Left rear light for Citroën Berlingo and Peugeot Partner is an original part of the dog suitable as a direct replacement of a damaged lamp. It is a version for cars with two -leaf rear doors (not for the fifth door). It comes without the base of the bulbs – the existing socket can be easily transferred from the original light or purchased separately.

The original design ensures accurate attachment to factory holders, proper geometry and compatibility with the wiring of the car. This is crucial for the correct function of the brake light, rudder, end and back light and fog lighting on the left side.

Recommendations to verify compatibility: follow the OE codes 6350Z0 and 6350CX and the rear door type (double). If you are unsure, compare the numbers from the dismantled episode with the codes.

Typical reasons for replacing the rear lamp: mechanical damage to the cover (cracks after impact), leakage and subsequent corrosion of contacts, loss of clearness and visibility. Early replacement increases traffic safety and minimizes the risk of problems per MOT.

Fast replacement procedure: Open the rear door, remove the screws holding the lamp (usually 2-3 Torx head screws), carefully remove the light from the body, disconnect the connector, move the bulbs to the new lamp and plug everything back. After assembly, verify the function of all light circuits.

technical information

• Manufacturer: PSA (Citroën / Peugeot) – original part
• Model: Citroën Berlingo, Peugeot Partner; Double -winged door design; Location left (driver) side
• Product codes: 6350Z0, 6350CX
• Other numbers: 6350.z0, 6350.cx

Search keywords: left rear lamp Berlingo, left rear light partner, rear lamp Citroën/Peugeot, PSA 6350Z0, PSA 6350CX, for double doors, without base base.

The left headlight for the Citroën Berlingo II and Peugeot Partner II is an original part from Visteon, designed for accurate seating and correct light cone geometry. It is a halogen design with OEM codes 9644150980 and PSA 6204.AX, which facilitates rapid verification of compatibility and finding refund by part number. Ideal solution for replacement after accident, crashing glass or losing the clearness of the original light.

The part is used, the optics is slightly yellowish – a common phenomenon in older plastic headlights due to UV radiation. However, the condition corresponds to the operation and part is suitable for further use; For maximum luminosity, we recommend that you renovate/polish the cover glass before or shortly after it. The advantage of the original headlight is accurate compatibility with holders, connectors and the shape of the bumper and fender.

Compatibility typically includes the B9 model series (about 2008–2015, pre -phacelift). The surest is to compare the number of part 9644150980 and the dog 6204.AX with your original headlight and connector control. If the match sits, the headlight is suitable for mounting on the left (driver) side.

Frequent reasons for exchange in the following models: yellowing and matting of cover glass, cracks on stones or accidents, damage to the holders or leakage due to leakage. During the installation, pay attention to the correct fit in the body and seal, after installation always adjust the lights at the STK station or by means of the adjustment according to the service procedure to ensure optimal visibility and unlocation.

technical information

• Manufacturer: Visteon (OEM for PSA)
• Model: Citroën Berlingo II (B9), Peugeot Partner II (B9) – left headlight, halogen
• product codes: 9644150980; PSA 6204AX
• Additional numbers: 6204.AX; 6204 AX

Mounting tip: For these models, it is necessary to remove the upper mask for the removal of the headlight and release the upper part of the bumper to access the fastening points. Disconnect the battery before switching the connector and check the function, high beam and direction lights after assembly. Properly selected original part saves time at work and ensures a reliable result.

By choosing the original headlight used you get quality with accurate compatibility at a reasonable price. Thanks to the OEM design, you can rely on the right fit, smooth installation and safe light performance.

Original left headlight (left light, driver’s side) for Citroën Berlingo II and Peugeot Partner II. It is a used OEM part from a car with a raid about 38 000 km, in a very well -preserved condition – ideal for fast and quality repair after a small collision or replacement of tired light. Compared to cheap replacements, it offers accurate fit, the right light cone and long -term reliability.

