Drivers under the steering wheel Delphi COM2000 for Citroën/Peugeot – original used part with codes 96451821ZL and 6242G5. It is a complete module under the steering wheel (switch below the steering wheel), which ensures everyday control of lights and wipers. The ideal replacement for a fault of the direction lights, wipers or horn, when it is often found according to code 6242G5 / 96451821ZL.

Module function: control of dipped/long -distance and fog lights, rudders, front and rear wiper and washer, horn and on -board computer. It also supports automatic wiper modes (in rain sensor cars).

Compatibility according to models: Peugeot 206, 307 I, 406, 807 and Citroën C5 I, C8, Berlingo II, Partner II, Xsara and Xsara Picasso. Always verify the match by the part number and connectors to your original unit, because the dog used multiple variants of COM2000 according to the equipment.

Typical manifestations of defects and reasons of exchange: spontaneous flashing or ripples, non -functional horn, irregular wiper operation, non -return lever to the basic position or occasional loss of contact. The cause is mechanical wear of internal contacts and microswitches due to age and frequent use.

Installation notes: The replacement takes place under the steering wheel. Always disconnect the battery for safety reasons and wait a few minutes before dismantling the airbag. After removing the steering wheel, the COM2000 is released from the shaft and disconnects the connectors. During the installation, pay attention to the correct centenance and locking of the unit. In most cases, the plug & play; For some cars, the basic settings/configuration of functions via the diameter/lexia may be required after assembly (eg the presence of fog lights or rear wiper is controlled by BSI configuration).

technical information

• Manufacturer: Delphi (PSA Citroën/Peugeot)
• model: COM2000 – module lever under the steering wheel
• Product codes: 96451821zl, 6242G5
• Other numbers: 96 451 821 ZL, 6242.G5, COM2000

Tip for the correct selection: Compare the label on your original episode (numbers 9645… / 6242…) and the shape / number of connectors. Code agreement significantly increases the certainty of compatibility within the vehicle equipment.

COM2000 levers drivers for Citroën and Peugeot with multiplex wiring. The module under the steering wheel brings together control of lights, fog lights, rudders, front wipers and horn; The equipment also supports cruise control and remote control of the car radio (the radio driver must be delivered or transferred from the original episode as needed). Thanks to the original design of the dog is ensured proper communication with the on -board network and the functionality of all relevant systems.

This combined switch is located on the steering wheel pillar. Typical manifestations of its wear are spontaneous flashing, ripples outages, non -functional wiper interruptions, occasional clampson malfunction or problem control of fog lights. The replacement is suitable for the symptoms mentioned or after mechanical damage to the levers.

Mounting tip: disconnect the battery before starting work and wait for the system discharge (due to the airbag). Then remove the steering columns, remove the airbag steering wheel according to the manufacturer’s procedures and release the switch from the lock. Carefully compare the connectors, equipment (fog lights, cruise control, radio control) and unit designation before assembling the new part. For some cars, it is necessary to re -install a separate car radio driver or cruise control lever from the original part.

technical information

• Manufacturer: PSA (Citroën/Peugeot), designation of the COM2000 module
• Model: Peugeot 206; Peugeot 307 I; Citroën Berlingo II; Peugeot Partner II
• Product codes: 96605695XT (OE)
• Other numbers: COM2000, crowd

Recommendations for selection: follow the code 96605695XT and compare physical design and equipment. The right choice of variant ensures trouble -free functioning of rudder, lights, wipers and additional functions such as cruise control and audio system control.

Original combined switch below the Delphi COM2000 steering wheel for Citroën and Peugeot. Suitable as a replacement for defective rudder, lights and wipers on models with multiplex wiring. This module (dog codes 96511179XT, 6242C2) is often sought by part number and replaces the unavailable original (NFP). Ideal for Citroën C5 I, C8, Berlingo II and Peugeot 206, 307, 807, Partner II – Always compare numbers and connectors before ordering.

The function and equipment of the module vary according to the version of the car: usually includes fog lights, wipers (including rain sensor, if equipped with) the rear wiper, on-board computer, cruise control and car radio control. For the radio controller, it may be necessary to add or transfer the existing control from your car. If you are dealing with spontaneous switching of lights/wiper, impaired blinker return or non -functional switching of on -board computer modes, the replacement of the COM2000 module is a common and effective solution.

Installation notes: The replacement is removed by removing the steering wheel and plastic steering column covers. Always disconnect the battery for safety reasons and wait at least 10 minutes before handling the airbag. Then disconnect the module connectors, release the lock and replace the piece with a piece. In most cases, the installation of plug & play; Activation of cruise control (if the car did not have before) may require diagnostics and permission to function in BSI/ECU. Compare the position and type of connectors, the lever and the equipment (fog lights, rain sensor, radio control).

technical information

• Manufacturer: Delphi (COM2000)
• Model: Citroën C5 I, C8, Berlingo II; Peugeot 206, 307, 807, Partner II
• Product codes: 96511179XT, 6242C2
• Other numbers: 624231, 9239p3

This is the original part of the removal. Before purchasing, please carefully verify the match by the number of the part and equipment of the car; Different variants of COM2000 differ according to functions (fog lights, rain sensor, cruise control, radio control). Thanks to accurate pairing according to OEM codes (96511179XT, 6242C2, 624231, 9239p3), you minimize the risk of incompatibility and get a reliable replacement for the original module, which is already kept as NFP.

