This LED third brake light (center high-mounted stop lamp) is designed for Citroën C5 I and C5 II Estate models and offers a direct-fit replacement for the factory unit. It restores the high-mounted brake signal that improves rear visibility and safety during braking. Ideal For Professional Garages And Do-It-Yourself Mechanics, The Unit Is Frequently Searched By Part Number 6350P6 — Include This Code When Looking Up Compatibility.

Features And Benefits

• Direct Replacement For Original Center High-Mounted Stop Lamp On Citroën C5 Estate Models.
• LED Technology Provides Bright, Instant Illumination And Long Service Life.
• Complete With Connector And Mounting Points For Easy Installation.
• Part Number 6350P6 For Easy Identification And Search Engine Visibility.

How It Works And Typical Failures

The Third Brake Light Serves As A High-Mounted Brake Indicator (CHMSL), Making Your Vehicle More Noticeable To Drivers Behind When Braking. Although LEDs Typically Offer Long Lifespan Compared To Incandescent Bulbs, Failures Can Occur Due To Water Ingress, Corrosion Of Connectors, Impact Damage, Or Degraded Solder Joints/Printed Circuit Board Issues. Wiring Faults Or A Faulty Brake Light Switch Can Also Result In Loss Of Function.

Replacement Guide

Basic Steps For Replacement (Approximate Time: 15–45 Minutes Depending On Experience):

1. Open Tailgate/Boot And Expose Interior Trim Around The Third Brake Light.
2. Remove Trim Fasteners Or Clips Carefully To Avoid Breakage.
3. Unscrew/Release The Lamp Assembly Fixings And Gently Pull The Unit Out.
4. Disconnect The Electrical Connector And Remove The Old Unit.
5. Fit The New Lamp, Reconnect The Connector, And Secure The Assembly In Place.
6. Reinstall Trim Panels And Test Brake Light Function With The Ignition On.

Recommendation: Verify Proper Sealing Around The Lamp To Prevent Moisture Intrusion. Clean Connector Contacts If Corrosion Is Present.

Mounting Recommendations

• Disconnect The Battery Or Ensure Ignition Is Off Before Starting Work To Avoid Short Circuits.
• Handle The Lamp With Care To Avoid Scratching The Lens Or Damaging Mounting Tabs.
• Use Correct Fasteners And Do Not Overtighten To Prevent Cracking The Housing.
• Inspect Wiring Harness And Connector For Damage; Replace Or Repair Any Corroded Contacts.
• After Installation, Confirm That The Brake Light Illuminates Correctly With The Brake Pedal Depressed.

Why This Part Fails Most Often

Common Causes Of Failure Include Water Ingress And Condensation Leading To Corrosion, Physical Damage From Impacts Or Liftgate Misuse, Deterioration Of Internal Solder Joints From Thermal Cycling, And Corroded Or Loose Electrical Connectors. Addressing The Root Cause (For Example, Damaged Seals Or Faulty Wiring) Will Help Prevent Recurrence.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C5 I Estate, Citroën C5 II Estate (Tourer/Break)
• Product Codes: 6350P6
• Additional Numbers: NFP

Notes For Professionals And Enthusiasts

When Replacing The Third Brake Light In A Workshop Setting, Check The Entire Rear Lighting Circuit If Multiple Lamps Or Indicators Are Affected. Use Appropriate Trim Tools To Avoid Damaging Interior Panels. For Vehicles With Tailgate Wiring Looms, Inspect The Loom Grommet For Tears That Could Allow Water To Enter.

This Description Is Optimized For Search Terms Such As “Citroën C5 Third Brake Light”, “C5 Center High Mounted Stop Lamp”, “6350P6 Brake Light”, And “C5 Estate Rear Brake Lamp” To Help Mechanics And DIY Customers Find The Correct Replacement Quickly.

Headlight washer covers EYLC Citroën C5 II 7414JC are a practical and at the same time aesthetic element of the front part of the car. They help protect the headlight washer mechanism from dirt and damage, while maintaining a clean and complete appearance of the bumper. Thanks to their original shape and color, they fit exactly into the design of the Citroën C5 model of the second generation.

These caps can be used both in a complete system with washer nozzles, and also separately as blanking plugs, if the washer system is dismantled or non-functional. This is suitable, for example, for vehicles after modifications, when it is necessary to aesthetically cover the original holes in the bumper. The EYL color – Iceland gray paint – matches the original factory shade, which makes it easier to match the car’s paint. In the case of a difference in paint shade, it is possible to additionally repaint the covers.

