This replacement bulb socket is intended for the right-hand rear lamp on first generation Citroën C1 and Peugeot 107 models. It secures and connects the brake/taillight and indicator bulbs to the vehicle wiring harness. The part is commonly searched by OE and supplier numbers shown below, which makes identification and ordering straightforward for workshops and DIYers.

Technical Information

Manufacturer: Stellantis (Citroën / Peugeot)

Model: Citroën C1 (First Generation), Peugeot 107 (First Generation)

Product Codes: 634681, 81550-0H060

Other Numbers: 6351X8, 6351X6

Function And Application

The socket holds and electrically connects the rear lamp bulbs (tail/brake/indicator) to the vehicle’s wiring. It provides mechanical support, electrical contacts and, in many designs, a basic seal against moisture. This item is a direct-fit component for the right rear light cluster on the listed vehicles and is intended for use when the original socket is damaged, corroded or has poor electrical contact.

Replacement Procedure (Overview)

• Open the rear boot/trunk and remove interior trim panels or access flap to reach the lamp assembly.
• Unscrew or unclip the tail lamp fasteners and carefully withdraw the lamp housing from the body.
• Locate the bulb socket at the rear of the lamp housing, press the retaining tab and rotate or pull the socket out depending on the design.
• Disconnect the electrical connector, replace the old socket with the new one, reconnect and test the circuit before refitting the lamp housing.
• Reassemble the lamp and interior trim, ensuring all seals and fasteners are secured to prevent water ingress.

Recommendations For Installation

• Work on a cold vehicle and disconnect the battery if you will be handling multiple electrical connections.
• Check bulb condition before final assembly—this socket is supplied without guarantee of bulb functionality.
• Clean mating surfaces and connector pins; apply a light dielectric grease to contacts to reduce future corrosion.
• Inspect the lamp housing seal and replace if damaged to avoid moisture reaching the new socket.
• After installation, verify all light functions (tail, brake, indicator, and reverse if applicable) to ensure proper operation.

Why This Part Commonly Fails

The most frequent causes of socket failure are moisture ingress and corrosion of the electrical contacts, heat-related plastic degradation from bulb operation, mechanical damage during bulb changes, and general aging. Water or condensation inside the lamp accelerates corrosion and can cause intermittent connections or complete loss of contact. Poorly seated bulbs or vibration can also lead to cracked sockets or broken retaining tabs.

This socket is a practical, cost-effective repair for restoring reliable rear lamp connection and ensuring safe, legally compliant lighting on the road. Many professionals and DIY enthusiasts search by the OE numbers listed above when replacing this part.

Product Overview

This replacement bulb holder with an attached wiring pigtail is designed for the right rear lamp assembly on Citroën C1 and Peugeot 107 vehicles. It restores the electrical connection between the vehicle harness and the lamp sockets, providing a quick repair option for broken sockets, damaged leads or corroded contacts. Ideal for professional workshops and DIY mechanics who search by part number to ensure compatibility.

Key Features

• Direct fit for right rear lamp application on Citroën C1 and Peugeot 107 (first generation).
• Includes socket(s) and a piece of wiring for straightforward replacement of the damaged harness section.
• Supplied without bulbs; the functionality of bulbs is not guaranteed.
• Often stocked and searched by OE/product codes for fast identification.

Technical Information

• Manufacturer: Stellantis
• Model: Citroën C1 (First Generation), Peugeot 107
• Product Codes: 634681, 81550-0H060, 6351X8, 6351X6
• Additional Numbers: 634681, 6351X6, 6351X8, 81550-0H060

Installation Recommendations

Follow safe working practices and vehicle-specific procedures when replacing the lamp holder. Recommended steps:

1. Disconnect the vehicle battery before starting work to avoid short circuits or damage to electrical components.
2. Access the right rear lamp assembly from the boot/compartment: remove trim panels and unscrew the lamp housing fasteners.
3. Remove the lamp assembly and access the old socket/wiring. Unplug any connectors and rotate or unclip the socket to release it from the housing.
4. Fit the new holder, route the pigtail to avoid sharp edges, and secure any retention clips or grommets to maintain sealing against moisture.
5. Reconnect connectors, reassemble the lamp and test all functions (tail, stop, indicator) before reattaching trim panels.
6. Use dielectric grease on contacts to reduce corrosion risk and ensure a reliable connection.

