This replacement dashboard speaker is intended for first‑generation Citroën C1 and Peugeot 107 vehicles (production up to 2013). It provides clear midrange reproduction for factory radio systems and is a common direct-fit spare part for vehicles with original equipment audio. Ideal for professional workshops and DIY mechanics looking to restore sound clarity in the instrument panel area.

Benefits and Use

Restores speech and midrange detail in factory audio systems, reduces distortion and rattling caused by aged or damaged speakers, and preserves original mounting location and connector compatibility. The part is often searched for by its product number, making it easy to identify when ordering replacements for Citroën C1 and Peugeot 107 models.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C1 (First Series), Peugeot 107 (First Series)
• Product Codes: 86160-0H010
• Additional Numbers: 6562L7, 86160-010
• Location: Dashboard / Instrument Panel Speaker
• Compatibility: First generation C1/107 series, vehicles produced up to 2013 (verify by part number)

Installation Recommendation

Before starting any work always disconnect the vehicle battery to avoid short circuits. Typical replacement steps:

1. Remove the appropriate dashboard trim panels and instrument cluster surround using trim tools to avoid damaging clips.
2. Unscrew the speaker mounting screws and carefully unplug the factory connector.
3. Install the replacement speaker into the original location, reconnect the connector and tighten screws to secure mounting without over‑torquing.
4. Reconnect the battery and test the audio system at low volume to confirm correct operation before reassembling all trim.

Use correct tools and take care with fragile plastic trim. If the radio is integrated with vehicle electronics, test the speaker function before final reassembly.

Why This Part Fails Most Often

• Age and Wear: Foam surrounds and cones degrade with time, causing distortion or loss of sound.
• Moisture Ingress: Condensation or water exposure can corrode voice coils and connectors.
• Overload or Electrical Faults: Amplifier faults or short circuits can blow the speaker.
• Mechanical Damage: Vibrations, rattles or impact during previous repairs can damage the speaker or its mounting.

Signs You Need Replacement

• Distorted or buzzing sound from the instrument panel area.
• No sound from the affected speaker position while other speakers work normally.
• Intermittent sound, crackling, or audible rattle at certain volumes.

Notes for Mechanics and DIYers

This speaker is a direct replacement component; when ordering, reference the product numbers above to ensure compatibility. Keep trim clips and fasteners organized during disassembly to ensure a clean reinstallation. If sound issues persist after replacement, inspect wiring, connectors and the radio unit for faults.

This dashboard panel is designed for the first generation of Citroën C1, Peugeot 107, and Toyota Aygo models manufactured up to 2014. Featuring a sleek black Mistral color, it provides a professional and clean finish to your vehicle’s interior.

If you need a reliable replacement part for your Citroën, Peugeot, or Toyota, this dashboard panel ensures both functionality and aesthetics without compromise. It’s an original part engineered to fit your vehicle perfectly, giving your car a refreshed look while maintaining its factory quality.

Technical Information

• Manufacturer: PSA – Citroën & Peugeot
• Model: Citroën C1, Peugeot 107, Toyota Aygo
• Product Codes: 55405-0H010
• Additional Numbers: 8211SG

Installation and Usage

The installation process is straightforward and can be performed by professional mechanics as well as skilled DIY enthusiasts. This panel replaces the existing dashboard element easily and helps restore your vehicle’s interior to its original condition. Proper installation guarantees a secure fit and seamless integration with your car’s dashboard.

Dashboard panels can wear out or suffer damage over time due to exposure to sunlight, heat, or general wear and tear. Replacing them not only improves your car’s interior appearance but also helps preserve the functionality of controls and displays attached to the panel.

Benefits

Choosing this original dashboard panel means you get an authentic part matched perfectly to your vehicle’s specifications. The black Mistral finish complements the cabin design, providing a clean and modern look. Whether you are repairing a damaged dashboard or upgrading worn components, this part is a durable and visually appealing solution.