Looking for reliable spare parts for your Peugeot 307? Our drivers under the steering wheel marked with codes 96605602XT and 6242A7 are the ideal choice to maintain your car. These parts were carefully selected and tested to match original specifications and ensure smooth performance.

The levers drivers are key to the smooth control of your vehicle and ensure control of many features such as lights, fog lights, cruise control and car radio. In addition, through the integration with the on -board computer and the wiper sensor, they allow both the front and rear wiper to be effective. Choosing parts for the Peugeot 307, which work well and are reliable, is essential for your safety and driving comfort.

Technical Information:
Manufacturer: PSA Citroen Peugeot
Model: Peugeot 307
product codes: 96605602XT, 6242A7, 6242A6
More Numbers: NFP

These levers drivers are designed for the Peugeot 307, which guarantees their compatibility and high efficiency. Replacement of the old part for this quality product used can significantly improve the functionality of control in your vehicle. Our drivers under the steering wheel are not only practical, but also very reliable thanks to their robust performance and testing before sale.

Do not hesitate to increase the comfort of your Peugeot 307 with our quality levers. If you need any further information or have specific installation or functionality queries, we are available to you. Ensure these indispensable parts and enjoy a smooth ride with full control over the key features of your vehicle.

This cruise control stalk is a direct-fit steering column switch designed for Citroën and Peugeot models equipped with the combined COM2000/COM2002 control cluster. Built with professional workshops and DIY mechanics in mind, the part carries common OEM reference numbers used in service and spare-part searches, making it easy to find and replace. The stalk restores reliable speed-hold and resume functions, improving driver comfort on longer journeys and ensuring correct interaction with the vehicle’s cruise system.

Features And Application

• Direct Fit For Vehicles Using COM2000 / COM2002 Instrument Cluster.
• Compatible With Numerous Citroën And Peugeot Models — Typical Applications Include 206, 307, 406, 407, 807, Berlingo II, C5 I, C8, And Partner II.
• OEM Cross-Reference Numbers Included To Simplify Searching And Ordering.
• Designed For Mechanics And Skilled DIY Installers — Simple Mechanical Replacement With Standard Tools.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën 206; Citroën 307; Citroën 406; Citroën 407; Citroën 807; Citroën Berlingo II; Citroën C5 I; Citroën C8; Peugeot 206; Peugeot 307; Peugeot 807; Peugeot Partner II
• Product Codes: 96336889XT, 9641796480, 96538213XT
• Additional Numbers: 96336889ZL, 6242Z9, 9633689XT

Installation Recommendations

• Always Disconnect The Battery Before Starting Work And Wait The Manufacturer-Recommended Time To Deactivate The Airbag System.
• Remove Steering Column Trim Carefully To Access The Stalk Mounting Screws Or Clips.
• Unplug Electrical Connector(s) From The Old Stalk; Note Connector Positioning To Avoid Incorrect Reassembly.
• Fit The Replacement Stalk In Reverse Order, Ensuring Secure Fastening Of Screws And Proper Routing Of Wiring Harnesses.
• After Installation, Verify All Cruise Functions (Set, Resume, Cancel) And Check The Instrument Cluster For Fault Codes; Clear Any Stored Faults If Present.

Common Failure Reasons

• Mechanical Wear And Tear Of The Internal Switch Contacts After Years Of Use.
• Oxidation Or Corrosion Of Electrical Contacts, Especially In Vehicles Exposed To Moisture.
• Physical Damage From Impact Or Improper Handling During Steering Repairs Or Airbag Deployment.
• Intermittent Operation Caused By Loose Connectors Or Damaged Wiring In The Steering Column.
• Faults In The Combined COM2000/COM2002 Unit May Also Affect Cruise Function, So Diagnose Both The Stalk And The Control Unit.

Practical Tips

• When Replacing The Stalk, Inspect The Wiring Harness And Column Connectors For Corrosion Or Heat Damage — Repair Faulty Contacts Before Reassembly.
• Keep A Note Of The Original Part Number Before Removal To Ensure Correct Cross-Reference And Fast Reordering.
• Use Proper Torques On Fasteners And Avoid Over-Bending The Stalk To Prevent Premature Failure.

Why Mechanics Choose This Part

Clear OEM References, Direct Fitment To Common Citroën And Peugeot Models, And A Robust Mechanical Design Make This Cruise Control Stalk A Reliable replacement option for workshops and experienced DIYers. The part simplifies repairs, reduces vehicle downtime, and restores full cruise functionality without major electrical work in most cases.

Looking to restore the control panel functionality of your Citroën or Peugeot vehicle? These steering column switches are a critical component for comfort and safety, ensuring smooth management of multiple vehicle systems from one convenient location. Designed specifically for seamless integration, they offer an efficient and cost-effective solution for mechanics and DIY car enthusiasts alike.

