High-quality replacement fuel filler cap cover designed for Citroën C4 II (B7). This cover restores the exterior finish and protects the fuel filler area from dirt, moisture and mechanical damage. Ideal for professional workshops and DIY enthusiasts who look for an exact-fit part referenced by OE numbers. Compatible paint finish EZR (Grey Aluminium) ensures a factory-like appearance after installation.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C4 II (B7)
• Product Codes: 9687310880, 1517J1, 1518F9
• Additional Numbers: Color Code EZR – Grey Aluminium Paint

Fitment And Function

The fuel filler cap cover (fuel door/fuel flap) conceals and protects the fuel filler neck and cap. It mounts to the vehicle body via hinge and retaining clips or screws and, where applicable, operates with a spring or latch mechanism integrated into the flap or vehicle body. Correct fitment is essential to maintain fuel system protection and vehicle appearance.

Replacement Procedure

• Open the fuel filler door and inspect hinge and fasteners.
• Remove any retaining screws or plastic clips holding the old cover. In some cases an inner trim panel or access flap must be removed to reach fasteners.
• Detach the old cover from the hinge carefully to avoid breaking clips; keep any reusable screws.
• Position the new cover, engage the hinge and secure with original or replacement fasteners.
• Check alignment and operation of the door: it should close flush with the body and latch smoothly.

Installation Recommendations

• Use plastic trim tools to avoid paint damage when removing clips or trim panels.
• Replace any brittle clips or worn screws to ensure a secure fit and prevent rattles.
• Before final tightening, verify the door alignment and even gap to the surrounding bodywork.
• Clean mating surfaces and, if needed, touch up paint around the edge to protect against corrosion.
• For best result, perform installation on a level surface and avoid forcing the hinge to prevent breakage.

Common Failure Reasons

• Broken Hinge Or Clips: Most common cause—plastic hinges and retaining clips become brittle with age or after impact.
• Mechanical Damage: Minor collisions, vandalism or careless refuelling can dent or crack the cover.
• Corrosion And Paint Degradation: Chipped paint allows corrosion to develop around the filler aperture and hinge points.
• Latch Or Spring Wear: Worn latch or weak spring can cause the door not to close or remain secure.

By replacing a damaged fuel filler cap cover with the correct OE-coded part (9687310880 / 1517J1 / 1518F9) in color EZR, you restore appearance and protect the fuel filler area from further damage—important for both resale value and long-term body integrity.

Overview

This painted fuel filler cap cover is a direct-fit exterior part for the Peugeot 3008 first generation. It restores the original appearance of the fuel door area, protects the filler neck from dirt and moisture and maintains a factory-matched finish in color KGN (LAK BOURRASQUE). The cover is ideal for professional workshops and DIY mechanics looking for a correct-looking replacement by product code (useful when searching by part number).

Benefits

• Direct Fit For Peugeot 3008 I – Designed To Match Factory Mounting Points.
• Painted Finish KGN (LAK BOURRASQUE) – Ready To Install Without Additional Painting.
• Improves Vehicle Aesthetics And Protects Filler Neck From Contaminants.
• Availability In Multiple Colors – Useful For Color-Matched Repairs.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 3008 I (First Generation, 2008–2016)
• Product Codes: 9682803080, 1517G9
• Other Numbers: 151800, 1518E2

Fitment / Compatible Vehicles

Primary fitment: Peugeot 3008 (First Generation). When searching, customers commonly use the OEM part numbers 9682803080 or 1517G9 to ensure correct match. The filler neck housing referenced under code 1518E2 is a related item and may be required in case of damage to the internal assembly.

Installation Recommendation

Replacement is straightforward for most technicians and experienced DIYers. Typical steps:

• Open The Fuel Door And Inspect Fasteners, Hinge And Retaining Clips.
• If Held By Clips: Carefully Release Retaining Clips Using A Trim Tool Or Flat Screwdriver To Avoid Damaging Surrounding Paint.
• If Screwed: Remove Fasteners And Retain Them For Reinstallation.
• Align The New Cover With The Hinge And Snap Or Screw It Into Place. Check Free Movement And Closing Action.
• Verify That The Filler Cap And Neck Seal Properly After Installation.

Recommended Tools: Trim Pry Tool, Flat Screwdriver, Torx Or Metric Sockets (If Applicable). Work Carefully Around Painted Surfaces To Prevent Scratches.