Why This Part Fails

• Moisture Ingress: Water entry into the lamp housing causes corrosion of contacts and connectors.
• Heat Damage: High operating temperatures or incorrect bulb wattage can melt plastic sockets or deform contacts.
• Mechanical Stress: Vibration, impact, or repeated bulb changes can crack the plastic or loosen contacts.
• Electrical Contact Wear: Oxidation and loss of spring tension in contacts lead to intermittent or non-functioning lights.

How Replacement Is Performed

The bulb holder is typically replaced by removing the tail lamp assembly, disconnecting the old socket from the lamp and harness, and installing the new holder into the lamp housing. Reassembly is straightforward: secure the lamp, reconnect the battery, and verify all rear light functions. If corrosion or wiring damage extends beyond the holder, additional harness repairs may be necessary.

Practical Notes

• Searches for this part are often performed using the product codes listed above—use them to speed up identification.
• Bulbs are not included and their operation is not guaranteed with this part; check and replace bulbs if required.
• If the lamp housing shows signs of cracking or heavy moisture ingress, replace or reseal the housing to prevent repeat failures.

This replacement tail lamp bulb socket is designed for technicians and DIY motorists who maintain Citroën C1 and Peugeot 107 vehicles. The part restores a reliable electrical connection in the rear light cluster, eliminating flicker, intermittent contact and poor grounding caused by worn or damaged sockets. Frequently searched by OE and reference numbers, this item is suitable when the original holder has cracked, corroded or melted around the terminals.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C1 (First Series), Peugeot 107 (First Series)
• Product Codes: 81560-0H060, 6350X8, 6350X6
• Other Numbers: 634686

Fitment

Compatible With: Citroën C1 First Generation (2005–2014), Peugeot 107 First Generation (2005–2014). Intended For Use In Rear Light Assemblies As The Bulb Socket/Holder.

Installation Recommendations

• Prepare: Park on a level surface, switch off ignition and remove the negative terminal of the battery for added electrical safety.
• Access: Open the boot and remove the interior trim or access panel behind the tail light cluster. Unscrew or unclip the tail lamp to reach the socket.
• Remove Old Socket: Twist or unclip the old holder from the lamp housing, disconnect the wiring plug and carefully extract any retained bulb(s). Inspect wiring for heat or corrosion damage.
• Install New Socket: Insert the new holder into the lamp housing until it locks, reconnect the wiring plug and install correct bulbs. Use a dielectric grease sparingly on contacts to reduce future corrosion.
• Test: Reconnect the battery, test all rear light functions (tail, brake, indicator, reverse if applicable) before reassembling trim and securing the lamp.
• Tip: Replace compromised bulbs and clean contact surfaces to ensure long-term reliability. Avoid using higher-wattage bulbs than specified, as they accelerate socket deterioration.

Most Common Failure Causes

Bulb holders in rear lamps typically fail due to moisture ingress and corrosion, heat damage from over-wattage bulbs or poor ventilation, mechanical fatigue and cracking of the plastic after years of vibration, and loosening or burning of electrical contacts that create intermittent connection or total failure. Road salt and contaminated water accelerate corrosion, especially in vehicles used in cold climates or with frequent short trips.

Note: This listing refers to the bulb holder only. The functionality of bulbs themselves is not guaranteed and should be checked separately. Many customers search using OE numbers like 81560-0H060, 6350X8, 6350X6 or reference 634686 to find the correct replacement quickly.

This replacement bulb socket with wiring harness is designed for rear light applications on first‑generation Citroën C1 and Peugeot 107 vehicles. It provides a direct-fit electrical connection for standard rear bulbs and is commonly sought by mechanics and DIY enthusiasts under part numbers such as 634686, 6350X8 or 81560-0H060. The included pigtail cable simplifies installation when the original wiring or connector is damaged.

The part is ideal for quick repairs to restore a secure bulb connection and prevent intermittent lighting faults. Note that this listing covers the socket and short cable only; bulbs are not guaranteed to be functional and are usually replaced separately.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C1 (First Series), Peugeot 107 (First Series)
• Product Codes: 81560-0H060, 6350X8, 6350X6, 634686
• Additional Numbers: 6350.X8, 81560-060

Function And Fitment

The socket secures rear lamp bulbs in the tail light assembly and provides the electrical contact for stop, tail or indicator bulbs depending on the lamp position. The short cable section allows reconnection to the vehicle wiring loom when the original connector is cracked, corroded or the wiring is cut. This part fits the rear lamp assemblies used on first‑generation Citroën C1 and Peugeot 107 models.

