Premium used left front Xenon headlight assembly designed for Citroën C8 and compatible with Peugeot 807 models. This full unit includes the HID bulb and the ballast/control unit, offering a direct replacement for damaged or worn original equipment. The assembly is ideal for professional mechanics and experienced DIYers looking for a reliable, ready-to-fit headlight that restores factory-level illumination and beam pattern.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C8 (fits also Peugeot 807)
• Product Codes: 1494320080, 89006373, 620816
• Other Numbers: NFP (reference from seller listing)

Compatibility

Fits Citroën C8 and Peugeot 807 models (common production years 2002–2014). Always compare the part numbers above with your original part to ensure correct fitment.

Installation Procedure

1. Disconnect the negative battery terminal before starting work to avoid electrical damage and airbag/vehicle electronics faults.
2. Open the bonnet and, if necessary, remove the bumper or trim pieces to access the headlamp mounting points (depending on vehicle variant).
3. Unscrew the headlamp retaining bolts and carefully pull the assembly forward to access electrical connectors.
4. Disconnect the main wiring harness, the xenon ballast connector and any headlight leveling or washer connections.
5. If transferring auxiliary parts (leveling motors, washers, or brackets), remove them from the original unit and install on the replacement unit.
6. Fit the replacement unit, reconnect all connectors, and secure all fasteners to the manufacturer’s torque where specified.
7. Reconnect the battery, verify operation (ignition, headlight self-checks) and adjust headlight aim according to local regulations.

Installation Recommendation

• Wear gloves and avoid touching the xenon bulb glass surface. Finger oils shorten bulb life and can cause failure.
• Handle the ballast/control unit and its connectors with care; moisture and impact damage are common failure causes.
• After fitment, check for dashboard warning lights and clear any stored errors with diagnostic equipment if present. Proper aiming and leveling is essential for road safety and legal compliance.
• If the vehicle is equipped with adaptive lighting or automatic leveling, confirm correct operation after replacement.

Why This Part Fails Most Often

• Ballast/Control Unit Failure: The most frequent cause of xenon lighting problems—symptoms include flickering, failure to ignite, or intermittent operation.
• Bulb End-Of-Life: Xenon bulbs degrade and will eventually fail to light or produce reduced output.
• Moisture Ingress And Condensation: Leaks or cracked seals allow water into the housing, causing corrosion of connectors and electronics.
• Mechanical Damage To Mounts: Broken brackets or impact damage misalign the unit or prevent secure mounting (note: this unit is missing the lower bracket at the control unit).
• Electrical Connector Corrosion Or Wiring Damage: Poor contacts can produce intermittent faults or complete loss of function.

Notes For Professionals And DIYers

This is a used, fully functional complete Xenon headlamp assembly. The lower bracket near the control unit is missing and may require repair or bracket transfer during installation. Verify mounting points and connectors visually before installation. If you are uncertain about handling high-voltage Xenon systems or headlight leveling/adaptive functions, consult a professional technician.

Searchable reference numbers: 1494320080, 89006373, 620816. Exact item as shown in the real photos will be supplied.

This right front Xenon headlight is a direct-fit complete unit intended for Citroën C8 (also found on compatible Stellantis MPV platforms). The assembly includes the Xenon discharge bulb and the integrated control/ballast module, so it replaces a damaged or failed headlamp as a single unit. Ideal for professional workshops and experienced DIYers looking for a reliable original-equipment style replacement. Common search terms and product codes are included in the description to help you find the correct part quickly.

Technical Information

• Manufacturer: Citroën / Stellantis
• Model: Citroën C8 (compatible With Some Stellantis MPV Models)
• Product Codes: 1494319080
• Other Numbers: 89006372, 620616

Function And Notes

The Xenon headlight provides high-intensity, white light with improved road illumination compared with halogen units. The included control unit (ballast/inverter) powers the discharge bulb and manages ignition and operation. If the assembly is fully functional on delivery, it should restore correct lighting output and beam pattern when installed and aligned correctly.

Compatibility

Designed For Citroën C8. May Fit Equivalent Platforms Where The Same Headlamp Part Numbers Are Used. Verify Part Numbers Against Your Original Unit Before Installation.

