This right rear tail lamp is a direct-fit replacement for the Citroën C2 and is ideal for professional workshops and DIY mechanics looking for a reliable OEM-quality part. Supplied under code 6351S7, the unit restores rear light functions including tail, brake, indicator and reverse (depending on vehicle specification) and helps maintain road safety and vehicle appearance. Clear, searchable identifiers such as Citroën C2, rear light and 6351S7 improve findability for technicians searching by part number.

Key Features

• Direct replacement for Citroën C2 rear right lamp — designed to original equipment specifications.
• OEM quality: ensures correct fit, alignment and light output for brake, tail and indicator functions.
• Part Number: 6351S7 for fast identification and ordering.
• Complete lamp assembly ready to install — includes housing, lens and sockets (bulbs sold separately depending on version).

Function And Typical Failure Modes

The rear lamp assembly houses the signal and illumination bulbs (or LEDs on some versions) and provides sealed protection against moisture and dust. The most common reasons for replacement are cracked or faded lenses from impact or UV exposure, water ingress causing corrosion or electrical faults, and broken mounting points after minor collisions. Burnt bulbs or socket corrosion can also cause light failure, but in many cases the entire assembly is replaced to restore correct beam pattern and alignment.

Replacement Procedure (General Guide)

• Prepare: Park on level ground, switch off ignition and, for safety, disconnect the negative battery terminal when working on electrical connections.
• Access: Open the boot and remove the trim or access panel behind the lamp to reach the fixing nuts and wiring connector.
• Remove: Unscrew the retaining nuts or bolts, carefully pull the lamp assembly out, and disconnect the wiring harness by unclipping the connector.
• Fit New Unit: Connect the wiring harness to the new lamp, position the assembly in the body aperture and secure with the original fasteners. Ensure correct alignment and sealing against the body.
• Test: Reconnect the battery (if disconnected) and test all light functions — tail, brake, indicator and reverse — before reassembling interior trim.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C2
• Product Codes: 6351S7
• Other Numbers: No additional numbers available

Installation Recommendations

Use original or OEM-spec fasteners and replace any damaged clips to ensure a secure fit and proper sealing. If water ingress is present, inspect surrounding body seals and repair corrosion before fitting the new lamp. When replacing bulbs, use the correct type and wattage specified by the vehicle manufacturer to avoid overheating and premature failure. After installation, verify alignment and operation of all functions.

Why This Part Fails Most Often

Rear lamps typically fail due to physical damage (impacts, parking knocks), environmental degradation (UV fading, cracked lenses) and moisture ingress leading to electrical faults or corrosion. Poor sealing around the lamp aperture accelerates damage. Replacing the complete assembly is often the most reliable way to restore function and water-tightness.

Order by Part Number 6351S7 to quickly locate the correct right rear lamp for Citroën C2 and ensure a fast, accurate replacement for workshop or home repair use.

Direct-fit left rear lamp for the Citroën C2, supplied as an OEM-style replacement bearing codes 9649864580 and 6350S7. This rear combination lamp restores brake, tail and indicator lighting where applicable and is designed for easy installation by professional technicians and experienced DIY mechanics. The unit offers correct optics and mounting points to match original equipment, helping to maintain vehicle safety and road legality.

Technical Information

• Manufacturer: Stellantis / Citroën
• Model: Citroën C2 (Typically 2003–2009)
• Product Codes: 9649864580, 6350S7
• Additional Numbers: NFP

Fitment And Function

This left rear lamp is a direct replacement for the rear combination lamp on Citroën C2 hatchback models. Depending on the vehicle variant, the assembly covers multiple light functions (tail, stop, and indicator). It uses the original mounting points and electrical connector format to ensure a secure fit and straightforward connection.

Installation Recommendations

1. Park The Vehicle On A Level Surface And Switch Off The Ignition.
2. Open The Tailgate And Remove Interior Trim Or Access Panel To Reach The Lamp Fixings.
3. Unscrew The Mounting Nuts Or Bolts Securing The Lamp Assembly And Carefully Pull The Lamp Outwards.
4. Unplug The Electrical Connector And Remove Bulbs If Required (Inspect Bulb Holders For Corrosion).
5. Fit The Replacement Lamp, Reconnect The Electrical Connector And Secure The Mounting Fasteners To The Correct Tightening Level.
6. Test All Light Functions (Tail, Brake, Indicator, Reverse Where Applicable) Before Reassembling Interior Trim.

Use Appropriate Hand Tools, Avoid Over-Tightening Plastic Fasteners, And Ensure Rubber Gaskets Or Seals Are Correctly Seated To Prevent Moisture Ingress.