The use is suitable for Citroën C5 II cars, depending on the specific design of the bumper and equipment. The parts are primarily intended for customers who are looking for a replacement for damaged or missing covers – typically after a minor collision, improper disassembly or damage during a vehicle wash.

Technical information:
Manufacturer: PSA Citroën Peugeot
Model: Citroën C5 II
Product codes: 7414JC, EYLC
Other numbers: color designation EYL – Iceland gray lacquer, NFP (status in original catalog)

Thanks to the listed product codes, it is possible to find a match with the original part more precisely, especially if the part was originally identified only by number. This will be especially appreciated by auto mechanics and people who repair Citroën and Peugeot cars themselves and often look for specific codes in online catalogs.

Installation recommendations:
Before assembly, check the fastening in the bumper and the condition of the holders of the washer mechanism, or of the blanking elements. Install in a clean and degreased environment so that the caps fit well and nothing prevents their movement when used with nozzles. When fitting, do not use excessive force to avoid damaging the plastic grips – the caps should snap into place with smooth pressure. If necessary, we recommend professional assembly at a service center or by an experienced auto mechanic, especially if disassembly of the bumper or adjustment of the complete headlight washer system is required.

This rear lower lamp harness is a direct-fit solution for Citroën C5 I and C5 II Estate models, commonly searched under product code 6534JZ. Designed for professional workshops and experienced DIY mechanics, the harness carries the bulb sockets and wiring that power the lower rear lamp cluster. It is a practical spare part when the original wiring is damaged by corrosion, impact, or water ingress. The unit is sold as shown; bulb condition and function are not guaranteed.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C5 I Estate, Citroën C5 II Estate
• Product Codes: 6534JZ
• Other Numbers: NFP

Compatibility And Applications

Fits rear lower lamp assemblies on Citroën C5 I (first generation) and Citroën C5 II (second generation) Estate/Kombi body styles. Ideal for replacing a damaged lamp harness after rear bumper removal or light cluster repair. Always confirm physical connector shape and mounting points before installation.

Function And Typical Fault Symptoms

The harness provides electrical connections and bulb sockets for the lower rear lamp, delivering power, ground, and retaining the bulbs in the lamp housing. Common symptoms of a failing harness include intermittent lighting, blown fuses, melted or discoloured connectors, visible corrosion on contacts, or complete loss of the affected lamp function. Wiring damage after a minor collision or persistent water ingress are frequent causes.

Replacement Procedure

1. Prepare: Park on a level surface, engage parking brake, and disconnect the negative terminal of the battery before any work on the electrical system.
2. Access: Remove interior trim from the tailgate or trunk side panel to reach the rear light cluster and harness routing. On some models the bumper or lower trim may need partial removal for clear access.
3. Disconnect: Unclip and unplug the harness connectors from the lamp cluster. Remove retaining clips or screws that secure the harness to the bodywork.
4. Swap: Replace the damaged harness with the new unit, routing it along the original cable path and refitting all clips and grommets to maintain sealing against moisture.
5. Test: Reconnect the battery and test all rear light functions (brake, tail, turn, reverse as applicable) before reassembling trim. Ensure connectors are dry and secure.
6. Finalize: Refit interior panels and any removed trims. Verify lights again after a short test drive.

Installation Recommendations

Use dielectric grease on connector pins to slow corrosion and improve contact reliability. Replace any cracked grommets or damaged clips to maintain a watertight route. When routing the harness, avoid tight bends and places where abrasion against body panels can occur. If bulbs are old or show signs of overheating, replace them at the same time to avoid recurrent connector damage.

Why This Part Commonly Fails

Failures Most Often Result From Corrosion And Water Ingress, Mechanical Damage From Impacts, Or Connector Overheating Due To Poor Contact. Over Time, Road Moisture And Salt Can Penetrate Seals And Degrade Contacts; Vibration And Physical Strain Can Cause Wire Breaks Or Detached Sockets.

Note For Professional Use

Product Number 6534JZ Is A Common Search Term For This Harness. Recommended For Repair Shops And Skilled Hobbyists Who Have Experience With Rear Light Cluster Removal And Electrical Diagnostics.

This genuine-style replacement right rear lower tail lamp is designed for Citroën C5 Estate (station wagon) first and second generation models. Built to match the original fit and mounting points, it restores rear visibility and signalling performance after accident damage, ageing or moisture-related failures. The part is commonly searched by its product codes (e.g. 9637356480, 6351P7), so including those references helps quickly locate the correct unit.

