.

The controls have been carefully inspected and are ready for immediate installation. Exact compatibility with Citroën models ensures easy mounting without the need for further modifications. This part is ideal for mechanics and DIY enthusiasts looking for a quality yet affordable solution for vehicle repair or maintenance.

Technical Information:
Manufacturer: Valeo
Model: Citroën C4, C4 Picasso, C4 Grand Picasso
Product Codes: 96624940ZD, 6242Y8
Other Numbers: N/A

With its robust design and compatibility, this part is suitable for frequent use and long-term operation of the system. If you need to restore the functionality of the steering wheel controls in your vehicle, this product represents a reliable and cost-effective choice.

High-quality Valeo steering wheel control assembly designed for Citroën C4 family cars. This multifunction unit integrates switches for cruise control, audio functions and the horn, enabling safe and ergonomic operation without taking hands off the wheel. The part is commonly searched by product codes 96624935ZD, 6239QZ and 6242EZ, so entering these references in catalogs or search engines will quickly locate the exact item.

Designed with professional fitment in mind, this control module is suitable for workshop replacement and for experienced DIY mechanics. The compact design keeps wiring and connectors consolidated behind the steering wheel, reducing the risk of loose contacts and improving reliability compared with individual aftermarket modifications. Ideal when original switches are worn, sticky or unresponsive.

Technical Information

• Manufacturer: Valeo (for Stellantis / Citroën / Peugeot)
• Model: Citroën C4, C4 Picasso, Grand Picasso
• Product Codes: 96624935ZD, 6239QZ, 6242EZ
• Other Numbers: NFP (as noted in supplier listing)

Installation Recommendations

1. Disconnect the vehicle battery before starting work to avoid short circuits and accidental airbag deployment.
2. Follow the vehicle manufacturer’s procedure for airbag and steering wheel removal. Remove the airbag module and steering wheel to access the control assembly.
3. Unplug all electrical connectors and carefully remove the old switch assembly. Inspect the wiring harness and clock spring for damage while components are exposed.
4. Fit the new Valeo unit, reconnect connectors and reassemble in reverse order. Ensure connectors are fully seated and locking tabs engage.
5. After reassembly, reconnect the battery and test all functions: cruise control activation, audio controls, horn and steering wheel switches. Check for any warning lights related to airbag or steering electronics.
6. If any steering electronics or airbag warnings appear after fitment, consult diagnostic equipment and follow the manufacturer’s fault codes and clearing procedures.

Most Common Failure Reasons

• Wear and Tear: Frequent use of buttons causes mechanical wear and loss of tactile response over time.
• Electrical Contact Degradation: Oxidation or contamination on switch contacts can make buttons intermittent or non-functional.
• Connector Or Wiring Damage: Strain, corrosion or chafing on the wiring harness or connector pins can interrupt signals to the steering controls.
• Ingress Of Moisture Or Debris: Water or dirt entering the assembly (often via steering column seals) can short or corrode internal parts.
• Associated Component Faults: Problems with the clock spring or related steering column electronics can mimic switch failure; inspect related parts during replacement.

For professional results, perform the replacement in a workshop environment with appropriate tools and safety measures. Using the correct product codes when ordering helps ensure you receive the precise Valeo steering wheel control compatible with Citroën C4, C4 Picasso and Grand Picasso models.

Are you searching for reliable replacement parts for your Citroën vehicle? We offer tested steering wheel controls previously used in Citroën C4, C4 Picasso, and C4 Grand Picasso models. These controls enable convenient management of cruise control, car radio, and horn directly from the steering wheel, contributing to safer and more comfortable driving.

This original part from the manufacturer Valeo is specially designed for Citroën vehicles, ensuring high compatibility and reliability. Installation is straightforward and requires no modifications, making it easy for professional auto mechanics and experienced DIYers alike. Functional and condition checks are fundamental before reuse, enhancing the longevity and sustainability of your vehicle.

Technical Information:

Manufacturer: Valeo
Model: Citroën C4, C4 Picasso, C4 Grand Picasso
Product Codes: 96497900XT, 6239QZ, 6242EZ
Additional Numbers: Specific product numbers are provided to verify and locate the correct part for your vehicle model.

