C2 and C3 I – Used Parts Vendor https://www.usedpartsvendor.com Citroën Peugeot spare parts Tue, 16 Jun 2026 02:12:13 +0000 en-GB hourly 1 https://wordpress.org/?v=7.0 ATE ABS Pump Citroën C2 C3 9651412080 10.0207-0011.4 https://www.usedpartsvendor.com/electro-components/control-units/abs-and-esp/abs-esp-modules/207-abs-esp-modules/abs-pump-ate-citroen-c2-c3-9651412080-10-0207-0011-4/ Sat, 14 Feb 2026 03:00:56 +0000 https://www.usedpartsvendor.com/uncategorized/abs-pump-ate-citroen-c2-c3-9651412080-10-0207-0011-4/ Control Module, ABS Pump, Unit, ABS Block ATE Citroën C2 and C3, Peugeot 207. Supplied with a piece of wiring.

This ABS/ESP control unit by ATE is a direct-fit replacement widely used on Citroën C2, Citroën C3 (including C3 Pluriel) and Peugeot 207 vehicles. It is often searched for by part numbers such as 9651412080 or 10.0207-0011.4, so listing these codes in your search will help you find the correct unit quickly. The module restores electronic brake control and ABS functionality, improving active safety and brake stability. Supplied with a length of wiring to simplify the electrical connection during installation—appropriate for professional garages and experienced DIY technicians.

Technical Information

  • Manufacturer: ATE
  • Model: Citroën C2, Citroën C3, Citroën C3 Pluriel, Peugeot 207
  • Product Codes: 9651412080; 10.0207-0011.4; 10.0970-1108.3
  • Other Numbers: 4542F3; 4542F4; 4541G4; 4541G5

How It Is Replaced (High-Level)

Replacement of the ABS pump and control module is a mechanical and electrical job best handled by trained technicians or experienced DIYers with appropriate tools. Typical steps include:

  • Disconnect The Battery To Prevent Electrical Damage And Avoid Unintended System Inputs.
  • Access The Unit—Usually Located In The Engine Bay Near The Brake Master Cylinder/Firewall. Remove Any Covers Or Brackets As Needed.
  • Label And Cap Brake Lines Before Removal To Prevent Fluid Loss And Contamination. Use Correct Line Wrenches To Avoid Rounding Fittings.
  • Disconnect Electrical Connector(s) And Remove Mounting Bolts To Extract The Module.
  • Install New Unit Using The Supplied Wiring Piece Where Required, Reconnect Brake Lines, Torque Fasteners To Manufacturer Specifications, And Reconnect Electrical Connectors.
  • Bleed The Brake System Thoroughly. After Installation, Use A Diagnostic Tool To Clear Fault Codes And Perform Any Required ABS Pump Activation/Initialization Routines.

Installation Recommendations

  • Replace Brake Fluid When Replacing The ABS Unit To Remove Moisture And Contaminants That Can Damage The New Module.
  • Use A Proper Diagnostic Scanner Capable Of ABS/ESP Procedures To Clear Codes And Run Pump Self-Test Sequences After Installation.
  • Protect Exposed Brake Lines And Electrical Connectors From Dirt During The Swap; Cap Lines Immediately After Disconnection.
  • Check Wheel Speed Sensors And Wiring Harnesses—A Faulty Sensor Or Damaged Connector Can Cause Premature Stress On A New ABS Module.
  • If You Are Unsure About Bleeding Or Calibration, Have The Final Steps Performed At A Workshop With The Required Equipment.

Why This Part Fails Most Often

Common causes of ABS module failure include moisture Ingress And Corrosion At Electrical Connectors, Internal Pump Motor Wear, Contaminated Or Moisture-Laden Brake Fluid, And Thermal Or Mechanical Stress Over Time. Symptoms That Indicate A Faulty Unit Include An Illuminated ABS Warning Light, Intermittent Or Permanent Loss Of ABS Function, Audible Pump Noise During Normal Driving, And Altered Brake Pedal Feel Or Performance.

There Is No Fixed Replacement Interval—Many Units Last For Years Or Well Over 100,000 Km Under Normal Conditions. However, cars Exposed To Road Salt, Frequent Short Trips, Or Infrequent Brake Fluid Changes Are More Likely To Experience Early Failures.