Recommended Installation

1. Park on a level surface, switch off the ignition and remove the key. For safety, disconnect the negative battery terminal if you will be handling wiring extensively.
2. Open the boot and remove the trim or access panel to reach the tail light cluster. On C1/107 models this is usually accessible from inside the boot after removing a few fasteners.
3. Unscrew or unclip the tail light unit and gently pull it clear. Unplug the main connector and remove the bulb holder by pressing the locking tab and turning or pulling as required.
4. Release the old socket from the lamp, fit the replacement socket into the bulb holder, and connect the supplied cable to the vehicle loom (secure with the original connector or suitable crimp/heat‑shrink joints).
5. Test the lamp functions (tail, brake, indicator) before refitting the lamp and trim. Ensure all connections are tight and protected from moisture.

Why This Part Commonly Fails

• Corrosion: Water ingress or condensation in the tail lamp can corrode contacts and cause intermittent or failed connections.
• Heat And Vibration: Repeated heating cycles from bulbs and road vibration can crack plastic sockets and weaken contacts over time.
• Mechanical Damage: Impact, over‑tightening when refitting the lamp, or incorrect bulb removal can break the socket or wiring.
• Ageing Wiring: Insulation becomes brittle on older cars, leading to exposed wires or broken pigtails.

For a durable repair, clean the lamp housing, replace any damaged seals to prevent future moisture ingress, and use proper electrical connectors when joining wires. Regular inspection of rear lamps during service intervals helps catch socket degradation early and avoids driving with a non‑working rear light.

Lighting of the license plate (registration mark lighting) for the Citroën C1 and Peugeot 107. This is an original used part that replaces a damaged or oxidized lamp and restores the correct visibility and legal function of the Submitting of the Civil Code. With accurate OE codes 81270-020 and 6340E2, you can easily verify compatibility with your car.

The original design ensures the correct light scattering, weather resistance and trouble -free mounting into the original handles. Compared to universal substitutes, they sit exactly in the opening in the lid of the fifth door and use the original connector and seals.

The component is designed for the first generation Citroën C1 and Peugeot 107. On these cars are usually two same lamps above the registration sign – the left and right side are the same. They typically use the W5W (T10) 12 V 5 W in the base and two -meter electrical connection.

The replacement is fast and you can handle it without a jack: open the fifth door, carefully release the lamp latches and pull it out, disconnect the 2 -pin connector, transfer the W5W bulb (if right) into the new lamp, plug the connector and click the part back. After mounting, we recommend checking the function of both lamps and the condition of the seal.

Typical symptoms of defect: darkening or flashing of lighting, corrosion of contacts, cracked views or broken paws. It is often enough to replace the whole lamp – it is a faster and more reliable solution than repairing damaged brackets. For even appearance and light, both sides commonly change simultaneously.

technical information

• manufacturer: dog (Citroën/Peugeot); Cross OE Code Toyota
• Model: Citroën C1 I (2005–2014), Peugeot 107 (2005–2014)
• product codes: 6340e2 (PSA), 81270-0H020 (OE)
• Additional numbers: 6340.e2, 6340 E2, 812700H020

Mounting tip: Clean the bearing surface before clinging and check the seals so that it does not flow into the fifth door space. Use the right type (W5W/T10) and 5 W power for homologation and lifetime.

This high-mounted stop lamp with an integrated washer nozzle is a direct-fit replacement for many Citroën C1 and Peugeot 107 models (also fitted to Toyota Aygo). Supplied as a used unit, it restores brake-light visibility and rear-window washing functionality in a single component. Ideal for auto technicians and DIY enthusiasts looking for a cost-effective repair using original-style equipment. Search keywords: third brake light, high-mounted stop lamp, rear washer nozzle, 1606372780, 6351W4, Citroën C1 brake light, Peugeot 107 brake light.

Technical Information

• Manufacturer: Stellantis
• Model(s): Citroën C1, Peugeot 107, Toyota Aygo
• Product Codes: 1606372780, 6351W4
• Other Numbers: 1606372780

Function And Benefits

The unit combines the third brake light (high-mounted stop lamp) with a rear-window washer nozzle. It improves visibility to following traffic during braking and keeps the rear glass clear when the washer circuit is activated. Using an original-style component ensures correct fitment, alignment, and reliable operation with the vehicle wiring and washer tubing.

