Original right rear light (rear lamp) for Citroën Xsara combi (break) with OE code 6351J8. The ideal replacement for a cracked, foggy or broken light – retain the original appearance and the correct geometry. This is the original removal part used, suitable for car mechanics and home repairers who need a quick and reliable solution.

The

part is designed for the right side of the car (passenger side at the steering wheel on the left). It corresponds to the original design – fits in serial handles and uses the original type of connector and sockets. Thanks to the same OE code 6351J8 you can achieve trouble -free mounting and proper function of light circuits.

Package content: rear lamp without socket and bulbs. The bolt base can be purchased in our country, which will facilitate replacement and shorten the repair time. Before mounting, we recommend checking the status of the seals and cleanliness of the bearing surfaces to avoid leaking into the lamp.

Typical reasons for replacement: mechanical damage after less collision, cracks after plastic aging, water root and subsequent corrosion of contacts, non -functional directional/brake/reverse. Inadequate rear light is a frequent reason for unsuccessful technical inspection, so timely replacement is also suitable for safety and legislation.

technical information
Manufacturer: Citroën (PSA)

Model: Citroën Xsara Estate (Break), Right side

product codes: 6351J8, 6351.J8
More Numbers: PSA NFP (No Further Production)

How to verify compatibility: The most reliable is to compare the OE number on the original episode or in the VIN catalog. If 6351J8 sits, the part is designed for your car. In case of doubt, always follow the part number, because there may be minor deviations according to the year of production or equipment.

Installation tips for replacement: Open the luggage compartment lid, remove the cap and loosen the fastening nuts/screws of the lamp, disconnect the electric connector and remove the old lamp. Transfer the bolt base (if you do not put it new), check the seals, sett down a new lamp into the body, evenly tighten the screws and test all the light functions (outline, brake, rudder, fog/reverse according to the equipment).

Original left rear light for Citroën Xsara combi (break), OEM PSA code 6350J8. It is a used part of the dismantling that fits exactly into the original handles and uses a serial connector – without modifications and without compromises in compatibility. Suitable as a substitute after damage, lighting defects or failed MOT due to poor visibility.

light performs the function of combined rear lighting (outline, brake, directional and additional functions according to the equipment). The cover is designed to ensure the correct light characteristics and readability of signals. As a result, the safety and legality of the car operation are maintained. Backets with bulbs are not included – it can be purchased separately.

The condition corresponds to age and common use, the part is suitable for immediate assembly. Compared to unoriginal substitutes, it offers accurate shape, proper fit with bodywork and long -term weather resistance.

Mounting tip: The replacement is usually easy. Open the luggage compartment, remove the inner cover/upholstery at the lamp location, disconnect the electric connector, loosen the fastening nut/screws from the inside of the body and pull the light outwards. Transfer the base with bulbs (if you use it again), check the seals, insert the new light into the body and tighten it evenly. Verify the function of all bulbs before the final assembly.

We recommend to verify compatibility according to OEM code 6350J8 and according to the design of the Kombi (Break) body. Location on the vehicle: rear left side (for left -hand drive cars).

Technical information

• manufacturer: dog/Citroën -peugeot (original part)
• Model: Citroën Xsara Estate (Break)
• Product codes: 6350J8, 6350.J8, 6350 J8
• Other numbers: Not specified

To be sure of conformity with your car, compare the shape, attachment and connector with the original part. If necessary, the code 6350J8 will help you identify the correct light.

Whether you’re a professional mechanic or a DIY car enthusiast, this lamp socket provides the reliability needed to perform safe and effective repairs. It’s important to note that while the socket is designed to house the bulbs securely, the functionality of the bulbs themselves is not guaranteed.

Replacing the rear lamp socket is a straightforward process, typically requiring only basic tools. This part plays a crucial role in ensuring visibility and safety on the road, and it’s essential to replace it if you notice any issues with your lighting system.

