Upgrade or replace your damaged right side mirror with a direct-fit unit designed for Peugeot 307 models. This electrically adjustable mirror includes an integrated temperature sensor with a 6-pin connector and comes finished in ETS Cendre Gray paint. Ideal for professional mechanics and DIY enthusiasts, the unit restores full mirror adjustment and sensor functionality without the need for additional parts. Minor paint blemishes may be present, but the mirror is structurally intact and fully operational.

Technical Information

Manufacturer: Stellantis / Peugeot
Model: Peugeot 307 (307 I) — Passenger Door Right
Product Codes: 8149A, 8149AX, 8149AX ETSC
Other Numbers: ETSC

Key Features

• Electrically adjustable mirror motor for precise positioning.
• Integrated temperature sensor (6-pin connector) for climate and mirror-heating functions.
• Painted Finish: ETS Cendre Gray — ready to fit without additional painting for matching interiors/exteriors.
• Direct fit for Passenger Door (Right Side) on Peugeot 307 models.

Installation Recommendation

Disconnect the vehicle battery before starting work to prevent electrical shorts. Typical replacement steps:

1. Remove the interior mirror trim or triangular door cover to access mounting fasteners.
2. Unscrew the mirror mounting bolts while supporting the mirror from the outside.
3. Carefully unplug the 6-pin electrical connector for the motor and temperature sensor.
4. Fit the new mirror, connect the 6-pin connector, and loosely install mounting bolts.
5. Reconnect the battery, test mirror adjustment, heating and sensor signals, then tighten mounting bolts to manufacturer torque and reassemble the trim.

Why This Part Fails Most Often

• Impact Damage: Collisions or knocks from curbs and doors are the most common causes of physical failure.
• Water Ingress and Corrosion: Moisture can corrode connectors or motor terminals, causing intermittent or permanent electrical failure.
• Motor Wear: Repeated use and age can wear the adjustment motor, reducing responsiveness or causing failure.
• Sensor Faults: Temperature sensors or wiring can fail due to corrosion or wiring fatigue.

Practical Notes

This mirror is suitable for mechanics and experienced DIYers who are comfortable removing door trim and working with electrical connectors. Verify connector type and mirror mounting pattern visually before installation. After installation, always confirm full functionality of electric adjustment and sensor outputs prior to final reassembly.

Order this right exterior mirror for Peugeot 307 to restore safe visibility and full mirror functionality — a cost-effective replacement that gets your vehicle back on the road quickly.

This replacement left mirror is designed for mechanics and experienced DIYers who need a reliable, direct-fit solution for Peugeot 307 vehicles. The unit combines electric adjustment, heating element and power-folding for convenient operation and improved safety in cold or wet conditions. It is commonly referenced under product code 8149VV and is available in different finishes — please check the color code (LKR) to match your vehicle’s paint.

Key Features

• Driver’s Side (Left) Exterior Mirror for Peugeot 307
• Electric Adjustment for precise mirror positioning
• Integrated Heating Element to clear ice and fog
• Electric Folding Mechanism for parking protection
• Painted Finish: LKR – Babylone Red
• Connector: 7‑pin (5+2)
• Typical Professional or DIY Replacement Part Number: 8149VV

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model(s): Peugeot 307 (including 307 I)
• Product Codes: 8149VV
• Other Numbers: 7 PIN (5+2); Color Code: LKR (Babylone Red)

Installation Recommendations

• Before starting, disconnect the negative battery terminal to avoid short circuits and unintended airbag deployment.
• Remove the interior door trim or triangular mirror cover following the vehicle manufacturer’s procedure to access the mirror mounting bolts and connector.
• Carefully unplug the 7‑pin connector and compare pins to ensure full correspondence (5+2 configuration).
• Support the mirror during removal to prevent damage to the glass or paint. Remove mounting nuts, fit the new mirror, and torque fasteners to manufacturer specifications if available.
• Reconnect the electrical connector, reconnect the battery and test all functions (adjustment, heating and folding) before refitting the door trim.
• Check mirror alignment and ensure the painted finish matches surrounding panels. Replace any damaged clips or fasteners removed during disassembly.