]]> ABS ATE Citroën C3 Peugeot 207 9663945580 10.0207-0105.4 4541FX https://www.usedpartsvendor.com/electro-components/control-units/abs-and-esp/abs-esp-modules/c3-ii-abs-esp-modules/abs-ate-citroen-c3-peugeot-207-9663945580-10-0207-0105-4-4541fx/ Thu, 15 Jan 2026 03:03:38 +0000 https://www.usedpartsvendor.com/uncategorized/abs-ate-citroen-c3-peugeot-207-9663945580-10-0207-0105-4-4541fx/ Control module, ABS pump, ABS cube ATE CITROEN C3, C3 II also fits PEUGEOT 207
Hydraulic brake control block
With a piece of wiring

Part description

This part is an ABS ATE module (control module with hydraulic block/pump), intended for the brake system of the Citroën C3, C3 II and, as indicated, also the Peugeot 207. The ABS unit takes care of controlling the pressure in the brakes during emergency braking and helps maintain the car’s controllability.

A piece of wiring is included, making it easy to connect and check the connectors when changing. Parts of this type are often searched by number – so we list all known codes below.

Technical information

  • Manufacturer: ATE
  • Model: Citroën C3, Citroën C3 II, Peugeot 207
  • Other numbers: 4541FY, 4541FX, 1682607180, 4542N2, 4542N1, NFP

Product codes

  • Product codes: 9663945580, 10.0207-0105.4, 10.0970-1146.3, 4541FY, 4541FX, 1682607180, 4542N2, 4542N1, NFP

Installation recommendations

Generally/typically, replacing the ABS module/pump with the hydraulic block is an intervention in the braking system. The exact procedure may vary depending on the specific car design and equipment.

1) Before assembly

  • Compare with the old part: all numbers on the label (eg 9663945580, 10.0207-0105.4), type of connectors and their fuses.
  • Check the condition of the connectors and the attached piece of wiring (undamaged pins, no corrosion, no torn insulation).
  • Visually check the hydraulic block body and threads/brake lines (no cracks or deformations).
  • Prepare a clean working environment in advance – dirt in the system causes problems with brakes.

2) Necessary tools and materials

  • Normal set of gola/ratchets and bits, screwdrivers
  • Wrenches for brake pipes (to minimize screwing off)
  • Brake line plugs/seals (to limit fluid leakage and dirt ingress)
  • Cleaning agent for electrical contacts, rags
  • Suitable equipment for bleeding the brakes (according to your practice and possibilities)

3) Step-by-step assembly procedure

  1. Secure the vehicle against movement and disconnect the battery.
  2. Locate the ABS unit and access it by removing the obstructing covers (depending on the model of the car).
  3. Mark the brake lines (e.g. with tape) to avoid confusion during reassembly.
  4. Disconnect the unit’s electrical connectors (including any wiring) and check the locking mechanisms.
  5. Carefully loosen the brake fittings/lines; continuously plug open ends to prevent dirt from entering the system.
  6. Unfasten the drive and remove the old module.
  7. Install the new used ABS module in the holder and tighten the fastening (without changing the threads).
  8. Screw the brake lines back in – first by hand so the threads don’t cross, then tighten with a suitable wrench.
  9. Connect the electrical connectors; make sure the contacts are clean and the fuses are properly engaged.
  10. Refit the dismantled covers/parts in the engine compartment (depending on the car).
  11. Bleed the brake system according to the normal procedure for the car and check the brake fluid level.
    • 4) Post-assembly checks and test drive/function verification

      • Check the tightness of all brake line connections (dry connections, no leaks).
      • Verify firm operation of the brake pedal and basic operation of the brakes at low speed in a safe place.
      • If you have a diagnostic, perform an ABS/ESP system check and verify that there are no associated fault reports.

      5) The most common assembly mistakes + how to avoid them

      • Replacing brake lines → always mark them before dismantling.
      • Broken brake pipe fittings → use brake pipe wrenches and loosen with sensitivity.
      • Impurity in the brake system → blind, keep clean, leave the line open for as short a time as possible.
      • Poorly engaged connector / pin corrosion → visual inspection, contact cleaning, connector fuse check.
      • Insufficient venting → follow best practice for the car and check pedal operation after venting.