Most Common Failure Reasons

• Impact Damage From Minor Collisions Or Parking Scrapes Causing Cracks Or Broken Hinge Points.
• Broken Or Worn Plastic Clips And Hinge Pins Leading To Looseness Or Detached Cover.
• Corrosion Or Dirt Build-Up Around The Filler Neck Causing Poor Fit Or Stiff Operation.
• Paint Damage Or Fading From Weather And UV Exposure, Prompting Replacement For Aesthetic Reasons.

Practical Tips

• Inspect The Hinge And Retaining Spring When Replacing The Cover; Replace Any Worn Clips To Avoid Repeat Failures.
• Clean The Filler Neck Area Before Fitting The New Cover To Ensure Proper Seating And To Prevent Abrasion.
• If Color Matching Is Critical, Confirm The Paint Code KGN (LAK BOURRASQUE) Against The Vehicle’s Records.

Packaging And Stock

Part Supplied Painted In KGN – Other Colors Available From Stock. Check The Listed Product Codes When Ordering To Ensure Correct Color And Variant.

This painted fuel filler flap is an exact-fit exterior body part designed for the Peugeot 308. It restores the original appearance around the fuel filler, protects the filler neck from dirt and moisture, and houses the hinge and latch elements that keep the flap closed. Supplied in high-gloss Black Pearl Nera finish (KTV paint), the part is ideal for body repair, replacement after minor collisions, or cosmetic refurbishment. Commonly searched by OEM numbers, this item is suitable for professional garages and experienced DIYers who require a straight, painted replacement part that matches the vehicle exterior.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 308
• Product Codes: 1517G5; 9681632777
• Additional Numbers: Not specified

Fitment

Intended for Peugeot 308 models. Verify the part numbers 1517G5 or 9681632777 against the vehicle’s existing part to confirm visual and mounting match. The painted finish is matched to KTV Black Pearl Nera; other colors are available on request.

Installation

Replacement of the filler flap is generally straightforward for a trained mechanic or capable DIYer. Typical steps:

• Open the filler flap and remove any visible screws or clips securing the inner trim or splash guard.
• Access the hinge and latch assembly from inside the wheel arch or filler recess; remove retaining fasteners or gently release hinge pins.
• Transfer any hinge components, seals or locking actuator (if applicable) to the new flap, or fit the supplied hinge hardware and align the flap on the vehicle.
• Adjust alignment so the gap to the surrounding bodywork is even and the latch engages smoothly; tighten fasteners to manufacturer torque where specified.
• Check operation by opening/closing several times and inspect the paint for contact blemishes.

Estimated workshop time: 15–45 minutes depending on access and whether inner liners must be removed. Required tools: trim tools, screwdriver or Torx set, socket set, and possibly a small pry tool for hinge pins.

Installation Recommendations

• Keep all original fasteners where possible; replace any corroded clips or screws to ensure secure mounting.
• If the part includes a lock actuator or electrical connector, verify connector condition and routing before final assembly.
• Protect the painted surface during installation to avoid scratches—use soft cloths or masking where required.
• Align the flap before fully tightening fasteners to prevent stress on hinge points and ensure a flush fit with surrounding panels.

Most Common Failure Causes

Fuel filler flaps most often require replacement due to external damage (parking impacts, minor collisions, vandalism) or hinge/latch wear. Corrosion can affect mounting points on older vehicles, and painted flaps are prone to scratches and chipping from road debris. Problems with the locking actuator or seized hinge pins can prevent proper closure, creating the need for a full flap replacement rather than individual hinge repair.

Why Choose This Part

Buying a painted, ready-to-fit filler flap saves time on painting and refinishing, delivering a factory‑match look when the color code is correct. The presence of OEM product codes (1517G5 / 9681632777) makes it easy for mechanics to locate the correct replacement and ensure an accurate fit for Peugeot 308 applications.

Note

This description references the manufacturer part numbers shown above. Always inspect the existing part and mounting points prior to installation to confirm fitment and any additional components required for a complete repair.

Premium replacement fuel filler cap cover designed specifically for Citroën C4 Grand Picasso owners and professional technicians. This painted exterior flap restores the vehicle’s original appearance and protects the filler neck from dirt, moisture and road debris. Many buyers search by part number (9654052080, 1517E4, 1517E3), so this listing is optimized to match common queries by mechanics and DIY enthusiasts looking for a direct-fit, color-matched panel in KGQ (Kyanos Blue).