How The Part Is Replaced

Typical replacement involves removing the interior trim piece near the mirror, disconnecting the electrical connector, unbolting the mirror from the door, and fitting the new unit in reverse order. After connection, verify mirror adjustment, heater activation and folding operation. Reassemble the door trim once correct operation is confirmed.

Why This Part Fails Most Often

• Mechanical Damage: Impact or collisions commonly crack the mirror housing or glass.
• Water Ingress And Corrosion: Moisture can corrode connectors, wiring and the small electric motors, causing failures in adjustment, heating or folding functions.
• Wear Of Internal Actuators/Gears: Repeated use can wear the plastic gears inside the folding mechanism or the adjustment motor.
• Connector Or Wiring Faults: Broken pins, loose terminals or damaged wiring in the door harness lead to intermittent or total loss of function.
• Electrical Supply Issues: Blown fuses, faulty switches or relays can appear as mirror failures but originate elsewhere in the vehicle’s electrical system.

Notes For Professionals

When replacing, ensure connector pinout and available functions (heated, folding, memory if applicable) match the vehicle specification. Test all features before completing the job to avoid return visits. For painting or color-matched units, confirm the LKR color code corresponds to the vehicle’s paint.

Keywords: Left mirror, Driver side mirror, Peugeot 307 mirror, Electric folding mirror, Heated mirror, 8149VV.

This replacement right passenger mirror is designed for professional workshops and DIY mechanics who demand reliable fitment and full functionality. It restores electric adjustment, heating and power folding functions while matching the vehicle colour LKR (Red Babylone). The part number 8149VT is commonly used when searching for compatible units.

Features

• Electric Adjustment For Precise Mirror Positioning
• Heated Glass To Reduce Fogging And Ice Build-Up
• Electric Folding Mechanism For Parking And Narrow Spaces
• Integrated Temperature Sensor For Climate-Related Functions
• Colour Matched To LKR – Paint Red Babylone
• 8 Pin Connector Configuration (6+2)

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 307 (307 I)
• Product Codes: 8149VT, LKRD
• Additional Numbers: Connector 8 Pin (6+2); Colour Code LKR (Red Babylone)

Compatibility And Application

Suitable For Front Right Passenger Side Of Peugeot 307 Models Where The Vehicle Uses An 8-Pin Mirror Connector And Colour Code LKR. Often Searched Under Part Number 8149VT.

Installation Recommendations

• Disconnect The Battery Before Starting Work To Avoid Short Circuits And Airbag System Issues.
• Remove Interior Door Panel To Access Mirror Fasteners And Wiring Harness.
• Carefully Disconnect The 8-Pin Connector And Any Additional Plugs (Heater/Temperature Sensor).
• Unscrew Mirror Mounting Bolts, Replace Unit, And Refit Bolts To Manufacturer Torque Settings.
• Reconnect Wiring And Test All Functions (Adjustment, Heating, Folding, Sensor Signals) Before Reassembling Door Trim.
• Follow Manufacturer Procedures To Avoid Damage To Clips, Wiring, Or Door Trim.

Most Common Reasons For Failure

• Water Ingress Causing Corrosion Of Connectors And Electric Motors.
• Wear Of Adjustment Motors Or Gearsets After Years Of Use.
• Mechanical Damage From Impacts Or Folding-Related Stress.
• Faulty Heating Element Or Broken Wiring To The Heated Glass.
• Damage To Folding Mechanism Due To Obstructions Or Ice.

Replacing A Faulty Mirror Restores Safety And Convenience — Clear Rearward Vision And Reliable Operation Are Essential For Everyday Driving. Order By Part Number 8149VT To Ensure Fast Identification And Compatibility.

