Product Description

This genuine right rear wing tail light is designed for the Citroën C3 II (A51) and replaces the factory lamp on the passenger side. The unit is supplied without bulb holders, allowing you to reuse the original sockets or fit new holders and bulbs as needed. Ideal for professional workshops and DIY enthusiasts looking for an exact-fit replacement that restores original appearance and lighting function.

Key Benefits

• Direct OEM fit for Citroën C3 II (A51) — ensures correct alignment and sealing.
• High-quality lens and housing for optimal light output and durability.
• Sold without bulb holders so you can reuse existing components or upgrade bulbs separately.
• Often searched by product codes 9673805380 and 6351KQ — quick lookup for mechanics and parts specialists.

Technical Information

• Manufacturer: Citroën / Stellantis
• Model: Citroën C3 II (A51)
• Product Codes: 9673805380, 6351KQ
• Other Numbers: 9673805380 | 6351KQ

Installation Recommendations

Installation is straightforward for experienced technicians. General steps:

• Access the rear lamp from inside the trunk or by removing the inner wheel-arch liner, depending on vehicle trim.
• Remove retaining screws or clips and carefully detach the lamp assembly, watching for plastic mounting tabs.
• Unplug the electrical connector and remove the old lamp. Fit the new lamp, connect the wiring and check alignment.
• Install bulb holders and bulbs if required, then test all light functions (tail, stop, indicator, reverse) before final reassembly.
• Always handle the lens carefully to avoid scratches. Replace any damaged mounting clips to ensure secure fitment.

Why This Part Fails

The most common causes of tail light failure are moisture ingress leading to condensation and corrosion of contacts, cracked or damaged lens from impacts, broken mounting tabs from stress or previous poor installations, and connector or wiring corrosion. Bulbs and bulb holders are also frequent failure points — note that this unit is supplied without bulb holders.

Notes For Mechanics And DIYers

• Search by OEM codes 9673805380 or 6351KQ for fast identification.
• Check mounting tabs and sealing surfaces when fitting to prevent future water ingress.
• Replace bulbs and holders if they show signs of wear or corrosion to ensure reliable operation.

Product Overview

Replacement bulb holder/socket for the right rear lamp mounted in the wing (fender) of Citroën C3 II (A51). Designed for mechanics and DIY enthusiasts who need a reliable, easy-to-fit part when the original socket is damaged, corroded or the wiring has been compromised. Commonly searched under part number 6351KQ for quick identification.

Features And Benefits

• Direct replacement for the right rear lamp socket in the wing, matching original fitment.
• Supplied with a short wiring lead to simplify connection to the vehicle harness.
• Restores secure electrical contact and proper bulb seating to eliminate flicker and intermittent faults.
• Simple to install with common hand tools — saves time in the workshop compared with repairing damaged wiring.

Compatibility

Fits Citroën C3 II (A51) — right rear lamp in the wing/fender. Often identified by product code 6351KQ.

Installation

• Park the vehicle on a level surface and switch off the ignition.
• Access the rear light cluster from inside the luggage compartment or by removing the appropriate trim panel to reach the lamp holder.
• Disconnect the vehicle battery or at least isolate the lighting circuit to avoid short circuits while working.
• Remove the tail light cluster fasteners and carefully extract the cluster to access the old socket.
• Unplug the original holder from the vehicle harness and note pin positions. Cut or disengage the old holder as required.
• Connect the new holder using the supplied wiring lead. Use proper crimps or solder joints and protect connections with heat shrink or dielectric grease to prevent corrosion.
• Refit the lamp cluster, restore the battery connection and test all rear light functions (stop, tail, indicators, reverse if applicable).
• Reassemble trim and ensure the lamp housing seals correctly to prevent water ingress.

Maintenance And Expected Lifespan

Lifespan depends on exposure to moisture, salt and vibration. Typical life is several years in normal conditions, but may be shortened by persistent water ingress, road salt or repeated bulb overheating. Inspect sockets during routine light checks and replace at first sign of corrosion, loose contacts or melted plastic.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C3 II (A51) — Right Rear Lamp (Wing)
• Product Codes: 6351KQ
• Additional Numbers: Not specified

Installation Recommendations

• Use quality electrical connectors and insulate joints with heat shrink to ensure long-term reliability.
• Apply a thin film of dielectric grease to contacts to reduce oxidation and improve conductivity.
• Check the lamp housing seal and replace any damaged gaskets to prevent future water damage to the socket.
• When possible, test the new socket with a multimeter for continuity before final reassembly.

Most Common Failure Causes

• Corrosion from water ingress or condensation inside the lamp housing.
• Mechanical damage from impact or when removing/ refitting the lamp cluster.
• Heat damage caused by faulty bulbs or poor contact leading to arcing and melting of the socket.
• Wiring abrasion or connector fatigue caused by vibration and movement over time.