Installation Recommendations

1. Disconnect The Battery Before Starting Work To Avoid Short Circuits And Protect Electronic Modules.
2. Access The Headlamp Assembly Following Manufacturer Procedures — This May Require Removing The Bumper Trim, Wheel Arch Liner Or Other Fasteners Depending On Model Year.
3. Unplug Electrical Connectors Carefully, Unscrew Mounting Bolts And Remove The Old Assembly.
4. Install The New Unit Securely, Reconnect All Plugs And Ground Points, Then Refit Any Removed Panels.
5. Check Headlight Aim And Alignment After Installation; Adjust According To Local Regulations And Manufacturer Specifications.
6. If The Unit Contains A Control Module From Another Vehicle Or Shows Error Messages After Fitment, Professional Diagnosis Or Reprogramming May Be Required.

Why This Part Commonly Fails

• Bulb Wear: Xenon bulbs Have A Finite Service Life (Typically In The Order Of Thousands Of Operating Hours) And Lose Brightness Over Time.
• Ballast/Control Unit Failure: The Inverter That Ignites And Powers The Xenon Bulb Is A Common Failure Point Due To Thermal Stress Or Internal Component Faults.
• Moisture Ingress: Damaged Seals Or Cracks In The Lens/Housing Allow Water In, Causing Corrosion, Short Circuits Or Fogging.
• Mechanical Damage: Impacts From Road Debris Or Minor Collisions Can Crack The Lens Or Misalign Mounting Points.
• Connector And Wiring Issues: Corroded Or Loose Connectors Can Lead To Intermittent Operation Or Complete Failure.

Practical Tips For Mechanics And DIY Enthusiasts

• When Replacing A Headlamp, Inspect Seals And Mounting Points; Replace Any Damaged Clips Or Gaskets To Prevent Future Moisture Problems.
• If Only The Bulb Has Failed, Replacing The Whole Assembly May Still Be Advisable If The Housing Or Ballast Shows Signs Of Age Or Corrosion.
• After Fitment, Always Verify Beam Pattern On A Flat Surface At The Recommended Distance And Adjust To Manufacturer Settings.
• Keep A Spare Xenon Bulb And Proper Protective Gloves/Tools When Working With Discharge Lamps — They Operate At High Voltage And Require Care.

Product Codes Included For Search: 1494319080, 89006372, 620616. Right Front Xenon Headlight For Citroën C8, Complete With Bulb And Control Unit.

High-quality Valeo Left Daytime Running Light (DRL) designed for the Peugeot 308. This direct-fit LED unit replaces the original equipment and restores factory appearance and daytime visibility. Ideal for professional mechanics and DIY enthusiasts who search by part number (90001685 / 6208X4). The compact LED module delivers efficient illumination, low power consumption and long service life compared with traditional bulbs, improving vehicle conspicuity during daytime driving and enhancing the front-end look of the car.

Application

Fits: Peugeot 308. Commonly referenced by product codes 90001685 and 6208X4. Suitable as a left-side (driver-side in left-hand drive vehicles) daytime running light assembly.

Technical Information

• Manufacturer: Valeo
• Model: Peugeot 308
• Product Codes: 90001685, 6208X4
• Other Numbers: Stellantis / Citroen Peugeot References

Function And Features

• Primary Function: Provide a bright, energy-efficient daytime lighting signature to increase vehicle visibility to other road users.
• Technology: LED module integrated into the front lighting cluster for consistent light output and long lifespan.
• Fitment: Designed as a direct-replacement part for the left DRL position; mounts into the existing lamp housing and connects to the original wiring harness.
• Benefits: Improved reliability over incandescent bulbs, quicker turn-on, lower current draw, and OEM style finish.

Common Failure Causes

• Moisture Ingress: Damaged seals or cracks in the housing can allow water into the unit, causing corrosion or LED failure.
• Thermal Stress: Repeated heating and cooling cycles can degrade LED modules or solder joints over time.
• Electrical Issues: Connector corrosion, wiring faults or blown fuses in the circuit can make the DRL stop working.
• Impact Damage: Front-end impacts or minor collisions often crack mounting tabs or lenses, necessitating replacement.