This left (driver side) exterior mirror is designed for the Peugeot 307 and is commonly searched under the part code 8149AW and color code EZAC. Ideal for professional workshops and competent DIYers, the unit offers direct replacement with an electrical 5-pin connector for mirror adjustment. The neutral grey finish (EZAC) ensures a factory-look match on vehicles finished in the same paint code.

Features And Benefits

Plug-and-play replacement for a precise fit and correct function on compatible Peugeot 307 models. Electrically adjustable mechanism allows quick calibration from the driver’s seat. Robust housing and OE-style mounting points simplify installation and reduce alignment work. Frequently sought after under part number 8149AW, making it easy to find the correct unit when ordering.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 307
• Product Codes: 8149AW
• Additional Numbers: EZAC (Color Code)

Installation Recommendations

Remove the interior triangular trim or small door panel cover to access the mirror mounting nuts. Disconnect the 5-pin electrical connector before removing the mounting bolts. Install the new mirror, connect the electrical plug, lightly tighten mounting nuts, then test all mirror functions (adjustment, folding if applicable) before fully torquing the fasteners. Use non-marring trim tools to avoid damaging interior panels and ensure the door seals are correctly positioned after reassembly. Verify mirror alignment and operation on both low and high settings, and check for any wind noise after installation.

Common Causes Of Failure

Exterior mirrors most often fail due to direct impact or collision damage (parking knocks, side swipes). Electrical faults such as connector corrosion or wiring damage can prevent the adjustment motor from operating. Internal motor or gear wear over many years may cause sluggish or no movement. Freezing and subsequent forced manual adjustment can also damage the mechanism or housing.

Practical Notes

There is no fixed replacement interval; longevity depends on usage and exposure. For correct compatibility, ensure the vehicle uses a 5-pin electrical mirror and that the color code EZAC (Grey Sidobre) matches your vehicle’s finish if cosmetic match is important. Searching by part number 8149AW will speed up locating the exact replacement unit.

High-quality interior rearview mirror designed for direct replacement on Citroën and Peugeot vehicles. This mirror, commonly searched under part number 8149NA, restores clear rear visibility and maintains the original interior appearance. It is suitable for professional workshops and skilled DIY enthusiasts who perform routine interior replacements. The mirror comes in color code FBJ – LAMA to match original upholstery and trim finishes.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C2, Citroën C3, Citroën C4, Peugeot 307, Peugeot 1007
• Product Codes: 8149NA
• Additional Numbers: Color Code FBJ – LAMA

Function And Description

The interior rearview mirror provides the driver with a clear central view of the traffic behind the vehicle. Depending on vehicle equipment, the mirror may be a simple manual unit or include integrated features such as auto-dimming, ambient lighting, or housing for sensors. This listed unit is supplied to match original mounting points and interior color.

Replacement Procedure

• Prepare The Vehicle: Park on a level surface and engage the parking brake. If The Mirror Has Electrical Connections (e.g., Auto-Dim Or Lighting), Disconnect The Battery Before Starting.
• Remove Trim: Carefully remove any overhead trim or plastic cover hiding the mirror mount to avoid damaging clips.
• Release Mirror From Mount: Depending On Mount Type, Slide The Mirror Off The Bracket Or Unscrew Fasteners. For Windshield-Mounted Mirrors With Adhesive Pads, Carefully Follow The Manufacturer Procedure To Remove The Adhesive Pad Without Damaging The Glass.
• Install New Mirror: Position The New Mirror On The Mount, Reconnect Any Electrical Connectors, And Secure Clips Or Screws Firmly. Replace Trim And Reconnect The Battery If Disconnected.
• Functional Check: Verify Mirror Position, Stability And Any Electrical Functions (Auto-Dim, Lights) Before Completing The Job.