Key Features

• Direct-fit right rear lower tail lamp for Citroën C5 I and II Estate models.
• Complete lamp housing; bulb holders and bulbs are available separately.
• OE-referenced product codes for easy lookup and compatibility matching.
• Designed for workshop replacement or competent DIY installation.

Benefits For Mechanics And DIYers

Fast replacement with correct fitment reduces downtime after minor collisions or water ingress. The lamp assembly allows transfer or separate purchase of bulb holders, so you can replace only the failed components if preferred. Clear product codes in the listing (9637356480, 6351P7) make it simple to find the right part in catalogs and search engines.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C5 I & C5 II Estate (Station Wagon)
• Product Codes: 9637356480, 6351P7, 6351.P7
• Other Numbers: 6351.P7 | 6351P7 | 9637356480

Installation Instructions

Basic replacement procedure (general guide; follow vehicle manufacturer service manual for exact steps):

1. Park vehicle on a level surface, switch off ignition and remove ignition key.
2. Disconnect the negative battery terminal to avoid short circuits when working with electrical connectors.
3. Access the lamp from inside the luggage compartment by removing the trim panel covering the rear light area.
4. Unscrew the retention screws or nuts holding the lamp to the body and carefully pull the lamp assembly out a short distance to access the electrical connector.
5. Unplug the connector and remove the old lamp. If reusing bulb holders, extract them before fitting the new housing; otherwise fit new holders/bulbs as required.
6. Install the new lamp, reconnect the electrical plug, secure the screws/nuts and refit the trim panel. Reconnect the battery and test all light functions (tail, stop, indicator, reverse where applicable).

Mounting Recommendations

• Always disconnect the battery before beginning work to prevent electrical damage or short circuits.
• Inspect the lamp sealing surface and replace or renew any damaged gaskets to prevent future moisture ingress.
• If bulb holders are corroded or sockets show heat damage, replace them rather than reusing to ensure reliable contact.
• Tighten mounting hardware to manufacturer torque values where specified, and avoid overtightening plastic fasteners to prevent cracking.

Why This Part Commonly Fails

• Moisture Ingress: Cracked lenses or worn seals allow water into the housing, causing condensation, short circuits or corrosion of bulb holders and contacts.
• Impact Damage: Rear parking incidents or loading impacts often crack or break the lower lamp housing.
• Bulb And Socket Wear: Repeated heat cycling and vibration can degrade bulb holders and contacts, causing intermittent or failed lighting.
• Aging And UV Exposure: Over time, plastics can become brittle and mounting tabs or seals fail.

Notes On Compatibility And Search

Customers frequently search by product codes (9637356480, 6351P7). Verify the code in the listing against the part required for your Citroën C5 Estate generation. Bulb holders are not always included and can be purchased separately if needed.

Recommendation

For workshop fitting, use correct trim and body removal tools to avoid damage. Test all light functions after installation. If electrical faults persist after changing the lamp, check wiring harness, fuses and ground points for corrosion or damage.

The left rear lower lamp for Citroën C5 I and II Kombi is intended for installation in the rear bumper on the left side of the car. This is a used original part from the PSA concern, which is suitable as a full replacement for a damaged or non-functional light. Properly functioning rear lighting is important not only from the point of view of technical inspection, but also traffic safety, as it ensures better visibility of the car in poor lighting conditions.

This lamp comes without wiring and without bulbs, which must be used from the original light or purchased new. This gives you the opportunity to install new bulbs straight away and thus prevent further disassembly due to their replacement.

Technical information:
Manufacturer: PSA / Citroën / Peugeot
Model: Citroën C5 I Kombi, Citroën C5 II Kombi
Location: left rear lower lamp (rear bumper, left side)
Product codes: 9637356580, 6350P7
Other numbers: NFP (the part is no longer commonly available in the original)
Condition: used car part from Citroën C5 / Peugeot (PSA)
Purpose: spare part for the repair of the rear lighting of the body

Thanks to the listed original numbers 9637356580 and 6350P7, the part can easily be compared with the original lamp removed from the vehicle. Matching these numbers is key to proper compatibility. This type of rear lower lamp is typically used for functions such as rear fog light or reversing light (depending on the specific equipment of the car).

Installation recommendations:
– Before mounting, compare the physical shape, mounting and connector of the lamp with the original part.
– Check the seal and clean or replace if necessary to prevent water from entering the lamp.
– When assembling, first place the light in the correct position and only then tighten the screws to avoid cracking the plastic.
– Use suitable light bulbs according to the vehicle manufacturer’s specifications and keep the glass and bulbs clean (do not touch the bulb of halogen bulbs with your bare hands).
– After connecting, check all light functions (fog, reverse or other functions depending on the equipment) before finally tightening and closing the bumper or panels.
– Installation in a dry environment and with the car ignition off is recommended to avoid damage to the electrical installation.