Notes For Buyers

If you regularly search by part number, 6351KQ is the reference commonly used for this bulb holder. Suitable for professional workshops and competent DIYers who follow safe installation practices and seal the lamp housing correctly after replacement.

This high-mounted third brake light is a direct-fit replacement for Citroën C3 II (A51) models produced from 2009 to 2016. Intended for professional workshops and DIY mechanics, the unit restores brake-signal visibility at the roofline, improves road safety and keeps the vehicle compliant with road regulations. The part is commonly searched by OEM references 9683116580 and 6351JS.

Key Features

• Direct OEM Fit For Citroën C3 II A51 (2009–2016).
• High-Level Brake Light Location For Improved Visibility.
• Complete Assembly Includes Lens, Housing And Light Module.
• Quick Identification By Part Numbers 9683116580 / 6351JS.

Technical Information

• Manufacturer: Citroën / Stellantis
• Model: Citroën C3 II (A51) 2009–2016
• Product Codes: 9683116580
• Other Numbers: 6351JS

Installation Recommendations

Replacing the third brake light on a C3 II is straightforward for a trained mechanic or an experienced DIYer. Typical replacement steps:

• Open the tailgate and remove the interior trim panel or access cover to reach the lamp fasteners. Keep clips and screws in a safe place.
• Unscrew or unclip the lamp assembly and carefully disconnect the electrical connector. Inspect the connector for corrosion or damaged pins.
• Fit the new assembly into the roof/tailgate recess, reconnect the electrical plug and secure the unit with the original fasteners. Ensure the seal sits correctly to prevent water ingress.
• Reinstall interior trim, check that no wires are pinched, and test the brake light operation (apply the brake pedal or use a helper). Verify proper illumination and alignment.

Use appropriate trim tools to avoid damaging interior panels. If the connector shows signs of corrosion, clean or replace it before installation. Ensure the roof/tailgate sealing surface is clean to maintain watertightness.

Why This Part Usually Fails

• Moisture Ingress: Water penetration around the seal causes corrosion of contacts or failure of the light module.
• Impact Or Body Damage: Rear impacts or pressure on the tailgate can crack the lens or damage mounting points.
• Electrical Issues: Corroded connectors, broken wiring, or intermittent ground connections lead to failure or flicker.
• Component Aging: LEDs or bulbs may degrade over time due to thermal cycling and vibration.

Practical Tips

• Check and replace damaged seals to prevent repeat failures.
• Inspect the wiring harness and connector for corrosion—apply dielectric grease if appropriate.
• After installation, verify both functionality and that the light is securely mounted to prevent rattles or water entry.

This product is ideal for restoring the original appearance and function of the Citroën C3 II third brake light position. Search by the OEM numbers for fast lookup and correct fitment.

High-quality left rear reflector designed for the tailgate of Citroën C3 II (A51) models from 2009 to 2016. This direct-fit replacement restores rear visibility and legal compliance while maintaining the original appearance of the vehicle. Ideal for professional workshops and experienced DIYers who search by product code — listed codes ensure fast lookup in parts catalogs and help you find the correct unit quickly.

Key Features

• Direct Fit For Citroën C3 II (A51) 2009–2016.
• OEM-Style Design Ensuring Correct Appearance And Light Reflection.
• Durable Plastic Construction Resistant To Road Debris.
• Simple Replacement Procedure Suitable For Mechanics And Competent DIYers.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C3 II (A51) 2009–2016
• Product Codes: 9685225580, 89090139
• Other Numbers: 6350JC

Compatibility

Fits Left Side Tailgate Applications On Citroën C3 II (A51) Produced Between 2009 And 2016. Use The Listed Product Codes To Confirm Fitment In Your Parts System.

Installation Recommendations

Replacement Is Straightforward For Trained Technicians And Savvy DIYers. Typical Steps:

• Open Tailgate And Remove Interior Trim Panel To Access Reflector Mounting Area.
• Release Retaining Clips Or Unscrew Fasteners Securing The Old Reflector.
• Carefully Pry Out The Old Reflector To Avoid Damaging Surrounding Trim; Inspect Mounting Tabs And Replace Any Broken Clips.
• Fit New Reflector By Aligning Mounting Tabs, Pressing Into Place Until Clips Engage, Or Reinstalling Screws.
• Check Sealing And Alignment; If Water Ingress Was Present, Clean The Area And Consider Appropriate Sealant Around The Mounting Perimeter.

Estimated Time: 15–45 Minutes Depending On Access And Whether Trim Fasteners Need Replacement. Use Basic Hand Tools And Plastic Trim Tools To Avoid Damage.