      Reasons why the part is damaged

      • Moisture and corrosion of connectors (increased transition resistance, communication failures).
      • Electronic aging and temperature stress in the engine compartment (cracked connections, unstable function).
      • Brake fluid contamination and internal clogging of the hydraulic block.
      • Mechanical damage (impact, unprofessional handling during brake repair).
      • Electrical overvoltage or bad grounding in the vehicle installation.
      ]]> ABS pump Citroën C2 C3 9641965380 10.0970-1106.3 10.0207-0001.4 https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-pump-ate-citroen-c2-c3-9641965380-10-0970-1106-3-10-0207-0001-4/ Sun, 23 Feb 2025 03:07:20 +0000 https://www.usedpartsvendor.com/uncategorized/abs-pump-ate-citroen-c2-c3-9641965380-10-0970-1106-3-10-0207-0001-4/ Looking for a dependable replacement ABS pump and control module for your Citroën C2 or C3? This ATE ABS pump, designed specifically for first-generation Citroën C2 and C3 models, plays a vital role in your vehicle’s braking system, ensuring safety and control.

      The unit comes with a segment of wiring harness, facilitating quicker and easier installation for both professional mechanics and DIY enthusiasts. It is a critical component of the Anti-lock Braking System (ABS), preventing wheel lock-up during heavy braking and enhancing vehicle stability on slippery surfaces.

      Technical Information

      • Manufacturer: ATE
      • Model: Citroën C2, Citroën C3 First Generation
      • Product Codes: 9641965380, 10.0970-1106.3, 10.0207-0001.4
      • Additional Numbers: 4542F3, 4542F4, 4541G4, 4541G5

      This part is essential for safe and efficient braking, especially under challenging driving conditions. Regular inspection and timely replacement of the ABS pump help maintain optimum brake performance and vehicle safety. Our fully functional ATE ABS pump and control module offers a cost-effective solution without compromising quality.

      When installing this component, ensure careful connection of the wiring harness and secure mounting within the vehicle. Consulting a specialist or following the vehicle’s specific repair manual is advisable to guarantee proper installation. This unit meets the necessary standards and functions reliably as an original equipment part.

      For further assistance or to purchase this critical brake system component, please contact our sales department. We are committed to helping you find the right solution to ensure your vehicle’s safety and reliability.

      ]]>             ATE ABS/ESP module for Citroën C3 – part numbers: 9649028880, 10.0206-0101.4, 10.0960-1125.3, 4541C1 (used) https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-esp-ate-citroen-c3-9649028880-10-0206-0101-4-10-0960-1125-3-4541c1-2/ Fri, 22 Nov 2024 03:24:20 +0000 https://www.usedpartsvendor.com/uncategorized/abs-esp-ate-citroen-c3-9649028880-10-0206-0101-4-10-0960-1125-3-4541c1-2/ Product Overview

      This ABS ESP control module and pump unit from ATE is designed specifically for Citroën C3 Pluriel models equipped with a 1.6L 16-valve Sensodrive engine. The unit plays a critical role in the vehicle’s braking and stability systems by managing the Anti-lock Braking System (ABS) and Electronic Stability Program (ESP), ensuring enhanced safety during driving.

      Application and Compatibility

      Compatible with Citroën C3 Pluriel 1.6V 16V Sensodrive versions, this module is often sought under product codes 9649028880, 10.0206-0101.4, and 10.0960-1125.3, and OEM references such as 4541C1. It is crucial for mechanics and car enthusiasts repairing PSA group vehicles, especially Citroën and Peugeot models equipped with similar braking systems.

      Replacement and Maintenance

      The ABS ESP module may fail due to electrical issues, wear of internal pump components, or sensor malfunctions, which can lead to warning lights on the dashboard and reduced braking performance. Replacing this module requires disconnecting the battery, removing the old unit along with its wiring harness, and installing the new one carefully to ensure full system integration and calibration.

      Technical Information

      • Manufacturer: ATE
      • Model: Citroën C3 Pluriel 1.6V 16V Sensodrive
      • Product Codes: 9649028880, 10.0206-0101.4, 10.0960-1125.3
      • OEM Numbers: 4541C1, 454190, 4541S0, 454294, 454295

      Additional Details

      The module comes with a section of the cable harness to facilitate connection. Its integrated pump ensures effective brake fluid pressure modulation, vital for ABS and ESP functions. Proper installation guarantees restored vehicle safety and driving confidence.