Common Failure Reasons

• Water Ingress Causing Condensation Or Short Circuits Due To Worn Seals Or Damaged Lens.
• Impact Damage From Minor Collisions Or Bumping The Rear Of The Vehicle.
• Corroded Connector Pins Or Socket Contacts Leading To Intermittent Operation.
• Aged Or Broken Mounting Tabs Resulting In Poor Fitment And Vibration Damage.
• Bulb Failure Inside The Assembly; Check Bulb Type And Condition When Replacing The Unit.

Why Choose This Part

This left rear lamp is supplied to match original equipment specifications, making it a reliable choice for body repairs, insurance replacements and routine maintenance. Commonly searched by OE numbers 9649864580 and 6350S7, the assembly helps restore correct light output and vehicle appearance with a straightforward fitment process.

High-quality replacement rear bulb socket designed specifically for the Citroën C2. This socket secures the bulb in the tail lamp housing and provides the electrical contacts required for brake, tail, and indicator lights. Supplied with a short piece of wiring to simplify installation and ensure reliable contact. Ideal for professional auto workshops and DIY mechanics looking for a direct-fit repair part under references 6351S7 and 6350S7.

Function And Application

The bulb holder (socket) is responsible for mechanically holding the bulb and providing stable electrical connection between the vehicle wiring and the lamp. Correct operation is essential for brake light, tail light, and turn signal function. This part is used in the rear lamp assemblies on Citroën C2 models and fits both left and right tail lights.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C2
• Product Codes: 6351S7, 6350S7
• Other Numbers: Not Available

Installation Recommendation

Replacement is straightforward for experienced mechanics and competent DIYers. Typical procedure:

• Remove the tail lamp assembly from the vehicle (access from the luggage compartment; keep trim and fasteners safe).
• Twist or unclip the old bulb socket from the lamp reflector and disconnect the wiring connector.
• Fit the new socket into the lamp housing, connect the wiring harness and secure the socket in place.
• Refit the lamp assembly, tighten fasteners to the correct torque, and test all light functions (tail, brake, indicator).

Use appropriate hand tools and check seals/gaskets to prevent water ingress. If wiring is brittle or corroded, replace or repair the harness section rather than stretching the new socket wiring. After installation, verify lamp alignment and function before finishing work.

Most Common Failure Causes

• Corrosion Of Contacts: Moisture ingress or salt buildup causes poor electrical contact and intermittent lighting.
• Heat Damage: Overheating from an incorrect bulb type or poor contact can melt plastic sockets and deform contacts.
• Mechanical Wear And Vibration: Repeated removal/installation or vibration can crack the plastic or loosen the connection.
• Water Ingress And Seal Failure: Damaged lamp seals allow water to reach the socket and wiring, accelerating corrosion.

Why Choose This Part

Direct-fit design for Citroën C2 makes replacement fast and reliable. Supplied with a short wiring tail to simplify reconnection and reduce the need for splicing. Suitable for both professional garages and competent DIY repairs where a durable, OEM-compatible socket is required.

Notes

Check bulb type and lamp condition when replacing the socket. Using the correct bulb wattage and ensuring the lamp housing is dry and sealed will extend service life. Follow safe workshop practices and use proper personal protective equipment during installation.

When it comes to vehicle maintenance, replacing worn-out lights is crucial for ensuring proper signaling and safety. The Right Rear Light for Citroën C2 connects easily, making the replacement process straightforward for both professional mechanics and DIY enthusiasts. Regular inspection is recommended, as external elements and weather conditions can cause deterioration over time.

Technical Information

• Manufacturer: PSA
• Model: Citroën C2
• Product Codes: 9649864480, 6351Y0
• Additional Numbers: N/A

Replacing the Third Brake Light is a straightforward process. Typically, it can be accessed by removing the rear trim and disconnecting the old unit to install the new one. It’s advisable to check the condition of the bulb and connectors during installation to prevent future issues.

Technical Information

Manufacturer: Citroën
Model: C2
Product Codes: 6351S6
Other Numbers: Not Applicable

This high-quality headlight is specifically manufactured for Citroën C2 models. Ensuring proper visibility during night driving or in adverse weather conditions is crucial for safe driving. It is common for headlights to wear out due to factors like moisture ingress, road debris, and everyday wear, necessitating timely replacement.

Replacing your headlight is straightforward. Begin by disconnecting the battery to avoid any electrical issues. Next, remove the old headlight by releasing the retaining clips or screws. Simply position the new P Headlight in place, reconnect any wiring, and secure it with the retaining clips. Always refer to the vehicle’s manual for specific instructions.

Invest in safety and reliability with the P Headlight. Its durable construction and original specifications make it a perfect fit for Citroën C2 vehicles, ensuring longevity and performance.

Technical Information

• Manufacturer: Citroën
• Model: Citroën C2
• Product Codes: 9680128180
• Additional Numbers: 6205ZW