Why This Part Fails

Reflectors Typically Fail Or Require Replacement Due To:

• Impact Damage From Loading The Boot, Minor Collisions Or Road Debris Causing Cracks Or Breakage.
• Broken Or Fatigued Mounting Tabs From Repeated Removal Or Plastic Ageing.
• Water Ingress Or Seal Failure Leading To Fogging Or Reduced Reflectivity.
• UV Exposure And Surface Wear Reducing Reflective Performance Over Many Years.

Notes For Professionals

Keep Replacement Clips And Fasteners On Hand When Carrying Out Body Repairs To Ensure A Neat Finish. Inspect Surrounding Trim And Tailgate Seal To Prevent Recurring Water Ingress Issues.

Buy Now To Restore Correct Rear Reflectivity And Maintain Vehicle Safety And Compliance — Fast Shipping And Clear Product Codes Make Identification Simple For Workshops And DIY Enthusiasts.

Overview

This right rear tailgate reflector is designed for Citroën C3 II (A51) models produced between 2009 and 2016. It restores the original rear visibility and road safety marking on the tailgate, ensuring the vehicle remains compliant with reflector and visibility requirements. Ideal for professional workshops and DIY mechanics, the part is commonly searched by OE numbers and aftermarket references.

Fitment And Function

Fitment: Citroën C3 II (A51) 2009–2016 (Right Side, Tailgate). Confirm compatibility by matching the vehicle model and the part numbers listed below.

Function: The reflector provides passive rear visibility by reflecting light from other vehicles. It does not contain electrical components. Properly positioned reflectors improve safety during night-time and low-light conditions and are integral to the rear lighting cluster appearance.

Replacement Procedure

The replacement is straightforward and suitable for a competent DIYer or professional mechanic. Typical steps:

• Open the tailgate and remove the inner trim panel to access the reflector mounting area (use plastic trim tools to avoid damage).
• Locate and release any retaining clips or fasteners holding the reflector; some versions are secured with screws or plastic rivets.
• Carefully withdraw the old reflector from the tailgate recess and clean the mounting surface of dirt and corrosion.
• Install the new reflector, ensuring clips or fasteners engage securely and the part sits flush with the bodywork.
• Reinstall the inner trim and verify correct fitment and alignment. No electrical reconnection is required for passive reflectors.

Technical Information

• Manufacturer: Stellantis (Citroën)
• Model: Citroën C3 II (A51) 2009-2016
• Product Codes: 9685225480
• Additional Numbers: 89090140, 6351JC

Installation Recommendations

Use appropriate trim tools to avoid damaging the tailgate trim and paint. If fasteners are corroded or damaged, replace them with equivalent clips or screws. After installation, check that the reflector is seated evenly and that gaps to the bodywork are consistent to prevent water ingress. For repairs after collisions, inspect surrounding mounting points and the tailgate structure for deformation before fitting the new reflector.

Most Common Failure Reasons

Reflectors are passive and rarely ‘fail’ electrically, but they commonly require replacement due to:

• Impact Damage: Rear parking collisions or knocks to the tailgate that crack or break the reflector.
• Physical Wear: Scratches, abrasions, or loss of reflective surface from road debris and repeated cleaning.
• Mounting Clip Failure: Plastic clips or tabs can become brittle and break with age or during removal.
• Moisture Ingress: Seals or poor fitment allowing water to collect behind the reflector, causing fogging or reduced reflectivity.

Replacing a damaged reflector restores both safety and the original appearance of the rear of the vehicle. For workshops, stocking the common OE numbers listed above increases service speed for Citroën C3 II repairs.

High-quality Genuine Replacement Rear Wing Lamp designed for Citroën C3 II (A51). This left side rear lamp assembly restores proper rear lighting functions and fitment in the wing (fender), matching original OEM dimensions and mounting points. Ideal for professional workshops and DIY mechanics who need a direct-fit lamp with original part numbers 9673805480 / 6350KQ for fast identification and ordering.

Key Benefits

• Direct Fit For Citroën C3 II (A51) — Easy Replacement Without Body Modifications
• OEM Part Numbers Included For Quick Search: 9673805480, 6350KQ
• Robust Construction With Accurate Mounting Points To Ensure Correct Alignment
• Sold Without Bulb Holders — Allows Use Of Existing Sockets Or Choice Of New Bulbs
• Suitable For Professional Repair Shops And Competent DIY Mechanics

How It Works And What It Does

This lamp assembly provides the rear lighting functions assigned to the left wing position—rear/parking light and stop/turn signal functions depending on vehicle wiring. The unit houses the light modules and lens that protect bulbs and optics from the environment while ensuring correct light output and beam distribution for rear visibility and signalling.