You can easily verify compatibility according to the OEM codes. If they coincide with your original headlight, the shape of the connector and the handles fits. The left headlight is designed on the driver’s side. Before ordering, it is recommended to compare the numbers and photos with the disassembled work or verify according to the VIN.

Why it pays to the original light used: these models are the most common defects of cracked holders after impact, confusion of cover glass due to UV radiation or leakage. The well -preserved original headlamp is a better choice in terms of luminous intensity and lifetime than new, but poor secondary production.

Installation can handle an experienced car mechanic with conventional tools; For some versions, it may be necessary to enable or partially remove the front bumper to remove/insert the headlight. After installation, always adjust the slope of the lights as prescribed, ideally on the regloscope.

technical information
Manufacturer: Visteon / PSA
Model: Citroën Berlingo II (B9), Peugeot Partner II (B9) – left headlight
product codes: 9644150980, 6204AX
Other numbers: 6204.AX, 96 441 509 80, 6204 AX

The condition corresponds to the low raid – the headlight is clean and generally very well preserved (see the condition). It is an original part produced by the Visteon used by the PSA concern, which makes you sure the compatibility with the wiring of the vehicle.

Original right headlight for the Citroën Berlingo II and Peugeot Partner II from the manufacturer Visteon. Suitable as a substitute for damaged or foggy light. It is a used part with a slightly yellowish cover glass surface – fully functional for normal operation. The ideal choice for fast and accurate replacement thanks to the same handles and connectors as the original episode.

Location: Right front (passenger) – rh. It is recommended to verify compatibility according to codes 9644150880, 799980, 6205AW and visual comparison of the shape, handles and connector of your original headlight.

Why choose this episode

• Original PSA/OEM VISTEON – Precise Settlement and Proper Light Connection Geometry.
• Quick assembly without modifications – sits into the original holders and connects to the serial connector.
• Economic and functional replacement for a new headlamp.

tips for mounting

• Before work, it is recommended to disconnect the battery and protect the body paint at the point of manipulation.
• In these models, in most cases it is necessary to release or dismantle the front bumper to get to the headlight fastening screws.
• After replacement, check and possibly adjust the slope of the lights in accordance with the regulations to avoid dazzling other drivers.

status and appearance

• used part, slightly yellowish surface glass surface due to age and operation.
• can carry common signs of use (microodities, minor cosmetic defects), function is not affected.

technical information

• Manufacturer: Visteon
• Model: Citroën Berlingo II (B9, approx. 2008–2018), Peugeot Partner II (B9, approx.
• Product codes: 9644150880, 799980, 6205AW
• Other numbers: 6205.aw

Looking for the right headlight for Citroën Berlingo or Peugeot Partner? This original Visteon headlamp with codes 9644150880 /799980 / 6205AW is exactly what your Berlingo II or Partner II needs. Easy replacement, certainty of compatibility and better price/performance ratio compared to the new episode – all of this makes it a smart choice for car repair shops and home repairs.

This Left Rear Lamp is designed for Citroën Berlingo and Peugeot Partner vehicles from the M49 series, which feature a rear tailgate that opens upwards. The lamp is supplied without the socket, which can be purchased separately, including part of the wiring harness.

Citroën Berlingo and Peugeot Partner are multi-purpose vehicles produced since 1996 and remain in production today.

Production details include:
– First generation (M49) manufactured from 1996 to 2003, followed by the facelift (M59) from 2003 to 2009.
– Second generation (B9) produced between 2008 and 2012; the first facelift of the second series ran from 2012 to 2015, and the second facelift from 2015 to 2018.
– Third generation (K9) started production in 2018 and continues to the present.

Installation Instructions

To replace the lamp, unscrew the wing nut and gently slide the lamp towards you to remove it from its position.

Function and Durability

The rear lamp ensures optimal visibility and safety on the road by clearly signaling braking, reversing, and turning to other drivers. These lamps can fail over time due to exposure to weather, mechanical vibrations, or electrical issues, making periodic inspection and timely replacement important to maintain vehicle safety standards.