Technical Information

• Manufacturer: Citroën
• Model: Xsara
• Product Codes: 6351P0
• Other Numbers: Not Applicable

Compatible with Citroën Xsara models from September 2000 to April 2005, this socket serves as a reliable replacement option for worn or damaged lamp connections. The original part number is 6350P0, making it easy to find and replace as needed.

Over time, lamp sockets may fail due to exposure to moisture, heat, and frequent use, resulting in poor electrical connections or complete lamp failure. This product allows for a straightforward installation, ensuring that you can replace it with minimal tools and effort. Keep your vehicle’s lighting system in peak condition with this high-quality lamp socket.

Technical Information

• Manufacturer: Citroën
• Model: Xsara
• Product Codes: 6350P0
• Additional Numbers: Not applicable

Over time, light sockets can deteriorate due to exposure to heat, moisture, and vibrations, leading to potential lighting failures. This part is essential for both safety and compliance with traffic regulations. If you notice flickering lights or complete failure of the rear lights, it may indicate that the light socket requires replacement.

Replacing the light socket is a straightforward process. Typically, it involves removing the rear light assembly, disconnecting the old socket, and plugging in the new one. Adhering to manufacturer specifications during the installation can prevent future issues.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: Citroën Xsara
• Product Codes: 6351P0
• Additional Numbers: N/A

Product Overview

Replacement left rear lamp socket designed for Citroën Xsara Estate (Kombi). This unit accepts the vehicle’s tail, brake and indicator bulbs (bulbs not guaranteed) and is delivered with a short piece of wiring for a straightforward swap. Ideal for mechanics and DIY enthusiasts looking to restore reliable electrical contact in the rear light cluster.

Key Benefits

• Direct fit for left rear lamp assembly on Citroën Xsara Estate models where the OE socket is worn or damaged.
• Comes with a short wiring pigtail to simplify installation and avoid cutting factory harness where possible.
• Restores reliable bulb contact, reducing intermittent rear light failures and improving safety.
• Commonly referenced by part code 6350J8 / 6350.J8 for fast lookup.

Compatibility

Fits Citroën Xsara Estate (Kombi) models. Often searched and identified by product code 6350J8 (also seen as 6350.J8). Verify bulb type before installation to ensure correct lamp operation.

How To Replace

• Open the tailgate and remove the interior trim to access the rear lamp assembly.
• Unscrew the lamp cluster securing screws and gently pull the assembly out to gain access to the bulb holders.
• Unplug the original socket from the wiring harness, note the wiring positions, and remove the old socket from the lamp unit (often by twisting or unclipping).
• Install the replacement socket into the lamp cluster, connect the wiring pigtail to the vehicle harness (match colors/positions), and check mechanical fit and electrical contact.
• Refit the lamp assembly and interior trim, then test all lamp functions (tail, brake, indicator) before completing the job.
• When replacing, inspect bulbs and lamp lens for signs of water ingress or corrosion that could affect longevity.

Installation Recommendations

• Work Methodically: Keep track of screw locations and wiring positions to ensure correct reassembly.
• Clean Contacts: If present, clean corroded terminals in the lamp housing before fitting the new socket to ensure good electrical connection.
• Secure Wiring: Route and secure the pigtail to avoid chafing or pinching when reassembling the lamp and trim.
• Test After Fitment: Verify all light functions operate correctly before delivering the vehicle back to the customer or completing the job.

Why This Part Fails

Socket failures are commonly caused by plastic aging and heat cycling that lead to cracking or deformation, corrosion of electrical contacts due to moisture ingress, poor contact caused by worn bulb bases, or damage from impact or wiring strain. Vehicles exposed to road salt and high humidity are particularly prone to terminal corrosion.

Technical Information

• Manufacturer: Citroën / Stellantis
• Model: Citroën Xsara Estate (Kombi)
• Product Codes: 6350J8, 6350.J8
• Additional Numbers: None provided

Notes

Part Supplied With A Short Length Of Wiring. Bulb Functionality Not Guaranteed — Replace Bulbs If Required. Inspect The Lamp Housing For Water Ingress Or Corroded Contacts When Replacing The Socket.