Replacement Procedure

Typical replacement steps (general guide for experienced mechanics):

• Access The Lamp From Inside The Trunk Or Wheel Arch By Removing Trim Panels Or The Wheel Arch Liner As Required.
• Unscrew The Mounting Fasteners Securing The Lamp To The Wing. Keep Fasteners For Reuse If Intact.
• Disconnect The Wiring Harness And Remove Bulb Holders If Present. Note: This Unit Is Supplied Without Bulb Holders.
• Fit The New Lamp Into The Wing, Reconnect The Wiring Harness, Reinstall Fasteners And Trim Panels, Then Test All Functions (Tail, Brake, Indicator).
• Adjust Alignment If Necessary To Ensure Even Gaps And Proper Seal Against The Bodywork.

Technical Information

• Manufacturer: Citroën / Stellantis
• Model: Citroën C3 II (A51)
• Product Codes: 9673805480, 6350KQ
• Additional Numbers: 6350.KQ, A51

Installation Recommendations

• Work With The Vehicle On A Stable Surface And Use Proper Lighting.
• Disconnect The Negative Battery Terminal Before Starting Work To Avoid Short Circuits And Damage To Electrical Components.
• Inspect Wiring Harness Contacts For Corrosion Or Damage; Clean Or Replace Connectors If Poor Contact Is Found.
• Use Appropriate Torque On Mounting Fasteners And Ensure The Lamp Seals Correctly Against The Body To Prevent Water Ingress.
• If You Replace Bulb Holders Or Bulbs, Use Correct Types And Ratings Specified For The Vehicle.

Why This Part Commonly Fails

Rear wing lamps most often fail or require replacement because of:

• Impact Damage From Minor Collisions Or Parking Scrapes Causing Cracked Lenses Or Broken Mounts.
• Water Ingress Due To Damaged Seals Or Corroded Mounting Points Leading To Electrical Faults Or Oxidised Contacts.
• Vibration And Age Leading To Hairline Cracks, Loose Mounts Or Degraded Optical Performance.
• Faulty Or Missing Bulb Holders/Sockets Resulting In Intermittent Lighting (Note: This Unit Is Supplied Without Bulb Holders).

Choosing the correct OEM-numbered lamp (9673805480 / 6350KQ) reduces fitment issues and helps ensure a durable repair. For garage professionals and experienced DIYers this unit provides a reliable, original-fit solution for the left rear wing on Citroën C3 II (A51).

Product Overview

Replacement bulb holder (socket) for the left rear fender tail lamp of Citroën C3 II (A51). This unit includes a short wiring lead for direct connection to the vehicle harness and is commonly found under product codes 6350KQ / 6350.KQ. Ideal for professional workshops and experienced DIY mechanics who need a quick, reliable fix for intermittent or failed rear light circuits.

Function

The socket secures the bulb in the rear lamp assembly and provides the electrical contacts required for brake, tail or indicator functions (depending on the fitted bulb). It also positions the bulb correctly and helps keep electrical contacts stable under vibration.

How It Is Replaced

Replacement typically requires access to the rear lamp assembly from the boot or the wheel-arch side, depending on body style and local trim layout. Remove the relevant trim or inner wing liner to reach the lamp backplate, unplug the old socket from the wiring harness, release any retaining clip or twist-lock holding the socket, remove the faulty socket and insert the new one. Reconnect the wiring lead, refit trims and test all lamp functions (tail, brake, indicator) before finishing. If unsure about access points on a specific vehicle, follow the vehicle manufacturer’s removal procedure.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C3 II (A51)
• Product Codes: 6350KQ, 6350.KQ
• Additional Numbers: N/A

Installation Recommendations

Always work safely: disconnect the negative battery terminal before starting electrical work to avoid short circuits. Inspect connector pins for corrosion or damage and clean contacts if necessary. Apply a small amount of dielectric grease to contacts to reduce future corrosion. Ensure the socket is fully seated and any retaining clips are engaged. After installation, verify all relevant light functions and check for error messages on vehicles equipped with monitoring systems.

Why This Part Commonly Fails

Common failure causes include corrosion from moisture ingress, brittle or cracked plastic after prolonged heat cycling, broken or fatigued wire leads from vibration, and poor contact due to worn or oxidised pins. These failures typically present as intermittent lighting, flickering, or a complete loss of a lamp function. Regular inspection of rear lamp seals and connectors helps prevent premature failures.

Notes For Buyers

Mechanics and DIYers often search using the product code (e.g. 6350KQ). Check the physical connector shape and pin arrangement when replacing to ensure fitment. This listing covers the left rear lamp socket for Citroën C3 II (A51) and includes the attached wiring lead for straightforward replacement.