Manufacturer Details

This lamp is manufactured by Valeo, a leading French global automotive supplier headquartered in France and listed on the Paris Stock Exchange (CAC-40 index). Valeo offers a wide range of automotive products for original equipment manufacturers and the aftermarket, employing over 113,600 people across 33 countries.

Technical Information

• Manufacturer: Valeo
• Model: Citroën Berlingo, Peugeot Partner (M49 Series)
• Product Codes: 6350H2, 6350J1
• Additional Codes: 6350H2, 6350J1

Overview

This right rear tail light is a direct replacement designed for Citroën Berlingo and Peugeot Partner models equipped with a single rear door. It is ideal for professional workshops and DIY mechanics searching by product numbers 6351J1 or 6351H2. The unit restores full rear lighting functions including parking light, stop light, indicator and reversing lamp (depending on vehicle wiring) and helps maintain legal roadworthiness and safety.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën Berlingo I & II; Peugeot Partner I & II (vehicles with single rear door)
• Product Codes: 6351J1, 6351H2
• Other Numbers: 6351J1 | 6351H2

Installation Recommendations

Follow these general steps for safe and reliable replacement. Always observe manufacturer procedures and use appropriate tools.

• Park the vehicle on a level surface, switch off the ignition and remove the key.
• Open the rear door and remove the interior trim or access panel to reach the lamp fasteners. Use trim tools to avoid damaging clips.
• Unscrew the mounting bolts (typically accessible from inside the boot area) and carefully pull the lamp unit clear of the body.
• Disconnect the electrical connector and remove the lamp assembly.
• Fit the replacement lamp, reconnect the electrical connector and temporarily secure the unit.
• Test all light functions: tail/parking, brake, indicator and reverse (if applicable). Verify correct bulb/LED operation before final tightening.
• Secure all fasteners, replace the trim panel and check alignment and sealing to prevent moisture ingress.

Recommended tools: Socket set (commonly 8–10 mm), Phillips/Torx screwdriver, trim removal tools, gloves and dielectric grease for electrical connectors. For best results inspect the rear lamp sealing surface and replace damaged seals or clips.

Why This Part Fails Most Often

• Impact Damage: Rear collisions or minor knocks commonly crack the lens or deform the housing.
• Moisture Ingress: Damaged or hardened seals allow water to enter, causing corrosion, short circuits or fogging of the lens.
• Electrical Issues: Corroded connectors, wiring wear or blown fuses can mimic lamp failure.
• Bulb/Module Failure: Conventional bulbs burn out over time; integrated LED modules can fail due to thermal stress or moisture.
• Vibration And Aging: Long-term vibration can loosen fixings and damage solder joints or connectors.

Practical Tips For Mechanics And DIYers

When replacing a lamp, check the connector pins for corrosion and apply dielectric grease to improve contact longevity. Verify the vehicle fuse and wiring if a newly fitted lamp does not illuminate. Keep the sealing surfaces clean and ensure clips and screws are tightened evenly to maintain a watertight fit. Use the product codes 6351J1 and 6351H2 when searching to quickly locate the correct part.

This replacement tail light offers a straightforward way to restore rear lighting functionality on Citroën Berlingo and Peugeot Partner models with a single rear door — suitable for professional fitment or competent DIY installation.

This right rear tail light is designed specifically for Citroën Berlingo and Peugeot Partner vehicles from the M49 series with two rear doors. It is a direct replacement part that ensures proper illumination and enhances vehicle visibility, contributing to road safety.

The lamp is delivered without the socket, which can be purchased separately along with a section of the wiring harness for a complete installation. This flexibility allows for tailored repairs depending on your existing parts condition.

Function and Replacement

The rear tail light plays a critical role in signaling braking and turning intentions to other road users. Over time, tail lights can fail due to bulb burnout, water ingress, or physical damage from impacts. Regular checks and timely replacement maintain safety standards and compliance with traffic regulations.

Replacing the right rear tail light is straightforward: after removing the interior trim of the rear door, disconnect the wiring, remove the defective lamp, and install the new unit securely. Ensuring proper electrical connections and sealing is essential to prevent future malfunctions.