Secure this quality replacement panel today and ensure your Citroën C1, Peugeot 107, or Toyota Aygo remains equipped with the finest components available. This dashboard panel is more than just a replacement part – it’s an upgrade that enhances your vehicle’s interior experience.

This left front door speaker is a direct-fit replacement designed for Citroën C1 and Peugeot 107 models. Ideal for professional workshops and experienced DIYers, the unit restores clear midrange and treble response lost from worn or damaged factory speakers. The part is commonly searched by part numbers 86160-0H040 and B000614380, so listing those references helps you find the correct item quickly.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1, Peugeot 107
• Product Codes: 86160-0H040, B000614380
• Other Numbers: 86160-040

Function And Fitment

The speaker is intended for the Left Front (Driver’s Side) door and replaces the original equipment unit. It reproduces mid and high frequencies that are critical for vocal clarity and stereo imaging in the car audio system. The unit is supplied to match factory mounting points and connector style for straightforward installation on compatible vehicles.

How To Replace

• Remove the door trim panel following vehicle-specific procedure (careful with clips and plastic trim). Keep screws and clips organized.
• Peel back or remove the moisture/water shield to access the speaker.
• Unplug the speaker connector and remove mounting screws or bolts securing the speaker.
• Fit the new speaker into the original mounting. If required, transfer any adapter plates or brackets from the old unit.
• Connect the wiring, observing correct polarity (positive/negative) to avoid phase issues.
• Test the speaker at low volume before reassembling the door trim to confirm operation and polarity.
• Reinstall the moisture barrier and door panel, ensuring all clips and fasteners are secure.

Installation Recommendations

• Work On A Stable Surface With Appropriate Tools. Use trim tools to avoid breakage of plastic clips.
• Disconnect The Battery If You Will Be Working Near Airbag Components Or Extensive Electrical Work Is Required. For simple speaker swaps, disconnecting the negative terminal is a precaution many technicians follow.
• Check Wiring And Connector Condition. Corroded or loose connectors should be cleaned or replaced to ensure reliable contact.
• Maintain Correct Polarity. Reversing speaker polarity degrades sound quality and stereo imaging.
• Do Not Over-Tighten Screws. Use consistent torque to avoid deforming the speaker frame or door panel.

Common Failure Reasons

• Water Ingress From The Door or Window Seals Causing Cone Or Voice Coil Damage.
• Age-Related Wear Such As Foam Or Surround Deterioration.
• Mechanical Damage From Impact Or Improper Removal/Installation.
• Connector Corrosion Or Wiring Faults Leading To Intermittent Sound Or No Output.
• Overdriving From A Faulty Amplifier Or Head Unit Resulting In A Blown Voice Coil.

Notes For Professionals And DIYers

Part numbers 86160-0H040 and B000614380 are commonly used when searching for this speaker. Confirm visual match with the original unit (mounting holes, frame size, connector type) before installation. Testing the speaker operation before reassembly saves time in case of mismatches or faulty items.

This direct-fit replacement speaker is designed for the right front (passenger side) door of Citroën C1 and Peugeot 107 vehicles. It is commonly searched by part numbers 86160-0H020 and B000614280, making it easy to find for mechanics and DIY enthusiasts. The speaker restores clear midrange and bass reproduction in the front passenger area and is ideal when the original unit produces distortion, rattles, or has failed completely.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1; Peugeot 107
• Product Codes: 86160-0H020; B000614280
• Other Numbers: 86160-020

Compatibility

Fits first-generation Citroën C1 and Peugeot 107 models (common model years 2005–2014). It is a direct replacement for the right front door speaker and matches the factory mounting points and connector style used on these vehicles.

Function

The speaker reproduces audio signals from the head unit or external amplifier, providing midrange clarity and low-frequency support for the front passenger area. When operating correctly it reduces distortion and improves overall sound staging in the vehicle.