Installation Recommendations

• Use Appropriate Tools: Plastic trim tools protect interior panels and clips during removal.
• Follow Manufacturer Procedures: For Windshield Adhesive Mounts Use Approved Adhesive Kits If The Mounting Pad Is Replaced.
• Handle Electrical Connectors With Care: Ensure Connectors Are Clean And Fully Engaged; Reconnect The Battery Only After All Connections Are Secure.
• Check Alignment: Adjust Mirror Position For Optimal Rear Visibility And Ensure Mounting Is Rigid To Prevent Vibration.

Why This Part Fails Most Often

• Impact Damage: Road Debris Or Minor Collisions Can Crack The Glass Or Break The Mount.
• Mounting Failure: Plastic Clips Or Adhesive Pads Can Degrade Over Time, Causing The Mirror To Loosen Or Fall Off.
• Moisture Ingress: For Mirrors With Electrical Components, Water Penetration Can Cause Malfunctions Or Short Circuits.
• Wear And Tear: Frequent Adjustments And Vibrations Can Cause Internal Mechanisms To Loosen, Leading To Unstable Mirror Position.

Often searched by part number 8149NA. Order this direct-fit interior mirror to restore factory appearance and safe rear visibility.

Overview

High-quality left (driver) exterior mirror designed for Peugeot 307 vehicles. This unit provides electric adjustment, integrated heating for rapid de-icing/defogging, and an electric folding mechanism for improved protection in tight parking situations. The mirror is supplied in color code KKN (Aden Red) and features a 7-pin (5+2) electrical connector. Commonly searched under product code 8149VV and reference KKNB.

Key Benefits

• Direct fit for matching Peugeot 307 models (see Technical Information).
• Electric heating speeds up demisting in cold or wet conditions.
• Electric folding reduces risk of damage when parking and improves clearance in narrow spaces.
• 7-pin connector preserves original wiring for fast replacement without splicing.
• Color-matched finish (KKN Aden Red) for a factory appearance.

How It Works

The mirror houses an electric actuator for mirror glass adjustment, a resistive heating element behind the glass to clear frost and condensation, and an electric folding motor assembly. Signals travel through the 7-pin connector (5 pins for adjustment/heater and 2 pins typically for folding or additional functions depending on vehicle wiring) to operate each function from the cabin controls.

Replacement Procedure

Recommended for experienced technicians or competent DIY mechanics. Typical replacement steps:

• Disconnect the vehicle battery to avoid short circuits and protect vehicle electronics.
• Remove the interior door trim or triangular cover to access mirror fasteners and electrical connector.
• Disconnect the 7-pin electrical connector and remove mounting nuts/bolts securing the mirror to the door.
• Remove the old mirror, fit the new unit in position and secure fasteners to the manufacturer’s torque specification.
• Reconnect the electrical connector and reconnect the battery.
• Verify full functionality: mirror adjustment, heating operation, and folding mechanism. Check for correct fit and panel alignment.

Installation Recommendations

Always follow manufacturer safety procedures. Use proper trim tools to avoid breaking door clips and take care around side airbag modules—if the vehicle is equipped with airbags, consult vehicle service literature before removing trim. Ensure connector pins are clean and undamaged; apply contact cleaner if necessary. After installation, test all mirror functions and check for noise or binding in the folding mechanism. If bodywork was repainted, verify color match (KKN Aden Red) before final assembly.

Why This Part Fails Most Often

• Impact Damage: Collisions or knocks while parking are the most frequent cause of mirror failure (broken housing, cracked glass, bent actuator).
• Water Ingress and Corrosion: Moisture can corrode electrical contacts or short motors/heaters, causing intermittent or permanent failure.
• Wear Of Folding Mechanism: Repeated folding/unfolding and mechanical stress can wear gears or motor brushes over time.
• Connector Issues: Pin corrosion or damaged wiring at the 7-pin connector can disable one or more functions.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 307 (First Generation / 307 I)
• Product Codes: 8149VV, KKNB
• Other Numbers: Connector 7-pin (5+2); Color Code KKN (Aden Red)

Compatibility Notes

Designed primarily for Peugeot 307 (307 I) models. Confirm that the 7-pin connector and folding function match the original unit on the vehicle before installation. The product code 8149VV and reference KKNB are commonly used in searches for this mirror.