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 Grand Picasso
• Product Codes: 9654052080, 1517E4
• Additional Numbers: 1517E3, 1517000, 15170000

Fitment And Compatibility

Intended for Citroën C4 Grand Picasso models that require the above part numbers and painted in KGQ (Kyanos Blue). Always verify the part number stamped on the original filler cover before installation. This is the exterior flap only; it fits in place of the original body panel and interfaces with the factory hinge and latch assembly.

Function

The fuel filler cap cover protects the filler neck and cap from environmental contamination and mechanical damage while maintaining the vehicle’s exterior appearance. It forms the visible outer part of the fuel filler assembly and ensures proper sealing and alignment with the surrounding bodywork. On some trim levels the fuel flap operation is integrated with the vehicle’s central locking system; this listing refers to the external cover/panel itself.

Installation Recommendations

• Prepare Tools: small ratchet, Torx/Phillips bits or screws as used on the vehicle, trim clip tools, and a torque driver if specified by the repair manual.
• Removal: Open the filler flap and remove hinge fasteners or clips. On some model years access to the hinge fasteners may be easier from the inner wheel arch or trunk side by removing the liner.
• Fitment: Align the new cover with the hinge and latch points, tighten fasteners evenly and check for correct gap and flush fit with surrounding body panels.
• Adjustment: If alignment is off, loosen hinge fasteners slightly, adjust position and retighten to the correct torque. Ensure the latch releases and closes smoothly without binding.
• Finish: Inspect paint finish for any transport scuffs before installation. If repainting or touch-up is required, follow manufacturer paint-preparation procedures to avoid mismatch.

Replacement Frequency & Maintenance

Fuel filler flaps do not have a fixed service interval. Replacement is normally required after impact damage, corrosion of hinge/latch components, or progressive paint deterioration. Regular cleaning of the hinge and latch area and occasional lubrication of moving points will extend service life.

Why The Part Most Often Fails

Common causes of failure include stone chips or minor collisions that break the hinge or deform the flap, corrosion of hinge pins and fasteners from road salt and moisture, loss of paint adhesion from UV exposure, or vandalism. Latch failure can result from debris ingress or corrosion preventing proper engagement.

Notes For Professionals And DIYers

This part is suitable for bodyshops and independent mechanics needing a direct-fit, color-matched replacement. Because many customers search by OE number, listing the correct codes (9654052080, 1517E4, 1517E3) speeds up finding the right item. When replacing the flap, check hinge hardware and latch condition and replace corroded fasteners to ensure a durable repair.

This used fuel flap cover is a direct-fit replacement for the first‑generation Peugeot 3008. Designed to restore the appearance and function of the vehicle’s fuel filler area, the panel is finished in EPY (Rubi Red) paint and is commonly sought by part numbers such as 9682803080 and 1517G9. Ideal for professional workshops and DIY mechanics, this part helps avoid costly bodywork and keeps the filler neck protected from dirt and moisture.

Function And Benefits

The fuel flap cover (fuel filler flap) protects the fuel filler neck from road dirt, water ingress and minor impacts. Besides the protective role, it completes the exterior styling of the vehicle and may incorporate the latch that secures the flap. Replacing a damaged flap restores proper sealing and prevents contamination of the filler area.

Compatibility And Fitment

Fits: Peugeot 3008 First Generation (3008 I). The part is often searched by OE numbers—use the codes in the Technical Information section below when searching or ordering. Painted in EPY Rubi Red; other colors available from stock.

Installation Recommendations

• Recommended For: Experienced Automechanics And Competent DIYers.
• Tools: Plastic trim tools, Torx/screwdrivers for hinge screws, small ratchet set, panel clips pliers.
• Procedure Overview: Open the fuel flap and access the mounting fasteners (may require removing inner trunk trim or wheel-arch liner depending on model). Remove retaining screws or clips, carefully detach the hinge and any rubber surround or spring, and replace the cover. Transfer any spring/hinge parts from the old unit if required. Align the flap, secure fasteners to manufacturer torque where available, and verify smooth opening/closing and sealing.
• Tips: Protect painted edges during installation to avoid scratches. Replace broken clips and worn hinges to ensure correct alignment. Do not overtighten plastic screws to prevent cracking.

