Original Bosch ABS/ESP control unit (so-called ABS cube, hydraulic block with ECU) for Peugeot cars. The part is taken from a Peugeot 3008 2.0 HDi (RHE), year 2009. The unit has been tested and is fully functional. Thanks to the mentioned codes, it is easy to find and suitable for replacing a faulty module in vehicles with the same equipment.

This ABS/ESP module ensures the stability of the car, shortens the braking distance during emergency braking and actively regulates the pressure in the brake system. Typical symptoms of a defect in the original unit are the lighting of the ABS/ESP lights, error codes of the pump or pressure sensors and limited function of the brake assistants. By replacing it with a correctly matched part according to the module number, these problems are reliably eliminated.

Assembly: always disconnect the battery before disassembly. After the mechanical replacement and reconnection of the brake pipes, it is necessary to bleed the system correctly (ideally with the help of diagnostics – service function for bleeding ABS/ESP) and perform the basic settings/telecoding of the unit according to the car’s equipment. Calibrating the steering wheel angle sensor and checking the wheel sensors is recommended. DiagBox/PP2000/Lexia diagnostics are suitable for PSA cars.

Always verify compatibility against part codes and connector designs. For ABS/ESP, matching the numbers of Bosch and PSA and the same arrangement of the brake outlets is essential. This piece is intended especially for the first generation Peugeot 3008/5008 with corresponding equipment.

Technical information

• Manufacturer: Bosch (ABS/ESP control unit + hydraulic block)
• Model: Peugeot 3008 I (T84), Peugeot 5008 I (T87); typically years of production 2009-2016 – check compliance according to the codes
• Product codes: Bosch 0265951325, 0265230879
• Other numbers: PSA 9666848380, 9664532380, 4541.NQ, 4541.NR, 1607510480

A used original Bosch part offers a quality and cost-effective solution compared to a new unit. If your vehicle is reporting ABS/ESP errors and the numbers on the plate match, this unit is a good candidate for replacement. For trouble-free installation, we recommend installation by an experienced mechanic and subsequent adjustment via diagnostics.

ECU/control unit and hydraulic block ABS/ESP for Peugeot 3008 I and 5008 I. Complete “ABS cube” including pump – ideal replacement for ABS/ESP errors, pump disorders or unit communication. It comes from the Peugeot 5008 1.6 E-HDI 9hr (2011) with a robotic transmission, the part has been tested and is fully functional.

This unit ensures the control of braking pressure and stabilization functions (ABS/ESP). Usually, ABS/ESP lights light up when failure, and a braking system failure is displayed on the dashboard. Typical manifestations are non -functional pump, internal defect of the control unit or loss of communication. Replacing the complete unit (ECU + Hydraulika) is the fastest way to restore a full function.

Compatibility: primarily for Peugeot 3008 I and 5008 I. The decisive is the match of the part and design of the car (motorization, gearbox, equipment – the presence of ESP, type of sensors). We recommend comparing all numbers listed on the label with your original work. This particular piece comes from version 1.6 E-HDI 9hr with robotized gearbox, but use is also possible for other variants if they agree codes.

Assembly recommendations: disconnect the battery before work, then replace the complete block and perform careful venting of the brake system (ideally with the activation of pumps and valves through diagnosis). For PSA cars, it is necessary to make telekoding/variant settings and any basic calibration (eg steering wheel sensor) in diagnostics diagnostics, especially if the software version or equipment configuration.

Status and origin: used original part removed from the car operated, tested – fully functional. Appropriate as a direct replacement of your non -functional module if they agree with the numbers.

Technical information

• manufacturer: bosch
• Model: ABS/ESP Module (ECU + Hydraulic Block, “Cube ABS”)
• Product codes: 0265951738, 0265230304
• Other numbers: 9674677580, 1607510480, 4541VX, 4541VY

Why choose this episode: Original solutions with certainty of proper functions and precise buildings, verified compatibility in valid codes and real operating piece from the PSA platform. If you have doubts, send us VIN or photos of your module label – you will check the match before assembly.