This right rear lamp socket is intended for Citroën Xsara Estate (Kombi) rear light assemblies and is frequently sought under part numbers 6351J8 or 6351.J8. The socket holds the rear bulbs (tail/brake/indicator/reverse depending on vehicle lamp cluster configuration) and connects to the vehicle wiring via the supplied short piece of cable. The straightforward design makes this part suitable for professional workshops and experienced DIY mechanics who need a direct replacement socket for the rear lamp cluster.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën Xsara Estate (Kombi)
• Product Codes: 6351J8
• Additional Numbers: 6351.J8

Installation Recommendations

Follow these practical steps for a safe and reliable replacement:

• Disconnect the battery before starting work to avoid short circuits and to protect vehicle electronics.
• Open the tailgate and remove the rear light cluster retaining screws or clips (access may require folding back trim or removing luggage trim panels).
• Carefully pull the lamp assembly out enough to access the bulb holders and wiring harness.
• Unplug the main connector and release the retaining tabs or twist-lock on the socket to remove the old holder.
• Fit the new socket into the lamp assembly until it locks in place, reconnect the harness and secure the lamp cluster back to the vehicle.
• Test all relevant light functions (tail, brake, indicator, reverse) after installation. Replace any faulty bulbs as bulb functionality is not guaranteed with this part.

Common Failure Reasons

• Corrosion of contacts caused by moisture ingress into the lamp housing, leading to poor electrical contact or intermittency.
• Heat damage from overloaded bulbs or poor contact, which can melt plastic sockets or deform terminals.
• Mechanical wear or broken retaining tabs from repeated bulb changes or rough handling during lamp removal.
• Wiring fatigue at the connector, especially where the harness is bent or chafes against the bodywork.

About Replacement Frequency And Function

There is no fixed service interval for lamp sockets; replacement is normally required after signs of corrosion, intermittent lighting, visible damage to the socket or connector, or when the socket no longer secures the bulb reliably. The socket’s function is to provide secure mechanical and electrical contact between the vehicle wiring and the rear bulbs; when it fails, one or more rear light functions can stop working or behave intermittently.

Notes For Professionals And Enthusiasts

Part number searches using 6351J8 or 6351.J8 commonly yield this socket for Xsara Estate models. When replacing sockets, inspect the lamp housing for signs of water entry and replace seals or gaskets if needed to avoid repeat failures. Use appropriate bulb types and ensure correct bulb seating to prevent overheating.

Citroën XSARA is a compact family car in segment C, produced from 1997 to 2006.

The production of the Citroën XSARA took place from 1997 to 2000, with the facelift model manufactured from 2000 to 2006.

When placing an order, you can enter the VIN number, and we will check the part’s compatibility with your vehicle.

How to Replace the Third Brake Light?

We recommend having the part replaced by a professional service.

Additional codes:

6351J7 NFP

Citroën XSARA is a compact family car in segment C, manufactured from 1997 to 2006.

The production of Citroën XSARA vehicles took place from 1997 to 2000, with a facelift produced from 2000 to 2006.

When placing an order, you have the option to enter the VIN number, and we will check the compatibility of the part with your vehicle.

How to Replace the Third Brake Light?

We recommend having the part replaced by a professional service.

Additional Codes:

6350A6

Regular maintenance of your vehicle’s lighting system is crucial, as lights can wear out over time due to exposure to the elements and vibrations during driving. Symptoms of a failing light can include dimming or complete failure, which can potentially lead to road hazards. Replacing your rear light assembly not only enhances your vehicle’s appearance but also provides a critical safety function.

Replacement of the right rear light assembly is straightforward and can be performed by both professional mechanics and DIY enthusiasts. Simply remove the old assembly, disconnect the wiring harness, and install the new part by reversing the removal process. Ensure all connections are secure and test the light function before finishing the installation.

Technical Information

• Manufacturer: Citroën
• Model: Xsara
• Product Codes: 6351P0
• Additional Numbers: N/A