Why This Part Commonly Fails

• Impact Damage: Minor parking impacts, fuel-pump collisions or dooring incidents often crack or deform the flap.
• Worn Hinges And Clips: Plastic hinges and retaining clips become brittle with age and can break from repeated use or cold exposure.
• Corrosion And Debris: Accumulated dirt, salt and moisture can lead to latch sticking or accelerated wear of fastening points.
• Paint Damage: Scratches and chips from refuelling or road debris lead owners to replace the flap for cosmetic reasons.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 3008 I (First Generation)
• Product Codes: 9682803080, 1517G9
• Additional Numbers: 151800, 1518E2 (Filler Neck Housing)

Note: This item is sold as a used replacement part. Colour matching may vary slightly depending on paint aging. We also stock the filler neck housing under code 1518E2 and additional colors for the flap cover.

Product Overview

This is a direct-fit fuel filler cap and outer cover assembly intended for Peugeot 407 Sedan. The part includes the filler neck housing, providing a neat, ready-to-install replacement for damaged or corroded fuel flap areas. Finished in KKQ (Red Profond) paint, it helps restore the exterior appearance while maintaining correct alignment with the body lines.

Key Features

• Complete assembly: Fuel filler cap/cover plus filler neck housing included.
• Color matched to KKQ (Red Profond) for a factory look.
• Direct replacement for Peugeot 407 Sedan — fast and straightforward installation for technicians and DIYers.
• Durable plastic construction with integrated mounting points and sealing interfaces.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 407 Sedan
• Product Codes: 1517A6, 151877
• Other Numbers: Color Code KKQ (Red Profond)

Intended Applications

Designed for use on Peugeot 407 Sedan models that require a replacement fuel filler cap/cover in KKQ Red Profond. Suitable for body repair shops, service garages and experienced DIY mechanics replacing a damaged fuel flap assembly.

Installation Recommendations

Recommended Steps: Remove the old fuel flap assembly by opening the filler door, removing the visible screws or plastic retainers, and releasing the hinge clips. Disconnect any retaining springs or the filler cap lock mechanism if present. Install the new assembly by aligning mounting points, snapping hinge clips into place and securing with the original or OEM-equivalent fasteners. Check the filler cap seal for proper compression and ensure the door closes flush with the surrounding body panel. Avoid overtightening fasteners to prevent cracking the plastic. If paint touch-up is required, mask surrounding panels to protect finish.

Common Failure Causes

Fuel filler covers typically fail due to external impact (minor collisions or parking scrapes), broken hinge pins or plastic clips, corrosion where metal components contact road salt, and wear of seals or latches from repeated use. Paint damage and fading are common on exposed flaps, especially on older vehicles. Replacement is usually required after physical damage or when the door no longer closes or seals correctly.

Practical Tips For Fitment

• Verify color code KKQ against the vehicle’s paint code to ensure a close match.
• Retain original fasteners where possible; replace damaged clips to ensure secure mounting.
• Inspect the filler neck seal and locking mechanism during replacement and renew if hardened or torn.
• Perform a final check with the fuel cap installed to ensure no rubbing or misalignment that could damage the paint.

Additional Notes

This assembly includes the filler neck housing and is intended as a bodywork replacement part. Suitable for professional installation but can be fitted by experienced DIY mechanics familiar with exterior panel fastenings and trim clips.

High-quality replacement Fuel Filler Flap Cover designed for Citroën C3 II (A51) models. This unit includes the filler housing (1518E5) and is painted in KDK Hickory Brown to match original body finish. The part is commonly referenced by product codes and is frequently searched by technicians and DIYers under its OEM numbers.

Function And Application

The Fuel Filler Flap Cover protects the fuel filler neck from dirt, moisture and vandalism while maintaining the vehicle’s exterior appearance. It provides the mounting point for the filler cap and, where applicable, the lock or latch mechanism. Correct fitment ensures a flush appearance and proper sealing of the fuel door area.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C3 II (A51)
• Product Codes: 1517H3, 1518E5
• Other Numbers: 151800000
• Color: KDK – Hickory Brown (paint)
• Includes: Filler Flap Cover With Housing 1518E5

Installation Recommendations

Designed for fitment by professional mechanics and experienced DIYers. Typical replacement procedure:

• Open the filler flap and remove any visible screws or plastic clips securing the hinge and housing.
• If accessible from inside the wheel arch or trunk side, remove the inner liner to reach hidden fasteners.
• Disconnect any electrical connectors for locking mechanisms or lamp units, if present.
• Carefully release the retaining tabs and remove the old flap and housing assembly to avoid damaging the body paint.
• Position the new assembly, engage clips and fasteners, then tighten screws to the manufacturer’s torque settings.
• Reconnect electrical connectors, check alignment and operation of the latch or lock, and verify the filler cap seals correctly.