Compatible with a range of models including Citroën 206, 307, 406, 807, Berlingo II, C5 I, C8, Partner II and various Peugeot vehicles, installation is straightforward. The switches fit directly into the existing electronic system, restoring full operation of your vehicle’s functions and helping you get back safely on the road.

Technical Information

• Manufacturer: Delphi
• Model: COM 2000
• Product Codes: 96595091XT, 6242C6, 6239Y5, 6239M6, 6239QA, 6239T6, 6239W5, 6239X5, 6239Y9, 624220, 6239P0, 6239Y0
• Additional Numbers: As listed in product description

This steering column switch is a perfect replacement part often required due to mechanical wear and aging material fatigue after extensive use. Its tailored fit ensures smooth compatibility with your Citroën or Peugeot vehicle’s electronic system. Renewing your vehicle’s control interface with this component enhances both driving comfort and vehicle safety.

Looking for high-quality and reliable steering column switches for your Citroën or Peugeot? Our used auto parts are an excellent choice for professional mechanics or individuals who prefer to perform vehicle repairs themselves. These switches are essential for the proper functioning of many key vehicle components.

This product enables full control over lights, fog lamps, front and rear wipers, indicators, horn, electronic stability program (ESP), cruise control, and the car stereo — particularly useful if you wish to maintain your current control setup or transfer switches from an original configuration.

Technical Information:

• Manufacturer: PSA Citroën Peugeot
• Model: Primarily compatible with Peugeot 307
• Product Codes: 96439234ZL, 6242F3
• Additional Numbers: NFP

Our steering column switches are designed to meet the original equipment specifications and ensure seamless integration and operation. Since these are older parts, we recommend thoroughly verifying product compatibility with your specific vehicle.

Purchase from us to obtain reliable auto parts with a solid performance history and long service life. Our products are carefully inspected to guarantee their functionality, helping keep your vehicle safe and fully operational.

Designed for direct replacement, this product simplifies the installation process. It is crucial to close attention to signs of wear and tear, as the switch can fail over time due to intense usage or exposure to moisture. Regularly inspecting and replacing the switch when malfunctioning can prevent further electrical issues in your vehicle.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: 206, 307
• Product Codes: 96593490XT, 96605589XT, 624296
• Additional Numbers: 624296, 96593490XT, 96605589XT

This transponder antenna is a direct-fit component designed for Peugeot and Citroën models that use a conventional (non-multiplex) immobilizer system. Ideal for professional workshops and competent DIYers, the unit reads the key transponder signal around the ignition switch and relays it to the immobilizer control module. Replacement of a faulty antenna restores reliable key recognition and eliminates no-start conditions caused by missing transponder communication.

Compact and discreet, the antenna assembly typically mounts around the ignition barrel or column. It is commonly sought by part number (9632487880 / 616069), making it easy to find in catalogs or when ordering spare parts. Technically simple but crucial for vehicle security, this antenna ensures the transponder coil can communicate with the vehicle ECU to permit engine start.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: 206, 307 I, 406, Berlingo I, Berlingo II, Expert II, Jumpy II, Partner I, Partner II, Xsara, Xsara Picasso
• Product Codes: 9632487880, 616069
• Other Numbers: NFP

Installation Recommendations

Before starting work, disconnect the battery and wait a few minutes to avoid accidental short circuits. Typical replacement steps:

• Remove the lower steering column trim and any covers around the ignition switch.
• Unplug the antenna connector and detach any retaining clips.
• Replace the antenna with the new unit, ensuring the coil sits concentrically around the ignition barrel.
• Reconnect the connector, reassemble trims and reconnect the battery.

Always follow the vehicle manufacturer’s removal and installation procedure to avoid damage to the ignition barrel, wiring harness, or surrounding components.

Why The Part Most Commonly Fails

Failures are usually caused by mechanical damage to the antenna or connector (from collisions or rough handling during steering column work), corrosion or moisture ingress, broken or fatigued wiring, or degraded solder joints in the coil. Symptoms include intermittent or complete loss of key recognition, immobilizer warning lights, and engine cranking without start.

Practical Notes For Mechanics And DIYers

When replacing the antenna, inspect the connector pins and wiring for corrosion or damage and test continuity where possible. If the immobilizer fault persists after antenna replacement, check the immobilizer control module and key transponder battery/state. Because this part is specific to non-multiplex systems, confirm that the vehicle does not use a multiplexed CAN/BSI configuration before ordering.

Part number 9632162780 4112AG is compatible with models including the Peugeot 206, 307 I, 406, Berlingo I, Berlingo II, Expert II, Jumpy II, Partner I, Partner II, Xsara, and Xsara Picasso.

Replacement of the rotary contact is typically needed when the airbag warning light remains illuminated or when there are issues with airbag deployment, which can occur due to wear and tear over time. Regular inspection and timely replacement of this component can prevent safety risks associated with malfunctioning airbags.

Technical Information

• Manufacturer: PSA
• Model: Citroën Peugeot
• Product Codes: 9632162780
• Additional Numbers: 4112AG