Replacement Guidance

Basic Steps For Replacement (General Guidance):

• Safety First: Switch off ignition and disconnect the negative battery terminal before starting work on any electrical component.
• Access: Depending on model year and bumper design, access to the DRL may require removal of the front bumper, wheel arch liner or release of retaining clips. Consult vehicle repair manual for exact procedure.
• Disconnect: Carefully unplug the electrical connector from the DRL unit. Release any retaining clips or screws holding the lamp in place.
• Replace: Remove the old unit, fit the new Valeo DRL into the mounting, secure fasteners and reconnect the wiring harness. Ensure seals are intact to prevent moisture ingress.
• Test: Before reassembling trim or bumper, reconnect the battery and verify DRL operation with ignition on. Confirm correct alignment and secure fitment.

Installation Recommendation

• Use Manufacturer Fasteners: Reuse OEM clips and screws where possible or replace damaged fasteners to ensure secure mounting.
• Check Seals And Connectors: Replace any brittle seals and clean or replace corroded connectors to avoid premature failure.
• Professional Help: If bumper removal, alignment or access requires special tools, or if there is body damage, consider professional installation to ensure correct fit and sealing.
• Post-Installation: Verify all lighting functions and check for fault codes with a diagnostic tool if vehicle indicates a lighting system warning.

Why This Part Is Searched By Code

Many mechanics and owners search by the Valeo product codes 90001685 and 6208X4 or by the vehicle model Peugeot 308 when sourcing the correct left DRL unit. Including these codes in listings ensures quick identification and helps find the exact replacement part required.

This replacement bulb socket assembly is intended for the right outer rear lamp of the Citroën C4 II (B7) second generation. Designed for professional mechanics and competent DIYers, the part restores reliable electrical contact for tail, brake and turn signal functions and is frequently searched by part number 6351KS. The unit includes the bulb holders and a short length of wiring for straightforward plug-in replacement.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C4 II (B7) Second Generation
• Product Codes: 6351KS
• Other Numbers: None Provided

Function And Benefits

The socket assembly secures the rear lamp bulbs in the right outer tail lamp cluster and provides the electrical connections for lighting circuits (tail, brake, indicator and possibly reverse depending on lamp configuration). A healthy socket ensures solid contact, correct lamp operation and minimises intermittent faults caused by loose or corroded contacts. Installing a fresh socket reduces the risk of flickering lights, poor lamp contact and heat-related failures.

Installation Recommendations

1. Safety First: Disconnect the negative battery terminal before working on the rear lighting harness to avoid short circuits.
2. Access: Open the boot and remove any trim panels or covers to reach the rear lamp cluster. Remove lamp cluster fasteners and carefully extract the lamp unit from the body aperture.
3. Disconnect: Unplug the original wiring connector from the lamp and remove the old bulb socket by releasing its retaining tabs or clips.
4. Fit New Socket: Insert the new socket into the lamp body until it clicks into place. Ensure the wiring is routed the same way as factory to avoid pinching.
5. Test: Reconnect the battery, test all lamp functions (tail, brake, indicator and reverse if applicable) before reassembling trims.
6. Reassembly: Secure the lamp cluster back into the vehicle, reinstall trim and confirm watertight seating of the lamp to prevent ingress.

Most Common Failure Reasons

• Corrosion And Water Ingress: Moisture and road salt lead to oxidised contacts and poor conductivity.
• Heat And Thermal Cycling: Repeated heating of bulbs and cooling causes plastic to become brittle and contact points to loosen.
• Vibration And Mechanical Stress: Road vibration and repeated removal/installation can break retaining tabs or damage wiring.
• Poor Contact Or Loose Connections: Worn contacts create intermittent operation, flicker or increased resistance and local heating.

Signs that this socket needs replacing include intermittent lamp operation, one lamp function not working while others do, visible corrosion at contacts or melted/deformed plastic around the socket. In everyday use, sockets often fail after many years—commonly observed on vehicles older than 8–12 years or in regions with heavy road salt or frequent moisture exposure.