Final Advice

If replacing after an impact, inspect the door mounting area and wiring harness for hidden damage. For a neat cosmetic result, verify paint code KKN (Aden Red) and consider professional painting if exact color matching is required. After fitting, perform a full functional check and adjust mirror position as needed.

Part description

Right electric rearview mirror for Peugeot 307 with heating function, electric folding and integrated temperature sensor. The part is in the color KKN – Aden red lacquer and is intended for the passenger side. Thanks to the 8 PIN (6+2) connector, it is suitable for designs with the same cabling and equipment.

If you are looking for a part by number, the key designation is 8149VT (also color code KKNB). Ideal choice for quick replacement after mirror damage or non-functioning heating/folding.

Technical information

• Manufacturer: Stellantis Citroën Peugeot
• Model: Peugeot 307
• Other numbers: KKNB
• Side: right (passenger)
• Control: electric
• Functions: heating, electric folding, temperature sensor
• Color: KKN – Aden red lacquer
• Connector: 8 PIN (6+2)

Product codes

• Product codes: 8149VT, KKNB

Installation recommendations

Generally/typically for rearview mirror replacement the procedure below applies. The exact steps may vary depending on the specific design of the door and the equipment of the car.

1) Before assembly (checks of used part)

• Check that it is a right-hand mirror and that it has the required functions: electric control, heating, electric folding, temperature sensor.
• Compare the connector and number of pins (8 PIN / 6+2) with the old part.
• Verify condition of tilt mechanism (no excessive play), undamaged cover and glass, and undamaged wiring/grommet.
• Visually check that the attachment points are not cracked.

2) Necessary tools and materials (in general)

• Set of screwdrivers and bits (according to the type of connecting material in the door)
• Plastic pry bar for removing the upholstery (so as not to damage the plastic/upholstery)
• Ratchet/extensions (according to type of nuts/bolts)
• Contact cleaner (recommended) and cloth
• Insulating tape / cable ties to secure cabling (as needed)

3) Step-by-step assembly procedure

1. Turn off the ignition and disconnect the battery for safety reasons (especially for the electrical equipment in the doors).
2. Dismantle the inner cover at the mirror (triangular plastic at the A-pillar) and, if necessary, release a part of the door trim so that you can get to the mirror attachment.
3. Locate the mirror connector in the door and disconnect the electrical connector (do not pull the cables, but the body of the connector).
4. Loosen the mirror fasteners (nuts/bolts) and hold the outside of the mirror with your other hand to prevent it from falling.
5. Remove the old mirror and check the contact surface (dirt, gasket residues) – clean it.
6. Prepare the new mirror: check the wiring, the grommet and whether the seal fits properly.
7. Place the mirror on the door, align the position and manually screw the fastening so that the threads do not catch crookedly.
8. Tighten the fasteners evenly so that the mirror sits firmly and the gasket fits well (without overstretching).
9. Plug in the electrical connector and make sure it snaps in properly and the wiring is not pinched.
10. Refit the covers/upholstery and check that all clips fit and do not give out.
11. Connect the battery and turn on the ignition.
12. Test the functions: mirror adjustment, folding, heating (depending on the car control) and basic control of the response of the temperature sensor (if display/control is linked to it in the equipment).
• 4) Post-assembly checks and test drive/function verification
  • Check that the mirror does not vibrate while driving and is stable.
  • Verify that folding occurs smoothly and without atypical sounds.
  • After rain/washing, check that the seal fits well and does not leak into the door.

  5) The most common assembly mistakes + how to avoid them

  • Swapping the connector/pins: always compare the 8 PIN (6+2) with the old mirror.
  • Pinched wiring: guide the harness so that it is not in contact with the edges of the sheet metal and is not pinched by the upholstery.
  • Damage to upholstery clips: use a plastic pry bar and loosen gradually.
  • Incorrect seating of the gasket: clean the seating surface and align the position of the mirror before tightening.