When painting or adjusting, protect surrounding panels. Replace broken clips and worn seals to ensure a long-lasting repair.

Why This Part Fails Most Often

• Impact Damage: Minor collisions or bumps at the fuel door area commonly crack the flap or break mounting tabs.
• Corrosion And Wear: Moisture ingress and road salt can corrode hinges and fasteners over time, causing sticking or detachment.
• Latch/Lock Failure: Mechanical wear or dirt in the locking mechanism can prevent proper closure or opening.
• Paint Degradation: UV exposure and stone chips lead to paint fading or chipping, prompting cosmetic replacement.
• Broken Clips/Tabs: Plastic mounting elements become brittle and fail, especially on older vehicles or after previous repairs.

Compatibility Notes

This item is intended for Citroën C3 II (A51) vehicles using the listed product codes. It is often searched under the OEM references 1517H3, 1518E5 and 151800000. Verify fitment by comparing product codes and the physical shape of the housing before installation.

Practical Tips For A Durable Repair

• Replace any broken clips or corroded screws during installation to avoid future rattles or detachment.
• Clean sealing surfaces and apply a light corrosion inhibitor on metal fasteners.
• Check the fuel cap seal and hinge lubrication while the filler area is accessible.

Direct-fit fuel filler flap tailored for Citroën C4 5-door models, finished in ETS Grey Cendré for a factory-matching look. This replacement part restores the exterior appearance and sealing of the fuel filler area, maintaining paint continuity and correct alignment with the bodywork. Frequently searched by OE numbers, this flap is suitable for professional garages and experienced DIY mechanics who expect an original-look result and reliable fitment.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C4 I (5-Door)
• Product Codes: 9650573477, 1517C1, 151880
• Additional Numbers: ETSC, ETS

How To Replace

Replacement is straightforward for a competent mechanic and requires basic hand tools. Typical procedure:

1. Open The Fuel Flap And Remove Any Visible Fasteners Or Retaining Clips.
2. Access Mounting Points From The Wheel Arch Or Inner Trim If Required And Remove Fixings.
3. Disconnect The Locking Actuator Or Retaining Cable If The Model Is Equipped With Central Locking.
4. Remove The Old Flap, Transfer Any Useful Hardware Or Gaskets, And Fit The New Flap Into Position.
5. Check Alignment, Tighten Fasteners To Manufacturer Torque Where Specified, And Test Opening, Closing, And Locking Functions.

Installation Recommendations

• Test Fit Before Painting Or Final Assembly To Ensure Correct Alignment.
• Replace Broken Clips, Gaskets, And Fasteners To Avoid Rattles Or Water Ingress.
• Lubricate Hinge Points Lightly To Prevent Squeaks And Reduce Wear.
• Verify Locking Actuator Operation After Installation If Central Locking Is Present.
• Use Primer And Paint Matching The ETS Grey Cendré Code For Visible Repairs.

Most Common Reasons For Failure

• Impact Damage From Minor Collisions Or Refuelling Incidents Leading To Cracked Or Deformed Flap.
• Plastic Hinge Or Clip Fatigue Causing The Flap To Sag Or Become Loose.
• Corrosion Around Mounting Points Or Water Ingress Affecting Fitment.
• Locking Mechanism Or Actuator Wear Resulting In Failure To Lock Or Stay Closed.
• Paint Damage From Stone Chips Or Chemical Exposure Affecting Appearance.

This fuel filler flap is an efficient way to return your Citroën C4 to original appearance and function. Supplied to match the ETS Grey Cendré finish and referenced by OE numbers for easy identification during ordering and inventory management.