This part is intended for direct replacement of the right outer rear lamp socket on compatible Citroën C4 II vehicles. Customers commonly search using the part code 6351KS when looking for this exact component.

Decorative Trim For Right Rear Taillight Designed For Citroën C4 II. This OE-fit exterior trim piece (product codes 9672155480 / 7453E4) restores the factory look of the right rear lamp assembly and is intended for workshops and experienced DIYers who want a precise cosmetic replacement. The part is commonly searched by its product number, so you will find fast identification and fitment when ordering by code.

Key Benefits

Restores Original Appearance: Matches factory styling and finish to eliminate scratches, cracks or missing trim around the right rear light. Durable Fitment: Manufactured to the same mounting points as the original, ensuring a secure and flush installation.Ideal For Body Shops And DIY Repairs: Easy to source by part number and straightforward to replace with common tools.

Installation Recommendations

Before starting, inspect the taillight clips and surrounding bodywork. Typical replacement requires access from the trunk/boot area to reach fasteners and clips. Follow these general steps:

• Open boot and remove any trim panels covering the taillight fixing points.
• Unscrew or unclip the taillight assembly fasteners (keep fasteners and clips organized for reuse if undamaged).
• Carefully withdraw the taillight to expose the decorative trim. Use a plastic trim tool to avoid scratching paint and breaking clips.
• Remove the damaged trim from the taillight or body by releasing retaining clips; replace with the new trim and press into place until clips engage.
• Reinstall the taillight assembly, secure all fasteners, and check alignment and sealing.

Recommended Tools: Trim removal tools (plastic), Phillips or Torx drivers depending on vehicle fasteners, soft gloves, and a flashlight. Typical Replacement Time: Approximately 20–45 minutes depending on skill level and access.

Why The Part Fails Most Often

• Impact Damage: Rear-end contact or minor parking collisions commonly crack or deform the trim.
• Broken Clips: Repeated removals or brittle clips (often worsened by cold or aging) cause poor retention and rattles.
• Surface Wear: Scratches, stone chips and UV exposure can dull or fade the finish, prompting cosmetic replacement.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 II
• Product Codes: 9672155480, 7453E4
• Additional Numbers: 74530000, 7453E4, 9672155480

Notes For Buyers

Search By Part Number: This item is frequently ordered using the product code—adding the code to your search speeds up identification. When removing the old trim, inspect plastic clips and replace any that are damaged to ensure a secure refit. Avoid using excessive force during installation to prevent cracking the new trim or surrounding panels.

This replacement socket assembly with bulbs is intended for the left outer rear tail light of the Citroën C4 II (second generation). Designed for both professional workshops and DIY enthusiasts, the unit provides a direct-fit solution to restore tail light function quickly. The delivered short length of wiring simplifies installation and reduces the need for additional splicing or adapters, making it a practical choice when the original holder or connector is damaged.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C4 II (Second Generation, C4 B7)
• Product Codes: 6350KS
• Other Numbers: N/A

Installation Recommendations

Replacement is straightforward for a competent mechanic or a capable DIYer. Typical steps:

1. Open the boot and remove the interior trim to access the rear lamp housing.
2. Unscrew or unclip the lamp housing from the body and pull it out enough to reach the socket.
3. Unplug the old socket from the lamp unit, cut any tape if necessary, and remove the damaged holder.
4. Fit the new socket assembly into the lamp, connect the wiring, and ensure a secure electrical connection.
5. Check the lamp seal and position the housing back into place; reattach clips or screws and reinstall trim.
6. Test all rear light functions (tail, brake, indicator, reverse if applicable) before finishing.

Recommended tools and tips: flat and Phillips screwdrivers, plastic trim removal tool, pliers, and dielectric grease for the contacts to prevent corrosion. Avoid excessive force on plastic tabs; ensure the lamp gasket is clean to maintain watertightness.

Why It Fails Most Often

• Corrosion and Water Ingress: Moisture entering the lamp or worn gaskets causes corrosion of contacts and short circuits.
• Heat and Vibration: Thermal cycling and road vibration make plastic holders brittle and can break contact points or wiring.
• Mechanical Damage: Impact to the lamp or improper removal/installation can crack the socket or damage pins.
• Electrical Overload or Poor Contact: Loose contacts or arcing from poor connections can burn the socket terminals.