  Reasons why the part is damaged

  • Impact/abrasion (parking, narrow passageways) – cracking of the cover, breakage of the attachment or damage to the folding mechanism.
  • Damage to electric folding – gear wear, dirt ingress or mechanical stiffness.
  • Non-functional heating – broken wires, oxidation of connectors, damaged heating elements in the glass.
  • Contacts/wiring problems – wire fatigue in door grommet, bad contact in connector.
  • Temperature sensor damage – mechanical damage or moisture in the sensor/connector area.
  ]]> https://www.usedpartsvendor.com/interior/rearview-mirror-interior/307-rearview-mirror-interior/right-mirror-peugeot-307-ktga-8149ax/ Thu, 04 Dec 2025 03:10:20 +0000 https://www.usedpartsvendor.com/uncategorized/right-mirror-peugeot-307-ktga-8149ax/ Right rearview mirror PEUGEOT 307
  Passenger side
  Electrically operated, 6 PIN
  KTG color – HURRICANE GRAY PAINT
  Can be slightly scratched paint, not cracked, fully functional

  The right rearview mirror Peugeot 307 KTGA 8149AX is an original part intended for Peugeot 307 cars of the first generation. This is the right, i.e. the passenger’s mirror, electrically controlled with a 6PIN connector. The mirror is in the color KTG – Hurricane gray paint, which was normally installed from the factory, and therefore fits well with the original paint of the car. The paintwork may be slightly scratched, but the structure is uncracked and the part is fully functional.

  Technical information:
  Manufacturer: Peugeot / PSA
  Model: Peugeot 307 (307 I)
  Side: right – passenger side
  Control: electric, 6 PIN connector
  Color: KTG – Hurricane gray lacquer
  Product codes: 8149AX, KTGA
  Other numbers: PSA CITROEN PEUGEOT 8149AX KTGA

  This part is suitable for replacing a damaged right rear view mirror, either after an accident, the mirror body breaking off or damage to the tilting mechanism. It will be especially appreciated by car mechanics and home DIYers who are looking for a cost-effective original solution without the need to reach for universal replacements that do not always fit exactly. Thanks to the exact marking with the code 8149AX and the color KTG, it is easier to find compatibility with a specific version of the car and minimize the risk of a mismatched part.

  Installation recommendations:
  – Before removing the old mirror, disconnect the battery to avoid a short circuit when handling the electrical connector.
  – Disassemble the inner plastic cover at the mirror and carefully disconnect the 6PIN connector.
  – Loosen the fixing screws of the mirror, hold the mirror from the outside so that it does not fall and damage the door paint.
  – Install the new mirror in the reverse order, making sure that the seal between the mirror and the door is properly seated to prevent water ingress.
  – After installation, connect the battery and test all directions of the electric mirror control.
  – When painting or locally repairing the paint of the mirror, use the correct shade of KTG – Hurricane gray and follow the recommended painting technology so that the appearance is as close to the original as possible.

  ]]> https://www.usedpartsvendor.com/interior/rearview-mirror-interior/307-rearview-mirror-interior/left-mirror-peugeot-307-ktga-8149aw/ Thu, 04 Dec 2025 03:10:20 +0000 https://www.usedpartsvendor.com/uncategorized/left-mirror-peugeot-307-ktga-8149aw/ Left rear view mirror PEUGEOT 307
  Driver side
  Electrically operated, 5 PIN
  KTG color – HURRICANE GRAY PAINT
  Can be slightly scratched paint, not cracked, fully functional

  The left rearview mirror for Peugeot 307 is suitable as a spare part when the original mirror on the driver’s side is damaged. This is an electrically operated mirror with a 5-pin connector, intended for cars with painted rear-view mirrors in the shade of Hurricane gray (color code KTG). Thanks to the original design, it fits the given model well and preserves the appearance and function of the car’s original equipment.