      ]]>             ATE ABS/ESP module for Citroen C3 – 9649028880 / 10.0206-0101.4 / 10.0960-1126.3 / 4541C1 https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-esp-ate-citroen-c3-9649028880-10-0206-0101-4-10-0960-1126-3-4541c1-2/ Fri, 22 Nov 2024 03:24:08 +0000 https://www.usedpartsvendor.com/uncategorized/abs-esp-ate-citroen-c3-9649028880-10-0206-0101-4-10-0960-1126-3-4541c1-2/ Product Overview

      This ABS ESP ATE control module is designed specifically for Citroën C3 Pluriel models equipped with the 1.6L 16-valve Sensodrive engine. It combines the ABS control unit and the ESP pump, ensuring effective management of vehicle stability and braking performance. The module comes complete with a piece of wiring harness, facilitating easier installation during repairs or replacements.

      The ABS and ESP systems play critical roles in maintaining vehicle safety by preventing wheel lock-up during braking and enhancing traction control. Failure of the module can lead to warning lights on the dash and compromised braking efficiency. Common causes of failure include electronic faults and pump wear over time, which typically occurs after extended use or exposure to harsh conditions.

      Installation and Compatibility

      Replacement of this module requires disconnecting the old unit and its wiring harness carefully, then plugging in the new module and securing it correctly within the engine bay. This part is vital for technicians and experienced DIY enthusiasts performing brake control system repairs.

      Technical Information

      • Manufacturer: ATE
      • Model Compatibility: Citroën C3 Pluriel 1.6V 16V Sensodrive
      • Product Codes: 9649028880, 10.0206-0101.4, 10.0960-1126.3
      • Additional Codes: 4541C1, 454190, 4541S0, 454294, 454295
      ]]>             ATE ABS control module for Citroen C3 and Peugeot 207, part numbers 9662298480, 10.0207-0092.4, 4541FX https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-ate-citroen-c3-peugeot-207-9662298480-10-0207-0092-4-4541fx-2/ Sun, 26 May 2024 04:05:14 +0000 https://www.usedpartsvendor.com/uncategorized/abs-ate-citroen-c3-peugeot-207-9662298480-10-0207-0092-4-4541fx-2/ This ABS ATE Control Module is designed to fit Citroën C3 models from 2007 and Peugeot 207 vehicles, making it a reliable replacement for your braking system’s anti-lock function. The module includes the ABS pump and comes with a piece of wiring harness for seamless integration during installation.

      The ABS control module plays a crucial role in maintaining vehicle safety by preventing wheel lock-up during heavy braking, which improves steering control and reduces stopping distances, especially on slippery roads. Faults in this component can lead to ABS warning lights and compromised braking performance, so timely replacement is essential for safety and vehicle compliance.

      Replacing the ABS ATE module typically involves accessing the brake assembly and unplugging the old module’s electrical connectors before securing the new unit and connecting the wiring harness. While the ABS pump is robust, wear and electrical faults over years of use can necessitate replacement.

      Technical Information

      • Manufacturer: ATE
      • Model: Citroën C3 (2007), Peugeot 207
      • Product Codes: 9662298480, 10.0207-0092.4, 4541FX
      • Additional Numbers: 10.0970-1144.3, 4541Z9, 4541AA, 4542L2, 4542L1, 4542N1
      ]]>             Used ATE ABS Control Module for Citroën C3 / Peugeot 207 – Part No. 9666392580 / 10.0207-0200.4 https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-ate-citroen-c3-peugeot-207-9666392580-10-0207-0200-4-2/ Sun, 19 May 2024 04:04:41 +0000 https://www.usedpartsvendor.com/uncategorized/abs-ate-citroen-c3-peugeot-207-9666392580-10-0207-0200-4-2/ Product Overview

      This ABS ATE control module is designed for Citroën C3 (2007 models) and Peugeot 207, offering reliable brake system management. The module integrates the ABS pump and electronic control unit, which work together to monitor wheel speeds and modulate braking pressure to prevent wheel lock-up during urgent stops. It comes with a portion of the wiring harness to facilitate installation and ensure proper connectivity within the vehicle’s braking system.

      ABS modules like this are critical for maintaining vehicle safety and stability, especially during slippery or emergency braking conditions. Common reasons for ABS module failure include internal electrical faults, pump malfunction, or damage caused by moisture ingress. Regular maintenance and prompt replacement when signs of ABS warning lights appear can prevent braking issues and maintain optimal vehicle control.