Typical Failure Causes

• Aging and Wear: Foam surrounds, spider, or cone material can degrade over time, causing loss of performance or rattling.
• Water Ingress: Door seals and drainage failures can allow moisture into the door cavity, damaging the speaker coil or cone.
• Electrical Issues: Overpowering from aftermarket amplifiers or short circuits can burn the voice coil and cause failure.
• Mechanical Damage: Impact or improper door panel removal/installation can deform the speaker frame or mounting, creating noise.

Installation Recommendations

• Prepare Tools: Torx/screwdriver set, trim removal tools, multimeter for polarity check, and mounting screws if required.
• Safety First: Disconnect the battery before starting work to avoid short circuits and accidental airbag deployment.
• Door Panel Removal: Carefully pry off door trim using plastic trim tools to avoid breaking clips. Remove any vapor barrier or insulation without tearing it irreparably.
• Remove Old Speaker: Unplug the speaker connector, unscrew the speaker from the door, and note wire polarity (positive/negative) for correct reconnection.
• Fit New Speaker: Align the speaker with factory mounting holes, secure with screws, connect the wiring with correct polarity and test audio at low volume before full reassembly.
• Final Checks: Verify there are no rattles or contact with the door panel or window mechanism. Reinstall vapor barrier and door trim ensuring all clips and fasteners are properly seated.

Why Choose This Part

Part numbers 86160-0H020 and B000614280 are widely used search terms among professionals and DIYers; using the correct code speeds up sourcing and fitment. This speaker is intended for a straightforward, cost-effective restoration of front-stage audio quality in Citroën C1 and Peugeot 107 vehicles.

Notes For Mechanics and DIYers

When replacing door speakers, always inspect door seals, drainage channels and amplifier/head unit settings to avoid repeat failures. If distortion persists after replacement, check the audio source and wiring for faults or poor grounding.

Product Overview

Replacement tweeter designed for the dashboard audio system of Citroën C1 and Peugeot 107. This compact high-frequency driver restores clarity and detail to factory audio systems, improving speech intelligibility and the upper range of music reproduction. Ideal for professional workshops and DIY mechanics looking for a direct-fit solution using the vehicle’s original mounting points and electrical connection.

Technical Information

• Manufacturer: Stellantis (Citroën, Peugeot)
• Model: Citroën C1; Peugeot 107
• Product Codes: 86160-0H030; B000728380
• Additional Numbers: 86160-030; B000728380

Installation Recommendations

Typical replacement procedure for experienced mechanics and competent DIYers:

• Remove dashboard trim pieces or speaker grille using appropriate trim tools to avoid damage to plastic parts.
• Unscrew or unclip the old tweeter from its mounting location and gently disconnect the electrical connector.
• Connect the new tweeter to the original connector and secure it with the original screws or clips.
• Refit trim and verify correct seating. Test the speaker with the audio system at moderate volume before final reassembly.

Recommended tools: trim removal tools, Torx/Phillips screwdriver set, and a multimeter for quick continuity checks if needed. Observe standard safety practices when working on vehicle interiors; avoid force on plastic tabs and connectors.

Common Failure Reasons

Tweeters typically fail due to electrical overload (amplifier clipping or short circuits), long-term thermal stress, moisture ingress from leaks, or mechanical damage from improper removal. Loss of high-frequency output, rattling, or complete silence are common symptoms indicating a faulty tweeter. Replacing a failed tweeter often restores balance to the factory soundstage without needing to change other components.

Notes For Professionals

Part numbers and fitment information are provided to help locate the correct replacement quickly. Many technicians search by OEM code (86160-0H030 / B000728380) when ordering. When installing in vehicles with upgraded audio systems, verify impedance and power handling compatibility with the existing amplifier to avoid repeated failures.