  Technical information:
  Manufacturer: PSA Peugeot Citroën
  Model: Peugeot 307 (first generation)
  Side: left – driver’s side
  Control: electric
  Number of pins: 5 PIN
  Color: KTG – Hurricane gray (painted cover)
  Product codes: 8149AW, KTGA
  Other numbers: PSA 8149.AW, color designation KTG

  The mirror is fully functional, the glass is uncracked, the mechanics and electrical controls work correctly. The paintwork may be slightly scratched, which is normal for a used part, but this does not affect function. Thanks to the exact original part number 8149AW, it is easy to find it by catalog or pre-owned parts.

  Installation recommendations:
  – Before disassembling the old mirror, disconnect the battery to avoid a short circuit when handling the wiring.
  – Disassemble the inner plastic cover at the mirror and carefully disconnect the original 5-pin connector.
  – Check that the new part has the same number of pins and connector type and that it fits the fixing points in the door.
  – Tighten the mirror evenly during installation to avoid plastic stress and vibrations while driving.
  – After installation, check the function of the electric adjustment from inside the car and, if necessary, fine-tune the position of the mirror.

  The part selected in this way is especially suitable for auto mechanics and home repairers who are looking for a cost-effective solution with an exact match of the original part according to codes 8149AW and KTGA.

  ]]> https://www.usedpartsvendor.com/interior/rearview-mirror-interior/c3-rearview-mirror-interior/interior-mirror-citroen-peugeot-8149ff-2/ Thu, 13 Nov 2025 03:02:45 +0000 https://www.usedpartsvendor.com/uncategorized/interior-mirror-citroen-peugeot-8149ff-2/ Interior rear view mirror CITROEN C2 C3 C4 and PEUGEOT 307 1007
  Color FBJ- – LAMA

  Are you looking for an original interior rearview mirror for Citroën or Peugeot with code 8149FF? We offer a used, fully functional OEM PSA part that fits perfectly and maintains the original interior appearance. This part is NFP (No Further Production) – new is no longer produced, so a quality used original is the best choice.

  Key benefits
  – Original PSA part: exact fit, no vibrations, original appearance
  – Day/night version: convenient manual switching against glare
  – Color FBJ – LAMA: light gray shade for matching interiors
  – A cost-effective and proven alternative to a new part (NFP)

  Technical information
  – OE/PSA number: 8149FF (also listed as 8149.FF, 8149 FF)
  – Design: internal rear-view mirror, mechanical day/night switching
  – Colour/interior: FBJ – LAMA (light grey)
  – Mounting: on a foot glued to the windshield (PSA standard); assembly by sliding/turning into the lock
  – Electrical equipment: without electrochrome (without automatic dimming), without connector; does not serve as a rain/light sensor holder
  – Package contents: mirror with foot mount; the glued foot is part of the windshield, not part of the part

  Compatibility
  – Citroën: C2, C3, C4 (selected versions and equipment)
  – Peugeot: 1007, 307 (I)
  Note: Different equipment may have a different design of the mirror (e.g. electrochromic). To be sure, check the match against part number 8149FF or VIN.

  Condition and origin
  – Used original PSA part, functionally tested
  – Normal cosmetic signs of use possible; the condition corresponds to the photos in the product detail

  Assembly tip
  – When removing/installing, do not handle the metal/glued foot on the glass to avoid damaging the windshield.
  – The mirror is placed on the foot and locked by clicking/turning. Assembly is a matter of minutes, without the need for electrical connections.

  Frequently searched terms (SEO)
  – interior mirror Citroën C2 C3 C4
  – interior mirror Peugeot 307 1007
  – interior/central day/night mirror
  – original mirror PSA 8149FF, 8149.FF, FBJ LAMA, NFP

  Not sure about compatibility? Email us the part number 8149FF or VIN – we’ll be happy to verify the correctness for free.

  ]]>