      Technical Information

      • Manufacturer: ATE
      • Model Compatibility: Citroën C3 (2007), Peugeot 207
      • Product Codes: 9666392580, 10.0207-0200.4, 10.0970-1153.3
      • Additional Numbers: 4541FX, 4541FY, 1682607180, 4542N2, 4542L1, 4542N1

      Installation and Maintenance

      The ABS module is typically located near the brake master cylinder or wheel arch inside the engine bay. Replacing the unit involves disconnecting the battery, carefully removing the electrical connectors and brake lines, and mounting the new module with supplied wiring to ensure seamless integration. It is recommended to bleed the brake system after installation to remove any air pockets and restore full brake performance.

      ABS modules generally last many years but can fail due to wear, heat, or electronic faults. Symptoms of failure include the ABS warning light on the dashboard, inconsistent braking, or audible pump operation when inactive.

      This product ensures your vehicle’s braking safety systems function properly, providing peace of mind during daily driving and emergency maneuvers.

      ]]>             Used ATE ABS Control Module for Citroën C3 / Peugeot 207 – 9663945580 / 10.0207-0105.4 https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-ate-citroen-c3-peugeot-207-9663945580-10-0207-0105-4-2/ Sun, 19 May 2024 04:04:36 +0000 https://www.usedpartsvendor.com/uncategorized/abs-ate-citroen-c3-peugeot-207-9663945580-10-0207-0105-4-2/ Product Overview

      This ABS control module with integrated pump from ATE is designed for Citroën C3 (2007) and also fits Peugeot 207 models. It is a critical component of the vehicle’s anti-lock braking system, responsible for regulating brake pressure to prevent wheel lock during emergency braking, enhancing vehicle stability and safety on the road.

      Compatibility And Application

      The control module fits specifically Citroën C3 models from 2007 onward, as well as Peugeot 207 vehicles sharing the same ABS system architecture. Mechanics and DIY enthusiasts often search for this part using its OEM and aftermarket part numbers, including 9663945580, 10.0207-0105.4, and others listed below.

      Function And Replacement Details

      The ABS module combines the electronic control unit and the hydraulic pump. Over time, these modules can fail due to electrical faults or pump wear, often leading to warning lights on the dashboard and reduced braking performance. Replacing the unit restores proper ABS functionality, improving safety and vehicle control. The replacement involves disconnecting the battery, removing the faulty module with attached wiring harness, and installing the new unit, ensuring all connections are secure.

      Technical Information

      • Manufacturer: ATE
      • Model: Citroën C3 (from 2007), Peugeot 207
      • Product Codes: 9663945580, 10.0207-0105.4, 10.0970-1146.3
      • Additional Numbers: 4541Z9, 4541FX, 4541FY, 1682607180, 4542L2, 4542L1, 4542N1

      Included Components

      The module comes complete with the ABS pump and a section of the wiring harness, facilitating straightforward installation and compatibility with the vehicle’s existing electrical system.

      Why Choose This Module?

      Opting for this genuine ATE ABS module ensures reliable braking performance and long-term durability. It’s ideal for professional mechanics and experienced car owners performing ABS maintenance or repairs on PSA group vehicles.

      ]]>             ABS Pump ATE Citroën C2 C3 9652182680 10.0970-1118.3 10.0207-0016.4 https://www.usedpartsvendor.com/electro-components/control-units/abs-and-esp/abs-esp-modules/207-abs-esp-modules/abs-pump-ate-citroen-c2-c3-9652182680-10-0970-1118-3-10-0207-0016-4/ Thu, 11 Jan 2024 05:01:04 +0000 https://www.usedpartsvendor.com/uncategorized/abs-pump-ate-citroen-c2-c3-9652182680-10-0970-1118-3-10-0207-0016-4/ Product Overview

      ATE ABS pump and control module for Citroën C2 and C3 models. This unit integrates the hydraulic pump, modulator valves and electronic control to manage anti-lock braking during wheel slip events. It is supplied with part of the wiring harness and is intended as a direct-fit replacement for compatible PSA vehicles.

      Key Benefits

      • Restores ABS functionality and braking stability under emergency braking conditions.
      • Direct-fit for listed Citroën models, reducing installation time for workshops and skilled DIYers.
      • Includes pump motor, modulator and control electronics — supplied with a piece of wiring harness for easier connection.

      Fitment And Compatibility

      Designed primarily for Citroën C2 and Citroën C3 models within PSA applications. Commonly searched by part numbers, so customers often find this unit under codes such as 9652182680 or the ATE references 10.0970-1118.3 and 10.0207-0016.4. Verify vehicle compatibility with VIN or OEM cross-reference before ordering.