This Clarion OEM-style radio with built-in CD player is a direct-fit replacement for the factory head unit in early Citroën C1, Peugeot 107 and Toyota Aygo models. Frequently searched by part numbers 86120-0H010 and 6564K6, this unit restores in-car radio reception and CD playback while using the vehicle’s original mounting points and wiring harness. The description and codes make this item easy to find for professional mechanics and DIY enthusiasts looking for a reliable OEM replacement.

Technical Information

• Manufacturer: Clarion (Stellantis OEM)
• Model: Citroën C1 / Peugeot 107 / Toyota Aygo (Up To 2013)
• Product Codes: 86120-0H010, 6564K6
• Additional Numbers: NFP

Compatibility

Fits factory radio locations of Citroën C1, Peugeot 107 and Toyota Aygo models produced up to 2013. Often searched and ordered by the part numbers listed above — include these codes when sourcing or cross-referencing the unit.

Function And Practical Details

The unit provides standard car radio reception and CD playback using the vehicle’s OEM connectors. It is designed to integrate into the original dashboard opening and typically connects to the factory antenna, power and speaker harness. Expect standard controls for tuning and CD operation identical to other OEM Clarion single-DIN units of the era.

Installation Recommendation

• Disconnect the vehicle battery before starting work to avoid short circuits and protect vehicle electronics.
• Remove the trim panels and use appropriate radio removal tools to unclip the factory unit without damaging the dash.
• Unscrew mounting brackets, gently pull the unit out and disconnect the antenna, power/speaker harness and any auxiliary connectors.
• Compare connectors and harness pinout. If the vehicle uses an ISO adapter, fit an appropriate adapter or wiring loom to avoid cutting factory wiring.
• Install the replacement unit by reversing removal steps. Secure mounting bolts, reconnect all plugs and test radio, speakers and CD operation before reassembling trim.
• Check the corresponding in-line fuses if the unit does not power up. Ensure the antenna connection is secure for best reception.
• Use correct removal/insertion tools to prevent damage to trim or radio chassis. If steering wheel audio controls are present, a compatible interface may be required to retain their function.

Why This Part Fails Most Often

• Mechanical Wear Of The CD Mechanism: Repeated use leads to laser or motor wear, causing read errors or failure to load discs.
• Age-Related Electronic Faults: Electrolytic capacitor degradation and solder joint fatigue can cause intermittent power loss or audio failures after many years in service.
• Connector Corrosion And Moisture Ingress: Exposure to humidity or water leaks can corrode contacts or damage internal circuitry.
• Physical Damage Or Impact: Dashboard impacts during removal/installation or vehicle incidents can deform the chassis or damage internal components.
• Fuse Or Wiring Issues: Blown fuses, poor grounds or damaged speaker wires are common causes of a unit appearing faulty when the radio itself is intact.

Practical Tip For Mechanics And DIYers

When replacing an OEM head unit, always cross-reference the part numbers 86120-0H010 and 6564K6 to ensure fitment and ordering accuracy. Keep the factory connector shapes and harness adapters handy to avoid unnecessary splicing. Test all functions (radio, CD, speakers and any steering wheel controls) before refitting the trim.

Search And Ordering Keywords

Citroën C1 Radio, Peugeot 107 Radio, Toyota Aygo Radio, Clarion CD Player, OEM Radio 86120-0H010, OEM Radio 6564K6, Car Radio Replacement

Featuring a user-friendly interface and clear display, this car radio provides seamless integration into your vehicle’s dashboard. The device not only plays CDs but also includes integrated speakers, ensuring that you enjoy your favorite music and podcasts on the go.

As part of standard vehicle wear and tear, car radios often need replacement due to typical issues such as electrical malfunctions, physical damage, or outdated technology. It’s advisable to consider replacing your car radio every few years or when you notice a decline in performance.

Technical Information

• Manufacturer: CLARION
• Model: 86120-0H010
• Product Codes: 6564K6
• Other Numbers: PSA CITROEN PEUGEOT