Regular inspection after moisture exposure and replacing a damaged socket promptly restores reliable rear lighting and prevents further damage to the lamp harness. Use the part number 6350KS when searching to find the correct replacement quickly.

This right rear outer tail light is a direct-fit replacement for the Citroën C4 II (second generation). Ideal for professional garages and experienced DIY mechanics, the unit restores rear lighting functions and exterior appearance after collision damage, cracking or moisture ingress. The assembly is commonly searched by part numbers 9687311980 and 6351KS, so listing these codes in your search will help you find the exact match faster. Note: The lamp is supplied without the bulb holder and bulbs.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C4 II (B7) – Second Generation
• Product Codes: 9687311980
• Additional Numbers: 6351KS
• Position: Right, Outer Rear Lamp (Passenger Side on Left-Hand-Drive Vehicles)
• Supply Scope: Lamp housing only — bulb holder and bulbs not included

Installation Recommendations

Replacement is straightforward for a competent mechanic or experienced DIYer. Typical steps: open the boot and remove the inner trim to access the lamp fasteners; undo the securing screws or nuts; carefully pull the lamp assembly outward, unplug the electrical connector and remove the old unit. Fit the new lamp by reversing the procedure: connect the wiring harness, check the seal and alignment, secure fasteners to hand-tight plus a small additional turn (avoid overtightening), reinstall the trim and test all light functions (position, brake, indicator). Always disconnect the battery or ensure ignition is off when handling electrical connectors. Replace bulbs and holders separately if required and verify correct bulb types from the vehicle manual before installation.

Why This Part Fails Most Often

• Impact Damage: Rear collisions or parking knocks commonly crack the lens or damage mounting tabs.
• Moisture Ingress: Worn seals or cracked housings allow water entry, causing corrosion of sockets and connectors.
• Connector And Socket Corrosion: Oxidation of terminals or bulb holders leads to intermittent or lost function.
• Mechanical Wear: Plastic clips and mounting points can become brittle with age and break during removal or from vibration.

Choosing the correct replacement by part number (for example 9687311980 or 6351KS) ensures fitment and reduces installation time. Regular visual inspection of seals and connectors helps prevent failures caused by moisture and corrosion.

This left rear tail light assembly is a direct-fit replacement designed for Peugeot 307 SW estate models produced until 2005. It is an ideal choice for professional mechanics and DIY enthusiasts who need a reliable, OEM-style rear lamp for accident repair or to replace a worn or damaged unit. The housing and lens match original fitment, ensuring correct alignment, sealing surface and external appearance. Searchable by part code 6350Q6, this unit helps quickly identify the correct spare part when ordering or searching online.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: 307 SW (Estate) – Up To 2005
• Product Codes: 6350Q6
• Additional Numbers: NFP

Installation Recommendation

Replacement is straightforward for a trained technician or competent DIYer with basic tools. Typical steps:

• Open the tailgate and remove the interior trim panel to access the lamp mounting.
• Disconnect the electrical connector and remove any retaining screws or nuts securing the lamp.
• Carefully withdraw the old assembly from the body, noting seals and clips to avoid damage.
• Fit the new lamp, ensuring the sealing surface is clean and the unit sits flush; tighten fasteners to the correct torque.
• Install bulb holders and bulbs as required (not included), reconnect the electrical plug and check all light functions before reassembling the trim.

Most Common Failure Reasons

Rear lamps on older Peugeot 307 SW models typically fail or require replacement due to physical damage in collisions, cracked lenses from impacts or aging plastics, and water ingress caused by degraded seals which leads to corroded contacts or intermittent electrical faults. Bulb holder deterioration and brittle wiring connectors are also common on higher-mileage vehicles. Regular visual inspection of seals and connectors helps prevent moisture-related failures.

Ordering tip: Use the product code 6350Q6 when searching catalogues or parts databases to speed up finding the correct lamp for the left (driver) rear side of Peugeot 307 SW models up to 2005. Bulb holders are not included with this assembly and should be added separately if needed.