      Installation And Replacement

      A competent mechanic or experienced DIYer should perform installation. Typical replacement steps include disconnecting the vehicle battery, securing and protecting brake lines to avoid contamination, disconnecting electrical connectors, removing mounting bolts and replacing the ABS unit. Brake system bleeding and fault-code clearing with a diagnostic tool are required after installation to ensure correct ABS operation.

      Common Faults And Service Life

      ABS units may fail due to internal pump motor wear, electrical faults, corroded connectors, or contamination of brake fluid. Exposure to moisture and road salts accelerates corrosion and electrical issues. Service life depends on driving conditions and maintenance; failures are often associated with high mileage, fluid contamination or damage to wiring and connectors.

      Technical Information

      Manufacturer: ATE

      Model: Citroën C2, Citroën C3

      Product Codes: 9652182680, 10.0970-1118.3, 10.0207-0016.4

      Other Numbers: 4542F3, 4542F4, 4541G4, 4541G5

      Notes For Buyers

      Always confirm part numbers and vehicle compatibility before purchase. After replacement, perform a full brake bleed and use a diagnostic scanner to clear ABS fault codes and verify system operation. If in doubt, consult a professional workshop to ensure safe installation and system calibration.

      ]]>             ABS ESP ATE Control Unit Citroën C3 9649028880 10.0206-0101.4 4541C1 https://www.usedpartsvendor.com/chassis-and-axles/brake-system/abs-esp-modules-brake-system/c2-and-c3-i-abs-esp-modules-brake-system/abs-esp-ate-citroen-c3-9649028880-10-0206-0101-4-4541c1-2/ Fri, 09 Jun 2023 04:10:17 +0000 https://www.usedpartsvendor.com/uncategorized/abs-esp-ate-citroen-c3-9649028880-10-0206-0101-4-4541c1-2/ ATE ABS/ESP Control Module designed for Citroën C3 Pluriel (1.6 16V Sensodrive). Searchable by primary OE: 9649028880 and alternative references 10.0206-0101.4, 10.0960-1125.3, 454190, 4541C1, 4541S0, 454294, 454295. This unit combines the electronic control module with the hydraulic pump used by the ABS and ESP systems.

      Function

      The ABS/ESP control unit continuously monitors wheel speed sensors and driver inputs to modulate brake pressure via the hydraulic pump and valves. During wheel slip or emergency braking the module reduces individual wheel pressure to maintain vehicle stability and shorten stopping distances. The pump and valve block restore pressure when required and provide anti-lock braking and electronic stability interventions.

      Fitment And Compatibility

      Primary fitment: Citroën C3 Pluriel 1.6 16V with Sensodrive transmission. The part number 9649028880 is used across several PSA small-car platforms; always verify compatibility using the OE numbers listed above before ordering.

      Replacement And Installation Notes

      1. Park the vehicle on a level surface, isolate the battery negative terminal to prevent electrical damage.
      2. Locate the ABS/ESP unit (typically mounted in the engine bay close to the firewall) and protect brake lines to avoid fluid loss.
      3. Disconnect electrical connectors and carefully loosen brake line fittings, catching any brake fluid and preventing contamination.
      4. Unbolt the module from its bracket and remove. Fit the replacement unit, torque fasteners to manufacturer values and reconnect wiring harness.
      5. Refill and properly bleed the brake system to remove air from all circuits. Clear fault codes with a diagnostic tool and confirm proper ABS/ESP operation with a test drive.

      Common Failure Modes

      Typical causes of ABS/ESP unit failure include internal pump wear, relay or valve faults, electrical connector corrosion, moisture ingress and damaged wiring. Symptoms often include ABS or ESP warning lights on the dashboard, intermittent braking feel, or fault codes relating to pump motor circuits or valve control.

      Condition And Supply

      This specific unit is supplied with a piece of the wiring harness and is stated as tested and fully functional by the supplier. It is sold as a direct replacement for matching OE numbers; ensure cross-reference before installation.

      Technical Information

      • Manufacturer: ATE
      • Model: Citroën C3 Pluriel 1.6 16V Sensodrive
      • Product Codes: 9649028880, 10.0206-0101.4, 10.0960-1125.3
      • Other Numbers: 454190, 4541C1, 4541S0, 454294, 454295
      ]]>