Installation Recommendations

Before starting the replacement, follow standard workshop safety procedures. Disconnect the battery or isolate the electrical system to avoid short circuits while working on lighting connectors. Typical replacement steps:

• Open the rear hatch and remove the interior trim panel to access the light assembly.
• Disconnect the electrical connector and the washer hose from the nozzle (have a small container ready for residual fluid).
• Remove the retaining screws or clips and extract the old unit from the hatch.
• Clean the mating surface thoroughly; remove old sealant and debris.
• Because this is a used unit with a non-sealing rubber gasket, apply a continuous bead of automotive-grade silicone sealant to the contact surface before fitting to ensure watertight installation.
• Refit the unit, reconnect the washer hose and electrical connector, secure all fasteners, then test the brake light and washer operation before reassembling the trim.

Why This Part Fails Most Often

Common failure causes include degraded or torn rubber gasket leading to water ingress, cracked or UV-damaged lens, impact damage from rear collisions, or blocked/faulty washer nozzle. Corrosion at the electrical connector or contamination of the washer hose can also impair function. In this specific unit the rubber sealing is compromised and requires resealing with silicone to prevent leaks.

Practical Tips

• Use a high-quality automotive silicone for sealing; allow recommended cure time before exposing to water.
• Inspect the washer hose and connector for cracks or brittleness while replacing the lamp—replace the hose if necessary.
• After installation, verify lamp illumination, washer nozzle spray pattern, and absence of leaks around the gasket during a wash cycle.

Looking for a reliable replacement part for your Peugeot 107 or Citroën C1? Our Right Rear Light for Peugeot 107, product code 6351X6, is the perfect solution for restoring your vehicle’s lighting system. This part is compatible not only with the Peugeot 107 but also with first-generation Citroën C1 models. Integrate this essential component into your vehicle’s body for safe driving in poorly lit conditions.

Technical Information:
Manufacturer: PSA CITROEN PEUGEOT
Model: Peugeot 107, Citroën C1
Product Codes: 6351X6
Other Numbers: Information not available

This replacement part is primarily designed for the rear of the vehicle and can be easily installed without the need for special tools. Rear lights are a critical element in ensuring your vehicle’s visibility, which can significantly reduce the risk of rear-end collisions, especially in nighttime and adverse weather conditions. As a used auto part, this part has undergone a thorough quality check to meet your expectations while ensuring your safety and comfort.

Customers in need of a reliable automotive parts supplier will appreciate our offer of the right rear light for Peugeot 107 with code 6351X6 for its accuracy and compatibility. Rely on a proven part that restores your vehicle’s original functionality and aesthetics. If you do not want to risk unreliable alternatives, choose our product that delivers the certainty and performance you need.

Are you looking for high-quality spare parts for your CITROËN C1 or PEUGEOT 107? The right reflector with part number 9659830580 is the ideal choice to restore the original appearance and functionality of your vehicle. This part has been carefully selected and verified to meet the highest standards of quality and reliability.

As a used part, the reflector offers a great alternative to expensive new parts, especially when seeking an effective solution for older car models. The reflector is specifically designed for CITROËN C1 and PEUGEOT 107 models, ensuring a perfect fit and functionality. Installation of this part is straightforward and can be handled by anyone with basic mechanical skills, saving on professional installation costs.

Technical Information:
Manufacturer: PSA
Model: Citroën C1, Peugeot 107
Product Codes: 9659830580, 6340E6
Additional Numbers: 9659830580

The reflector plays a crucial role in vehicle safety as it enhances visibility for other road users, especially under poor lighting conditions. Using original or high-quality replacement parts like this reflector will help keep your vehicle in a safe and functional state.

This specific used part has been carefully selected to provide optimal performance while maintaining an affordable price. If you need a reliable replacement part to keep your vehicle in good technical condition, this reflector is the right choice for you.

Looking for reliable parts for your Citroën C1 or Peugeot 107? Our online store offers the original left rear bumper reflector, ideal for both professional mechanics and DIY enthusiasts. This used replacement part ensures your vehicle looks like new while meeting all functional and aesthetic requirements.

This replacement part is particularly suitable for Citroën C1 and Peugeot 107, thanks to its perfect compatibility and original design. With us, you can be assured that you will receive a quality, provenance-verified part that has undergone thorough inspection and meets high standards for used components. The right part can restore your vehicle’s appearance to its original level of appeal and functionality.

