Multifunctional controls under the steering wheel (COM 2008) for Peugeot 3008 I and 5008 I ensure comfortable and safe control of the car’s key functions – direction and dipped beam lights, front fog lights, cruise control/speed limiter, control of the car radio, front wipers including rain sensor and communication with ESP. It is a central module with levers and integrated electronics that is directly connected to the vehicle’s network and shares data with, for example, the stabilization system.

This particular type corresponds to the part numbers below and is for the first generation 3008 and 5008 models. PSA offered multiple variants of the COM2008 depending on trim (with/without cruise control, with/without rain sensor, etc.), so matching the codes on your original part label and connectors is essential. If you have the numbers listed, this is the correct replacement.

When to change the part: typical symptoms of a defect are spontaneous switching or failure of turn signals or wipers, non-functioning cruise control, problems with the radio control on the lever, an ESP/ASR error message related to the angle of the steering wheel, or intermittent contacts in some positions of the lever. Due to the age of the cars and the mechanical wear of the switch contacts, the replacement of the COM2008 is quite frequent in these models.

Installation in a nutshell: disconnect the battery before work and wait a few minutes for the airbag. Remove the steering wheel airbag, release and retract the steering wheel, remove the plastic shaft covers and release the COM2008 module fuses. After the replacement, we recommend initializing/telecoding the variants via diagnostics (Diagbox/Lexia) and calibrating the steering wheel angle sensor so that the ESP, cruise control and wipers with rain sensor work correctly.

Compatibility: the module is designed for Peugeot 3008 I and 5008 I cars (approx. 2009-2016) with the corresponding equipment according to the codes below. The same platform and COM2008 designation are used for other Peugeot and Citroën models; however, always follow the matching part number and connector design.

Technical information

• Manufacturer: PSA Peugeot Citroën
• Model: Peugeot 3008 I (T84), Peugeot 5008 I (T87)
• Product codes: 96663613XT, 96773912ZD, 6243WP
• Other numbers: 6243.WP, 6243 WP, COM 2008, COM2008, 96663613 XT, 96773912 ZD

Before ordering, please compare the numbers and equipment of your car (cruise control, rain sensor, type of connectors). Correct matching will guarantee full functionality of lights, wipers, cruise control, radio control and communication with ESP.

Product Overview

High-quality steering column stalk switches (COM2008) designed for Citroën/Peugeot vehicles. This unit consolidates multiple controls on a single stalk assembly: lighting, fog lamps, cruise control, audio commands and front wiper functions including rain sensor signalling to the vehicle. Commonly searched by part numbers 96667319XT, 96773912ZD and 624399, this switch assembly is aimed at professional technicians and skilled DIYers who maintain Peugeot 3008 I and 5008 I models.

Features And Functions

• Integrated Control Of Headlights And Parking Lights
• Fog Light On/Off Functions
• Cruise Control Activation And Adjustment
• Radio/Audio Steering Commands (Where Fitted)
• Front Wiper Control Including Intermittent Settings
• Rain Sensor Interfacing (Signal To Vehicle System)
• ESP Signal Integration For Stability System Feedback

Compatibility

Designed For: Peugeot 3008 I, Peugeot 5008 I. Often Identified By: COM2008, 96667319XT, 96773912ZD, 624399. Always check the part numbers listed on the old unit before ordering to ensure exact match with your vehicle’s fitted assembly.

Replacement Procedure

Intended For Experienced Mechanics And Competent DIYers. Typical Replacement Steps:

• Disconnect The Vehicle Battery Before Any Work On Steering Column Electronics.
• Remove Steering Wheel Trim And Airbag Module Following Manufacturer Safety Procedures.
• Unscrew Or Unclip Steering Column Covers To Access The Stalk Assembly.
• Disconnect Multi-Pin Electrical Connectors And Release Retaining Clips Or Screws.
• Withdraw Old Stalk Assembly And Fit The Replacement, Ensuring Correct Connector Orientation.
• Reassemble Covers And Airbag, Reconnect Battery And Perform Functional Check Of All Controls (Lights, Wipers, Cruise, Audio).

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Peugeot 3008 I, Peugeot 5008 I
• Product Codes: 96667319XT, 96773912ZD, 624399, COM2008
• Other Numbers: T84, T87

Installation Recommendations

• Always Isolate The Battery Prior To Disassembly To Avoid Airbag Deployment And Electrical Damage.
• Follow Manufacturer Torque Specifications For Any Fasteners Around The Steering Column.
• Handle Airbag Modules And Connectors Carefully; Ensure Connectors Are Fully Engaged And Security Clips Are Replaced.
• After Installation, Verify All Functions: Dipped/Main Beam, Indicators, Fog Lights, Wipers (All Speeds), Rain Sensor Response, Cruise Control And Audio Commands.
• If Any Functions Are Missing After Fitment, Inspect Connector Pins For Damage Or Corrosion And Confirm The Correct Part Code Was Fitted.

Most Common Failure Reasons

• Wear Of Internal Contact Tracks From High Use (Indicators, Wipers, Cruise).
• Oxidation Or Corrosion Of Electrical Contacts Leading To Intermittent Operation.
• Mechanical Damage To The Stalk Lever From Impact Or Excessive Force.
• Ingress Of Moisture Or Dirt Causing Short Circuits Or Sticking Switches.
• Faulty Connectors Or Broken Retaining Clips Causing Poor Electrical Connection.

Notes For Purchase

Part Numbers 96667319XT, 96773912ZD and 624399 Are Frequently Used Search Terms; Include These In Your Order To Ensure Correct Item. Suitable For Workshops And Skilled DIY Enthusiasts Who Are Comfortable Working With Steering Column Electronics.

Order Now To Replace Faulty Stalk Controls And Restore Full Functionality To Your Peugeot 3008 I Or 5008 I Steering Column.

The Shift Paddle Controls are compatible with models such as the Citroën 3008 I, 407, and 5008 I, ensuring a perfect fit for your vehicle. Designed for durability, these controls often need replacement due to wear and tear from regular usage, making it crucial for maintaining optimal performance.

Replacing the Shift Paddle Controls is straightforward and can be done with basic tools. Typically, you would need to remove the steering wheel cover, disconnect the old controls, and install the new ones in reverse order. This replacement should be performed when you notice decreased responsiveness in the paddles or if any physical damage is observed.

Technical Information

• Manufacturer: PSA
• Model: Citroën, Peugeot
• Product Codes: 96667245XT, 98302853ZD, 624363
• Additional Numbers: 624363

Compatible with various Citroën and Peugeot models, including but not limited to 3008 I, 407, and 5008 I, these paddle controllers are an essential upgrade for both professional mechanics and DIY car enthusiasts. They help replace worn-out or malfunctioning components that can affect driving performance.

Regular maintenance and timely replacement of these parts can prevent issues such as unresponsive gear shifts or difficulty in controlling the vehicle, ensuring optimal performance over time.

Technical Information

• Manufacturer: PSA
• Model: Citroën, Peugeot
• Product Codes: 9666724577, 6243E4, 624363, 6242WK
• Additional Numbers: 62430000