This right rear fog lamp is a practical replacement part for Peugeot 407 SW estate vehicles and is commonly searched under part numbers 9646507380 and 6351T4. Supplied as a complete assembly including the socket, it is aimed at professional mechanics and experienced DIYers who need a direct-fit unit to restore rear visibility and legal compliance in poor weather. The housing and mounting points are designed to match original equipment for straightforward installation and reliable alignment.

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 407 SW
• Product Codes: 9646507380, 6351T4
• Additional Numbers: 6351T4, 9646507380

Installation Recommendations

Install from the luggage compartment side by removing the interior trim panel to access the lamp housing. Remove the retaining screws or clips, unplug the electrical connector and withdraw the lamp assembly. Fit the new assembly into the mounting bracket, secure fasteners evenly to avoid stress on mounting tabs, reconnect the electrical plug and test the lamp function before refitting trim. Apply a small amount of dielectric grease to the connector pins to reduce the risk of future corrosion. If the bulb is not working on delivery, replace it with the correct bulb type and ensure the socket is clean and undamaged.

Common Failure Reasons

Rear fog lamps typically fail due to water ingress and corrosion of the contacts or socket, impact damage when reversing, cracked housings from road debris or minor collisions, or simply bulb burnout. Corroded connectors and damaged mounting tabs are frequent causes that necessitate replacement of the complete assembly rather than just the bulb.

Searchable by OE numbers 9646507380 and 6351T4, this unit is a convenient spare for workshops and owners maintaining Peugeot 407 SW vehicles. Replacing a damaged fog lamp restores rear visibility in adverse conditions and keeps the vehicle compliant with road safety regulations.

This left rear fog lamp is an OEM-style replacement for the Peugeot 407 SW, supplied complete with its bulb socket and wiring connector. Ideal for professional mechanics and competent DIY enthusiasts who search by part number (9646507480 / 6350T4). The unit restores rear fog lighting function and visibility in poor weather, improves safety compliance, and matches the original fit and mounting points for straightforward replacement.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 407 SW
• Product Codes: 9646507480, 6350T4
• Other Numbers: 6350T4 | 9646507480

Application

Designed specifically for the left rear fog light position on Peugeot 407 SW (estate) models. Confirm location and fitment visually against the existing unit before installation.

Installation Recommendations

• Required Tools: Flat and Phillips screwdrivers, trim removal tools, 8–10 mm socket set, gloves and a clean cloth.
• Access: On many 407 SW cars the lamp is accessible either through the trunk behind an access panel or by removing the inner bumper/trim. Work on a cold car and disconnect the battery if you will be handling electrical connectors for safety.
• Procedure: Remove the trim or access cover, unplug the wiring connector, release the retaining clips or screws securing the lamp, withdraw the assembly, and replace with the new unit. Fit the socket and bulb, secure all fasteners and trim, then test the fog lamp circuit before final reassembly.
• Sealing: Check and renew any rubber seals or gaskets if they show wear to prevent moisture ingress. Ensure connector contacts are clean and free of corrosion.
• Bulb Note: Bulb operation is not guaranteed with the supplied unit; verify bulb type and condition and replace the bulb if necessary with the correct specification from the vehicle manual.

Why It Most Commonly Fails

• Moisture Ingress: Cracked lenses or degraded seals allow water to enter, causing corrosion or electrical shorting.
• Impact Damage: Rear bumper impacts or minor collisions frequently crack the lens or break mounting tabs.
• Corroded Contacts: Exposure to water and road salts can corrode the socket contacts and wiring.
• Bulb Failure: The bulb itself can burn out independently of the housing; when replacing the assembly, check the bulb separately.
• UV And Ageing: Prolonged sun exposure and age can make the plastic lens brittle and less weatherproof.

Practical Tips

• When replacing the lamp, test the electrical circuit and grounding to avoid false faults after fitting.
• Replace damaged seals and clean connectors with electrical contact cleaner for reliable long-term operation.
• Keep the part numbers 9646507480 and 6350T4 handy when searching or ordering to ensure correct fitment and faster sourcing.