This left rear lower lamp is a suitable choice for car mechanics and DIYers who are looking for a functional used original part for the first and second generation Citroën C5 Kombi and want to preserve the original appearance and safety functions of the car’s lighting.

This left rear upper lamp is a direct-fit replacement for Citroën C5 Estate models (both first and second generation). Designed for professional workshops and DIY mechanics, the assembly restores rear lighting functionality and road safety after collision damage, cracked lenses, or electrical faults. Many buyers search by OE codes 9637356380 or 6350P9, so the exact product numbers are included for quick identification.

Benefits And Application

High-quality body lamp housing engineered to match the original mounting points and connector locations of the Citroën C5 Estate. The part simplifies repairs by minimizing modification work: bolt-on fitment with original-style seals and connectors. Suitable for mechanics replacing a damaged rear cluster or for owners performing a panel repair.

How The Part Functions

The upper rear lamp houses the rear lighting elements and their sockets (tail light/brake light/indicator arrangement depends on vehicle equipment). It protects bulbs and wiring from the elements while maintaining the correct light output pattern and visibility required for road safety.

Replacement Procedure

• Open the tailgate and remove the interior trim panel to access the lamp mounting screws and electrical connector.
• Unscrew the securing bolts and carefully pull the lamp assembly outwards to expose the wiring harness.
• Disconnect the electrical connector and remove the lamp. If needed, swap the bulb socket into the new assembly (sockets may be purchased separately).
• Fit the new lamp, connect the wiring, check alignment and sealing, then secure the mounting screws and refit the trim panel.
• Test all lighting functions (tail, brake, indicator, reverse if applicable) before returning the vehicle to service.

Installation Recommendation

Install Using Standard Workshop Tools. Turn Off Ignition And Remove The Key Before Working On Lighting Circuits. Ensure Seals And Fasteners Are Clean To Maintain Waterproofing. Replace Bulb Sockets If Corroded. After Installation, Verify All Functions From Outside The Vehicle And Use A Helper To Operate Brake And Indicator Controls.

Most Common Failure Reasons

• Impact Damage From Minor Collisions Causing Cracked Lenses Or Broken Mounting Tabs.
• Water Ingress Through Damaged Seals Leading To Corrosion Or Short Circuits.
• Burnt Or Intermittent Bulb Contacts Due To Age Or Poor Socket Condition.
• Corroded Or Damaged Connector Pins And Wiring Caused By Moisture Penetration.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C5 I Estate, Citroën C5 II Estate
• Product Codes: 9637356380, 6350P9
• Additional Numbers: NFP

Notes For Buyers

Part Often Searched By OE Numbers 9637356380 And 6350P9. Confirm That You Require The Upper Rear Lamp For The Left/Driver Side Of Estate (Kombi) Body Style. Bulb Socket And Bulb May Be Supplied Separately — Check Product Listing For Included Items.

Description

This right rear upper tail light is a direct-fit replacement for Citroën C5 Kombi (Estate) models. Designed to match the original mounting points and connector layout, it restores proper rear signaling and appearance after impact, cracking or weather-related damage. Popularly searched by part numbers 9637356280 and 6351P9, this unit is suitable for professional garages and experienced DIYers looking for a dependable exterior lighting replacement.

Features

• Direct-fit replacement for the right rear upper tail lamp assembly.
• Original-style housing and lens for factory appearance.
• Connector layout compatible with standard Citroën C5 Kombi wiring harness.
• Bulb holder and bulb available separately to allow flexible repair options.
• Ideal when searching by OEM codes 9637356280 or 6351P9.

Compatibility

Compatible With: Citroën C5 I (Kombi) And Citroën C5 II (Kombi). Right Side (Passenger Side).

Installation Recommendations

Basic replacement procedure suitable for mechanics and competent DIYers:

1. Disconnect The Battery Before Starting To Avoid Short Circuits And Protect Vehicle Electronics.
2. Open The Tailgate And Remove The Interior Trim To Access The Lamp Assembly.
3. Unscrew The Retaining Bolts Or Clips And Carefully Pull The Lamp Outwards.
4. Disconnect The Electrical Connector And Remove The Bulb Holder (If Present).
5. Fit The New Lamp, Reconnect The Electrical Connector And Check All Functions (Tail, Brake, Indicator; Reverse If Applicable).
6. Refit Fasteners And Interior Trim, Ensure Seals Are Intact To Prevent Water Ingress.