Technical Information

• Manufacturer: PSA
• Model: Citroën Berlingo, Peugeot Partner M49 Series (Two Rear Doors)
• Product Codes: 6351H1, 6351EC
• Additional Numbers: Not Applicable

Are you looking for reliable and quality auto parts for your Citroën or Peugeot vehicles? Our ceiling lamp for Citroën Berlingo and Peugeot Partner models is the perfect choice for anyone wanting to ensure proper interior lighting in their vehicle. This lamp, known by the code 6362K9, is a highly sought-after part among auto mechanics and enthusiasts who perform DIY car repairs.

Our ceiling lamp not only provides basic interior lighting but also offers easy installation, making it a practical and efficient addition to your vehicle. Although the functionality of the bulbs is not guaranteed, replacement is straightforward and can be done yourself without the need for a service visit. Reliability and long lifespan are key aspects that continuously attract Citroën and Peugeot drivers to this type of auto part.

Technical Information:
Manufacturer: PSA CITROEN PEUGEOT
Model: Citroën Berlingo, Peugeot Partner
Product Codes: 6362K9
Other Numbers: N/A

Buy with confidence second-hand spare parts that have undergone careful inspection and are ready for use in your vehicle. Provide your Citroën Berlingo or Peugeot Partner with the necessary light with our ceiling lamp, which is ready for installation. Order today and ensure your car is equipped with reliable parts for safe driving and comfort in illuminating lights.

This high-quality third brake light integrated with a wiring piece is an essential part for various models of Citroën and Peugeot vehicles. This car part from older models ensures better visibility of your vehicle while braking, which is crucial for your driving safety. Its proper functionality and installation are critical for adhering to safety regulations on the roads.

Installing this component on the rear double doors of CITROËN BERLINGO I, II and PEUGEOT PARTNER I, II is relatively easy, and the included wiring piece eliminates the need for any further electrical work. It should be noted that the functionality of the bulbs is not guaranteed; therefore, we recommend checking and possibly replacing the bulbs after installation.

Technical Information

• Manufacturer: PSA CITROËN PEUGEOT
• Model: CITROËN BERLINGO I, II | PEUGEOT PARTNER I, II
• Product Codes: 6350AS

This part is especially suitable for owners and garages specializing in these models and car brands. Customers who engage in their vehicle repairs will appreciate not only the wide compatibility of this brake light but also its ease of installation and instant enhancement of vehicle safety. Thanks to our direct sourcing and careful selection, we are able to offer this part in excellent condition and at very competitive prices.

Remember that any used part may require additional checks and maintenance. For maximum satisfaction, we recommend having the installation done by a professional mechanic. This ensures that your vehicle will be safe and functional throughout the use of the replacement part.

If you have any questions or need further information, please do not hesitate to contact us. Our team of specialists is here to assist you every step of the purchasing process and reintegration of the component into your vehicle.

Order the third brake light with wiring harness designed specifically for Citroën Berlingo I and II as well as Peugeot Partner I and II models. This component plays a crucial role in enhancing vehicle safety under low visibility conditions or heavy traffic by improving the visibility of the brake signal to other road users.

The part is mounted on the rear liftgate of the vehicle, making it easily accessible for maintenance or replacement. The replacement process is straightforward and can be performed by both DIY enthusiasts and professional mechanics within a short time.

Maintaining this light in good working condition is vital as it contributes significantly to the passive safety of your vehicle.

Please note that the functionality of the bulbs themselves is not guaranteed; we recommend checking and replacing them if necessary after installing this brake light.

Technical Information

Manufacturer: PSA Citroën Peugeot
Models: Citroën Berlingo I, II | Peugeot Partner I, II
Product Codes: 6350AP
Additional Numbers: Not available

This component offers an excellent solution for Citroën and Peugeot owners seeking a reliable, effective, and economical replacement for the original third brake light. Its compatibility with multiple models, combined with the included wiring harness, ensures convenience and functionality expected from quality auto parts.