Steering wheel controls are generally considered low-wear components, but regular functionality checks are recommended. Using original parts guarantees the best possible performance and reliability. Whether you maintain your vehicle professionally or as a DIY project, relying on quality and verified components is crucial.

Investing in original steering wheel controls means investing in your safety and driving comfort. Manufactured from high-quality materials with proven design, this part is the ideal choice for repair or upgrade of your Citroën vehicle.

Upgrade Or Replace Your Steering Wheel Control Cluster With This Genuine Valeo Unit Designed For Early Citroën C4 Models. The Module Consolidates Buttons For Cruise Control, Audio Commands And The Horn Into A Single Compact Assembly, Restoring Full Steering-Column Functionality For Workshop Repairs Or DIY Maintenance. Ideal For Automechanics And Experienced Do-It-Yourselfers, The Unit Is Often Searched By Its Product Codes And Fits Common Citroën C4 Variants.

Applications

Compatible With Citroën C4 I, C4 Picasso And Grand C4 Picasso Models Where Factory Steering-Wheel Controls Are Fitted. Verify Fitment By Matching The Physical Connector And Button Layout To Your Original Unit.

Technical Information

• Manufacturer: Valeo
• Model: Steering Wheel Controls For Citroën C4 / C4 Picasso / Grand C4 Picasso
• Product Codes: 96624935XT, 6239QZ, 6242EZ
• Additional Numbers: 6239QZ, 6242EZ, 96624935XT

Function And Benefits

This module Provides Direct Control Of Cruise Control Functions, Radio/Media Commands (Volume, Track, Mode) And The Horn Button From The Steering Wheel. Replacing A Faulty Switch Cluster Restores User Safety And Convenience, Eliminates Intermittent Electrical Contacts, And Prevents Unintended Cruise Or Audio Behavior Caused By Worn Buttons Or Broken Internal Contacts.

How To Replace On The Vehicle

Replacement Requires Caution Because Of The Airbag System And Steering-Angle Sensors. Typical Procedure:

• Disconnect The Battery And Wait At Least 10–15 Minutes To Ensure Airbag Capacitors Discharge.
• Remove The Steering-Wheel Airbag Module Following Manufacturer Procedures (Do Not Pry On The Airbag Cover).
• Disconnect Airbag Connectors And Any Retention Clips, Then Remove The Airbag Safely.
• Unscrew The Central Steering-Wheel Retaining Bolt And Note The Steering Wheel Alignment Mark To Preserve Wheel Position.
• Carefully Remove The Steering Wheel To Access The Switch Cluster And Connectors.
• Disconnect The Wiring Harness To The Steering Controls And Remove Any Retaining Screws Or Clips.
• Fit The Replacement Unit, Reconnect All Plugs, Reassemble Steering Wheel And Airbag, Then Reconnect The Battery.
• After Reassembly, Check All Functions (Horn, Radio Controls, Cruise Control) And If Required, Calibrate The Steering Angle Sensor Using Appropriate Diagnostic Equipment.

Installation Recommendations

• Always Disconnect The Battery Before Starting Work And Follow Manufacturer Safety Procedures For Airbag Handling.
• Inspect The Clock Spring (Spiral Cable) For Damage When Accessing Steering-Wheel Wiring; Replace If Showing Wear Or Intermittent Contact.
• Use The Correct Torques For Steering-Wheel Fasteners And Observe Alignment Marks To Avoid Steering-Angle Sensor Errors.
• Test All Functions Before Road Use; If Airbag Or Electronic Warnings Appear, Perform Diagnostic Clearing And Calibration With Proper PSA Service Tools.
• Recommended For Installation By Qualified Personnel Or Experienced DIYers Comfortable With Airbag And Steering-Column Work.

Why The Part Most Commonly Fails

Failures Usually Result From Mechanical Wear Of The Buttons, Dirt Or Moisture Ingress Causing Corrosion On Contact Surfaces, Or Broken Flex Ribbon/Clock-Spring Connections Caused By Steering Wheel Movement And Age. Heavy Use Of Cruise Or Audio Controls Accelerates Wear. Electrical Faults May Present As Intermittent Operation, Stuck Buttons Or Complete Loss Of A Function.