If The Bulb Holder Is Not Included, Purchase The Appropriate Holder And Bulb Separately According To The Vehicle Specification.

Most Common Failure Reasons

• Impact Damage From Rear-End Collisions Or Parking Accidents Causing Cracks Or Broken Mounts.
• Water Ingress Through Damaged Seals Leading To Condensation, Corrosion Or Electrical Faults.
• Connector Corrosion Or Loose Contacts Causing Intermittent Lighting.
• Plastic Ageing And UV Damage Resulting In Discoloration Or Reduced Light Output.
• Broken Mounting Tabs From Overstress During Removal Or Minor Impacts.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C5 I And Citroën C5 II Estate (Kombi)
• Product Codes: 9637356280, 6351P9
• Other Numbers: NFP

This tail light is a practical, searchable replacement option for workshops and experienced DIY customers maintaining Citroën C5 Kombi vehicles. Always verify fitment by comparing the part numbers listed above with the unit being replaced before installation.

Are you searching for high-quality replacement parts for your Citroën C5 II? Our set of headlight washer covers is an ideal choice to maintain both the original look and functionality of your vehicle. These covers, designed specifically for Citroën C5 II models, can be used even without washer nozzles as convenient blanking caps. Additionally, their gray aluminium color perfectly complements the original design of your car.

Using our product allows you to easily restore your vehicle’s aesthetic appearance while ensuring the proper function of the headlight washers. These washer covers not only help return your car to its original condition but also protect the washers from damage and dirt, extending their lifespan.

Technical Information

• Manufacturer: PSA
• Model: Citroën C5 II
• Product Codes: 7414JC EZRC NFP
• Additional Numbers: 7414JC

Using original replacement parts guarantees maximum compatibility and long-term reliability. With increasing demands on automotive safety and functionality, it is more important than ever that all components operate perfectly as intended. The headlight washer covers for Citroën C5 II with codes 7414JC meet these standards. Investing in quality replacement parts means investing in keeping your vehicle in prime condition.

Don’t hesitate to take this opportunity to repair or upgrade your vehicle with headlight washer covers specifically designed for the Citroën C5 II. You can select our products with confidence in their quality and durable reliability, ideal for any repairs or replacements of damaged parts. Ensure your car continues to look great and operate flawlessly.

Are you looking for reliable and proven auto parts for your Citroën C5 II? Check out our offer of a used rear lamp socket with wiring, ready for easy installation in your vehicle. This part is an excellent choice for mechanics and DIY enthusiasts seeking quality replacement parts at an affordable price.

Our rear lamp socket with wiring is designed for Citroën C5 II and is fully compatible with both sides of your car – the right and left rear outer lamp. With its help, you can quickly and effectively restore the functionality of your vehicle’s rear lights. Note: The functionality of the built-in bulbs is not guaranteed, so we recommend checking their condition after installation.

Technical Information

• Manufacturer: PSA Citroën Peugeot
• Model: Citroën C5 II
• Product Codes: 89032703, 6350V3, 6351V3, NFP

This part is highly sought after for its critical role in the functionality and safety of your vehicle. Rear lights are essential for vehicle visibility and should always be in perfect technical condition, especially during nighttime or reduced visibility conditions. Replacement is relatively easy, and you can do it yourself or with the help of a professional mechanic. If you are unsure about the installation, we recommend ordering installation from our specialized partner.

Investing in quality used auto parts, such as this rear lamp socket with wiring, not only saves your costs compared to buying a new part but also contributes to sustainability and recycling of materials. Get a reliable part that will extend the life of your vehicle and ensure safe driving.

Don’t hesitate and take the step to restore the full functionality of your Citroën C5 II today. Used auto parts for Citroën and Peugeot are an effective solution for your repairs. This product is ready for immediate dispatch for your maximum satisfaction.

Mechanics and car enthusiasts often encounter issues with lamp sockets due to wear and tear, which can result from exposure to moisture and heat. This part replaces faulty sockets, providing a reliable connection for your vehicle’s lighting needs.

Designed specifically for the Citroën C5 II, this socket comes with a wiring segment, allowing for a seamless fit. The functionality of bulbs is not guaranteed, so it’s recommended to check your existing bulbs and ensure compatibility when installing.

Technical Information

Manufacturer: PSA Citroën Peugeot

Model: Citroën C5 II

Product Codes: 89032703

Other Numbers: Not applicable