Technical Information

• Manufacturer: CITROEN / PEUGEOT
• Model: CITROEN C1, PEUGEOT 107
• Product Codes: 9659830680, 6340E7
• Additional Numbers: The part is also identified by OEM numbers 9659830680 and 6340E7, ensuring seamless integration with your vehicle.

This part is often sought after for its specific role on the vehicle – protecting the body and enhancing the overall aesthetics of the car. It is important to mention that the reflector may require more frequent replacement, especially due to unintended collisions and wear from regular use. Replacing this part can be done independently using basic tools and does not require specialized technical knowledge, making it ideal for DIY repairs.

We offer quality used parts to help keep your vehicle in great condition without the need to invest in expensive new components. Keep your Citroën or Peugeot in shape with our range of auto parts that guarantee satisfaction and longevity.

Product Overview

This right-hand rear lamp (passenger side) is an original equipment part designed for Citroën C1 and commonly compatible with Peugeot 107. Supplied without bulb sockets, the unit replaces the complete rear light assembly and carries original part references for easy lookup: 81550-0H060 / 81550-060 / 6351X8. Ideal for professional workshops and experienced DIY mechanics who require a direct-fit OE solution.

Key Benefits

• Direct Replacement: Original part geometry and mounting points ensure a precise fit and straightforward installation.
• Durable Construction: Designed to OEM specifications for consistent light output and weather sealing.
• Quick Identification: Commonly searched by OE codes (81550-0H060, 81550-060, 6351X8) for fast part finding.
• Cost Effective Repair: Replacing the full lamp body restores appearance and safety after impact or water damage.

Compatibility

Designed for:

• Citroën C1 (rear, right / passenger side)
• Peugeot 107 (possible fit, verify physical match)

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1; Peugeot 107 (possible)
• Product Codes: 81550-0H060, 81550-060
• Additional Numbers: 6351X8

Function And Notes

The rear lamp assembly houses brake, tail and indicator lamp functions depending on bulb configuration. This listing is for the lamp body only and does not include bulb sockets or bulbs. Ensure the correct bulb types are installed and that electrical connectors are clean and intact to maintain reliable operation and road safety.

Replacement Procedure (General Guide)

1. Prepare Tools: Basic tools typically include a screwdriver set, trim removal tool and a 10 mm socket or appropriate screwdriver for tailgate/trim fasteners.
2. Safety First: Disconnect the battery before starting electrical work to prevent short circuits.
3. Remove Interior Trim: Access the rear lamp fasteners from inside the luggage compartment by removing the trim panel or covers.
4. Unbolt Lamp Assembly: Unscrew the retaining bolts and carefully pull the lamp away from the body to expose the electrical connector(s).
5. Disconnect Connector(s): Release the clip and unplug the wiring harness. Remove the old lamp assembly.
6. Fit New Lamp: Position the replacement lamp, reconnect the wiring harness and secure the assembly with original fasteners.
7. Test Functionality: Reconnect the battery and test all lamp functions (tail, brake, indicator, reverse if applicable) before reassembling interior trim.

Installation Recommendations

• Always Disconnect The Battery Before Starting Work To Avoid Short Circuits.
• Check Connectors For Corrosion And Bent Pins; Clean Or Replace As Necessary.
• Use Correct Torque On Mounting Bolts To Prevent Cracking Of Plastic Tabs.
• Seal Bodywork Edges If Water Ingress Is A Concern; Replace Gaskets Or Seals When Damaged.
• Verify Bulb Types And Fitment Since This Unit Is Supplied Without Bulb Sockets.

Most Common Failure Reasons

• Water Ingress: Damaged seals or cracked lens allow moisture into the lamp, causing corrosion of contacts and reduced lighting performance.
• Impact Damage: Rear collisions or minor bumps often crack the lens or break mounting tabs, requiring full assembly replacement.
• Connector Corrosion: Road salt and moisture corrode the electrical connector, leading to intermittent or lost function.
• Aging And UV Exposure: Long-term exposure can cause plastic fading, seal hardening and eventual leakage.

Final Notes

When ordering, refer to OE codes 81550-0H060 / 81550-060 / 6351X8 to improve search accuracy. This original lamp assembly restores factory fit and finish and is recommended when the lens or mounting points are compromised.