High-quality replacement fuel filler cap / tank cover designed for Citroën C3 vehicles. This painted exterior part restores the original appearance after minor collisions, scratches or paint damage and is often searched by part numbers 9638184280 or 151796. Manufactured to match the KMY (Lucia Blue) factory color code, it provides a precise fit and finish for a seamless repair. Ideal for professional workshops and DIY mechanics who need a direct-fit body panel that maintains the vehicle’s aesthetics and function.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3
• Product Codes: 9638184280, 151796, KMYD
• Additional Numbers: KMY – Lucia Blue Paint

Installation Recommendations

• Prepare Tools: Panel trim tools, Torx/screwdriver set, socket set, and suitable replacement clips or screws if originals are damaged.
• Removal: Open the fuel flap, remove visible screws or rivets securing the hinge and check for hidden fasteners behind the inner trim. Carefully unclip the hinge to avoid breaking plastic tabs.
• Transfer Components: If the original lock cylinder, rubber seal or hinge hardware is intact, transfer these components to the new cap to preserve locking function and sealing.
• Fitment: Align hinge and latch points, fit the new filler cap and tighten fasteners to the manufacturer’s torque specification. Ensure the flap closes and latches smoothly without binding.
• Finish: Check paint for chips at mating edges and touch up if necessary to prevent corrosion. Replace any worn seals to maintain a proper fuel-tight closure.

Why This Part Most Often Fails

• Impact Damage: Minor collisions, parking bumps or vandalism commonly crack or deform the filler cap and hinge.
• Corrosion and Wear: Exposure to road salts and moisture can corrode hinges, fasteners and cause metal fatigue over time.
• Paint Damage: Fuel spills, stone chips and daily wear lead to paint loss; once the coating is compromised, corrosion and further deterioration accelerate.
• Broken Clips/Hinges: Plastic clips and hinge components become brittle with age and can break during repeated opening/closing.

This replacement part is a practical solution for restoring function and appearance. Searchable by part numbers 9638184280 and 151796, it is supplied in the factory-matched KMY (Lucia Blue) finish to simplify body repairs and refinishing.

High-quality replacement fuel filler cover designed for Peugeot 307 CC (Phase I and II). Ideal for professional garages and DIY enthusiasts who need an exact-fit exterior part to restore appearance and function after damage, corrosion or paint deterioration. This cover matches factory mounting points and color codes where available, making it a straightforward swap for bodywork repairs or cosmetic restoration. Common search terms: fuel filler cover, fuel flap, fuel door, Peugeot 307 CC, 9643084577, 1517A5, Babylon Red.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 307 CC I and II
• Product Codes: 9643084577, 1517A5
• Other Numbers: LKRD / LKR (color code reference), NFP (stock notation)

Function And Compatibility

The fuel filler cover protects the fuel filler neck and cap from dirt, water and minor impacts while providing a painted finish that matches the vehicle body. This unit is an exterior body part mounted on the rear quarter and is intended for Peugeot 307 CC models (convertible). Verify the paint code and product code to ensure a color match when replacing a painted cover.

How To Replace

• Open the fuel flap and remove any visible screws or retaining clips securing the inner trim or hinge.
• From inside the wheel arch or access panel, release the fasteners holding the filler cover (some models use clips, screws, or bolts).
• Disconnect any tether or illumination wiring if present, taking care not to stretch or damage the fuel cap tether.
• Fit the new cover into place, align the hinge and closing points, then secure with the original fasteners or OEM-equivalent hardware.
• Check opening/closing operation and paint alignment. If required, adjust hinge position before final tightening.

Installation Recommendations

• Use OEM specification fasteners or exact-fit replacements to maintain correct alignment and corrosion protection.
• Apply appropriate anti-seize or corrosion protection to metal fixings if the vehicle is used in salty or coastal environments.
• Lubricate hinge points with a light, weather-resistant grease to prevent squeaks and binding.
• Avoid overtightening plastic clips to prevent cracking; replace any damaged clips during installation.
• For painted covers, handle with soft gloves to avoid fingerprints and consider a final polish after installation to blend paint edges.

Why This Part Fails Most Often

Fuel filler covers commonly fail due to minor collisions or knocks (parking scrapes), rust and corrosion around fasteners or hinge points, broken plastic hinges or clips, and paint damage from fuel spillage or prolonged sun exposure causing fading and cracking. Replacing the cover is the most effective remedy when alignment or sealing is compromised.

Notes For Professionals And DIYers

Part numbers 9643084577 and 1517A5 are frequently used when searching for this item — listing these codes in your search will increase the chance of finding the correct match. This cover is suitable for bodywork repairs and cosmetic restorations on Peugeot 307 CC Phase I and II vehicles. Ensure the color code (LKR / LKRD) matches the vehicle paint to avoid visible mismatch.