Digital control panel heating and air conditioning for Peugeot 308. This is the original part of the PSA concern with the designation 96850724XT / 6452J4. The ideal replacement when the original panel shows errors, does not respond to the press of buttons, the fan control or the underflies does not work.

The panel is used to control the temperature, air distribution, fan intensity and other HVAC functions. Thanks to the same connectors, the assembly is usually plug & play – just replace the original unit for this with the same code. We always recommend comparing the part numbers (96850724XT, 6452J4) with a label of your original part for 100% compatibility.

when the panel to change

• Unact or “dead” buttons, non -functional roller/driver
• Incorrect or fluctuating temperature and fan control
• shutting down or non -functional backlight, unreadable display
• Air conditioning error messages without demonstrable compressor/fan defects

mounting tips for car mechanics

• Before dismantling, disconnect the minus pole of the battery for BSI.
• Remove the center console frame, release the brackets and pull out the panel (usually Torx screws).
• disconnect the connectors, put the new unit with the same code and check the HVAC features.
• After assembly, it is advisable to delete any error codes with diagnostics and perform a functional test of flaps/fan.

Compatibility
Designed for Peugeot 308 first generation (T7). Suitable for hatchback, SW and CC within the 308 T7 model series. Usually coding is not required; The decisive factor is to match the part number given on the label of the original unit.

Technical information
Manufacturer: PSA / Peugeot (OE)
Model: Peugeot 308 (T7, approx. 2007–2013), incl. SW and CC
product codes: 96850724XT; 96850724XT-00; 6452J4; 6452.J4
additional numbers: 96 850 724 XT; 96850724XT00; 6452 J4

This is the original part used. The condition corresponds to normal wear wear. Always compare the numbers and photos with your original panel for the correct selection.

This HVAC control panel is a direct-fit control interface for Peugeot 308 (T7) models, providing intuitive control over heating, ventilation and air conditioning functions. Designed for professional workshops and experienced DIY mechanics, the unit is often searched by its product codes (96718462XT, 96718462XT-00, 6452S2). The clear layout and robust connectors make it a common replacement part when the original control stops responding, displays faults, or loses certain functions.

Function And Application

The unit governs cabin temperature, air distribution, fan speed, air recirculation and air conditioning engagement. It interprets user inputs and sends commands to the blower motor, blend/stepper motors (or servos), AC compressor clutch and related climate actuators. The panel usually includes an integrated display or LED indicators and electrical connectors that communicate with the vehicle’s climate and body control systems.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot) / Valeo
• Model: Peugeot 308 T7
• Product Codes: 96718462XT, 96718462XT-00, 6452S2
• Additional Numbers: 96718462XT-00 (alternate listing), 6452S2 (manufacturer/variant code)

Installation Recommendations

Before starting any work, disconnect the negative battery terminal to avoid short circuits and accidental airbag deployment. Typical replacement steps:

• Remove surrounding dashboard trim panels using proper plastic trim tools to avoid damage.
• Unscrew the retaining screws securing the control unit and gently pull the panel forward.
• Disconnect electrical connectors by releasing locking tabs—inspect connectors for corrosion or broken pins.
• Fit the replacement unit, reconnect all plugs and reassemble trim. Verify full function of all HVAC modes and fan speeds.

Most units are plug-and-play. However, if the vehicle has climate functions integrated with other modules, a diagnostic scan or reinitialisation may be required to restore full operation. For complex cases, use professional diagnostic equipment.

Why This Part Fails Most Often

• Wear Of Controls: Repeated use can wear potentiometers, switches or rotary encoders, causing intermittent or lost control of fan speed and temperature selection.
• Moisture And Contamination: Spills or moisture ingress may corrode contacts or damage internal electronics.
• Connector Issues: Broken pins, loose connections or oxidised terminals cause communication faults between the panel and climate actuators.
• Display/Backlight Failure: LED or display components can fail, making settings unreadable though functions may still work.

Practical Tips For Mechanics And DIYers

• When diagnosing, check fuses and wiring to the blower motor and sensors before replacing the control unit to avoid unnecessary swaps.
• Compare product codes on the faulty unit with the replacement to ensure identical electrical connectors and feature set.
• Keep a clean work area and label connectors if you remove multiple plugs to prevent misrouting on reassembly.

Keywords: Peugeot 308 HVAC Control, Heater Control Unit, Climate Control Panel 96718462XT, 6452S2, Peugeot 308 T7 climate control.

Product Overview

This High-quality Heating and Air Conditioning Control module is specifically designed for the Peugeot 308, ensuring optimal climate control for your vehicle. As an essential component, it allows for precise adjustment of heating and cooling systems, enhancing passenger comfort.

Compatibility

This product is compatible with Peugeot 308 models. It is suitable for both professional mechanics and DIY enthusiasts looking to repair or upgrade their vehicle’s climate control system.

Common Issues

This unit typically fails due to wear and tear from regular use or electrical issues leading to malfunctions. Symptoms of failure may include unresponsive controls, incorrect temperature settings, or fluctuating fan speeds.

Installation Information

Replacing the heating and air conditioning control module is straightforward. The existing unit can usually be accessed by removing the dashboard cover. It is recommended to consult the vehicle’s manual for specific instructions regarding your model.

Technical Information

Manufacturer: PSA CITROEN PEUGEOT
Model: Peugeot 308
Product Codes: T1000220K, 6452G1
Additional Numbers: 6452 G1