Used exterior trim piece designed for the Citroën C3 II (A51). This left‑side protective strip with chrome detail restores the original appearance of the area above the front fender and mirror base. Ideal for professional workshops and skilled DIYers looking for a direct-fit replacement part numbered 9025V8. The part preserves the vehicle’s styling while protecting the bodywork edge from minor impacts and abrasion.

Compatibility

Designed For Citroën C3 II (A51). Often Searched By Part Number: 9025V8.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C3 II (A51)
• Product Codes: 9025V8
• Other Numbers: None Available

Function And Benefits

The trim protects the upper edge of the front wing and the mirror mounting area from stone chips, scratches and minor impacts. The chrome finish restores the original visual accent and contributes to a factory-correct appearance. As an exterior trim component, it does not affect vehicle mechanics but plays an important role in preventing further paint damage and corrosion around the mirror/fender joint.

How It Is Replaced

Replacement Is Straightforward For Experienced Technicians: remove the mirror glass or release the mirror cover where necessary to access retaining clips; carefully pry out the old trim with plastic trim tools to avoid damaging paint; inspect and replace any broken clips or retainers; clean the mounting surfaces of dirt and adhesive residues; press the new trim into place until all clips engage. Refit mirror components and verify fitment and gap alignment.

Installation Recommendations

• Use Plastic Trim Tools To Avoid Paint Damage.
• Replace Any Broken Clips Or Retainers To Ensure Secure Fitment.
• If The Assembly Incorporates Electrical Elements (Indicators/Heating), Isolate The Circuit Or Disconnect The Battery Before Work.
• Work On A Clean, Dry Surface And Check Panel Gaps After Installation.
• Lubricate Clips Lightly With Plastic-Safe Grease If Necessary For Easier Installation.

Why This Part Most Often Fails

Exterior Mirror And Fender Trims Fail Primarily From Impact Damage (Parking Scrapes, Side Swipes Or Road Debris). Secondary Causes Include Weathering And UV Exposure Leading To Chrome Peeling Or Surface Fade, And Mechanical Damage To Retaining Clips During Previous Repairs. Because Clips And Tabs Are Plastic, They Are Prone To Breakage When Panels Are Removed Improperly.

Notes For Buyers

Part Number 9025V8 Is Frequently Used To Locate This Item In Catalogs And Search Engines. Suitable For Professional Fitters And Knowledgeable DIY Enthusiasts. Inspect Mounting Clips And Adjacent Bodywork When Replacing To Avoid Recurring Fitment Issues.

This genuine-style protective trim (part number 9025V9) is designed for the passenger-side exterior area on Citroën C3 II (A51) vehicles. The piece combines a protective function with a chrome-accented finish to restore the original appearance and protect the bodywork around the right mirror/fender area. Ideal for professional workshops and experienced DIY enthusiasts, this replacement helps maintain the vehicle’s factory look and prevents further damage to the underlying panels.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 II (A51)
• Product Codes: 9025V9
• Additional Numbers: Passenger Side / Right

Function And Fitment

The Trim Protects The Outer Edge Above The Right Fender/Mirror Area From Stone Chips, Scratches And Weathering While Providing A Chrome Detail That Matches Factory Trim. It Sits Over The Outer Body Flange And Secures With Clips Or Tabs To The Door/Mirror Housing. Correct Fitment Restores Aerodynamics And Visual Continuity Between Mirror And Bodywork.

How To Replace

• Prepare The Vehicle: Park On A Level Surface And Protect The Paint With Soft Towels Or Masking Tape Around The Work Area.
• Access The Mounting Points: Depending On Design, Remove The Mirror Glass Or Open The Mirror Housing To Reach Retaining Clips—Use A Plastic Trim Tool To Avoid Damage.
• Remove The Old Trim: Gently Pry Off The Old Trim By Releasing Clips Or Screws. Keep Broken Clips For Replacement If Necessary.
• Fit The New Trim: Align Tabs And Clips, Press Evenly Until The Trim Clicks Into Place. Ensure All Clips Engage And The Chrome Edge Sits Flush With The Body.
• Final Check: Verify Mirror Operation And That No Seal Or Cable Is Pinched. Clean The Area To Remove Fingerprints Or Residue.

Installation Recommendations

Use Dedicated Plastic Trim Tools To Avoid Scratching Paint Or Breaking Clips. Inspect All Retaining Clips And Replace Any Damaged Fasteners To Ensure Long-Term Retention. If The Mirror Glass Must Be Removed, Handle It Carefully And Keep It Supported To Prevent Dropping. For Best Results, Fit The Trim At Moderate Temperatures To Improve Flexibility Of Plastic Clips.

Most Common Failure Causes

• Impact Damage From Road Debris Or Minor Collisions Causing Cracks Or Broken Clips.
• Plastic Fatigue And Clip Breakage Due To Age, Repeated Removal, Or Temperature Cycling.
• Surface Wear And Fading From UV Exposure, Leading To Discoloration Of The Painted/Coated Finish.
• Improper Previous Repairs Or Incorrect Reinstallation Causing Poor Fitment And Rattles.

This part Is Frequently Searched By Its Product Code 9025V9—Include The Code When Searching For Fast, Accurate Replacement Options. Suitable For Professionals And Confident DIYers Who Want A Reliable Visual And Protective Repair For The Passenger-Side Mirror/Fender Area.