Upgrade or replace the damaged right rear tail light on your Peugeot 607 with this genuine OEM lamp (code 6351N1). Designed for a direct fit into the rear wing (passenger side), this original assembly restores correct rear lighting, improves road safety and maintains factory appearance. Ideal for professional garages and DIY mechanics who search by part number (6351N1) to ensure fast, accurate replacement.

How This Part Works

The rear wing tail light assembly provides the rear position (tail), brake and turn signal lighting required for safe road use. The unit secures to the body flange on the passenger side and connects to the vehicle wiring harness via a multi-pin connector. This listing is for the lamp housing only and does not include bulb sockets or bulbs.

How To Replace

• Park the Vehicle On A Level Surface And Disconnect The Battery Before Starting Work.
• Access The Inner Wing Trim Through The Trunk/Boot And Remove Fasteners To Reach The Tail Light Mounting Bolts.
• Unscrew The Mounting Bolts, Carefully Unclip The Lamp From The Body, And Pull The Assembly Outwards.
• Unplug The Electrical Connector And Transfer Any Required Seals Or Gaskets To The New Unit.
• Install The New Tail Light Assembly, Tighten Mounting Bolts Evenly, Reconnect The Connector And Refit The Trim.
• Reconnect The Battery And Check All Functions (Tail, Brake, Indicator). Replace Bulb Sockets If Needed (See Additional Numbers).

Installation Recommendations

• Always Disconnect The Battery Before Removing Or Installing The Lamp To Avoid Short Circuits.
• Check And Replace Damaged Gaskets Or Seals To Prevent Water Ingress And Corrosion.
• Use Correct Fasteners And Moderate Torque To Avoid Distorting The Housing Or Body Flange.
• Test All Lighting Functions After Installation; Replace Bulb Sockets If Contacts Appear Corroded.
• For Replacement Bulb Sockets, Use Code 6534GS To Order The Correct Part.

Why This Part Commonly Fails

• Water Ingress: Cracked Lens Or Deteriorated Seals Allow Moisture To Enter, Causing Corrosion And Electrical Faults.
• Impact Damage: Rear Bodywork Collisions Often Break Or Misalign The Tail Light Assembly.
• Socket Or Connector Corrosion: Oxidation Of Electrical Contacts Causes Intermittent Lighting Or Failure.
• Ageing And UV Exposure: Prolonged Sunlight Can Fade Lenses And Weaken Plastic Mounting Tabs.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 607 (Executive Saloon)
• Product Codes: 6351N1
• Additional Numbers: 6534GS (Bulb Socket/Bearing Code)

Part Number 6351N1 Is A Common Search Term For Workshops And Enthusiasts Replacing The Right Rear Tail Light On Peugeot 607 Models. Keeping The Original Type Lamp Ensures Correct Light Output, Fitment And Finish.

Notes For Mechanics And DIYers

When servicing the rear lamp, Inspect The Wiring Harness For Chafing Or Previous Repair Splices. Replace Faulty Sockets (Code 6534GS) Rather Than Relying On Temporary Repairs To Avoid Recurring Faults. Proper Sealing During Reassembly Extends Service Life And Prevents Water-Related Failures.

This Original Equipment Taillight Is A Direct Replacement For The Left Rear Wing Of The Peugeot 607. Designed For Professional Workshops And Competent DIY Technicians, The Unit Restores Exterior Lighting Function And Appearance While Retaining OEM Fitment And Mounting Points. Commonly Searched By Part Number 6350N1, This Taillight Is A Practical Choice When Replacing A Damaged Or Waterlogged Rear Light Assembly.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 607
• Product Codes: 6350N1
• Additional Numbers: 6534GS (Bulb Holder Not Included)
• Side: Left Rear (Driver Side)
• Notes: Original Genuine Part, Bulb Sockets Not Supplied

Fitment And Compatibility

Fits Peugeot 607. Check Visual Match With Existing Unit Before Installation. This Assembly Replaces The Exterior Taillight On The Left Rear Wing And Uses The Same Mounting Points As The Original Factory Part. Because This Item Is Frequently Located By Its Part Number, Searches For 6350N1 Or 6534GS Will Help Locate The Correct Component Quickly.

Installation Recommendations

Turn Off Ignition Before Work And Park The Vehicle On Level Ground. Access The Taillight From The Rear Cargo Area Or Inner Wheel Arch Depending On Body Style: Remove Interior Trim Or Wheel Arch Liner To Reach Fasteners, Unscrew Mounting Bolts, And Carefully Disconnect The Electrical Connector. Remove The Old Unit, Clean Mounting Surface And Seal, Fit The New Taillight Ensuring Proper Alignment, Reinstall Fasteners To Manufacturer Torque Settings, Reconnect Electrical Connector, And Test All Light Functions (Brake, Indicator, Tail, Reverse Where Applicable). If The Bulb Holder Is Required, Order Under Code 6534GS And Install Bulbs Before Final Mounting. Protect Painted Surfaces During Removal And Refit Any Seals Or Gaskets To Prevent Water Ingress.

Most Common Failure Reasons

Taillight Failures On Peugeot 607 Are Typically Caused By Water Ingress Through Deteriorated Seals, Impact Damage From Minor Collisions, Cracked Or Clouded Lenses From Age And UV Exposure, And Corroded Electrical Contacts Or Bulb Holders. Condensation Inside The Lens Often Indicates A Compromised Seal; If Left Unchecked, Corrosion Can Damage The Connector And Bulb Sockets. Regular Inspection After Bodywork Or Minor Impacts Helps Prevent Unexpected Failures.

Practical Tips

• Always Compare The New Unit With The Old One For Mounting Hole Positions And Connector Type Before Final Fitment.
• Replace Seals Or Gaskets When Installing To Ensure Long-Term Water Tightness.
• Use Quality Replacement Bulbs And Clean Electrical Contacts To Avoid Flicker Or Poor Contact.
• If The Lens Is Scratched But The Housing Is Intact, Consider Lens Polishing Only As A Temporary Measure; Full Replacement Gives Best Long-Term Results.

Warranty And Quality

This Is An Original Equipment Component Intended To Meet Factory Specifications For Fit And Finish. For Professional Results, Follow Standard Workshop Procedures And Torque Recommendations During Installation.

Product Overview

Replace damaged or worn rear lighting with this original left rear tail light for the tailgate of the Peugeot 607. Manufactured to OEM specification, this unit restores the factory appearance and lighting functions at the back of the vehicle. It is the driver’s side lamp and is supplied without bulb sockets—bulb holders can be ordered separately under code 6534GT. Frequently Searched As Part Number 6350N2.

Fitment And Function

Designed for Peugeot 607 models with a tailgate rear lamp arrangement. The assembly serves as a rear combination lamp for the tailgate and, depending on vehicle equipment, covers tail/position light, stop light and indicator functions. Confirm fitment for specific model years and trim levels when matching mounting points and connector types.

Installation Recommendations

• Open The Tailgate And Remove The Interior Trim Panel To Access The Lamp Fasteners.
• Unscrew Or Unbolt The Retaining Fixings And Carefully Disconnect The Electrical Connector.
• Remove The Old Lamp Assembly, Fit The New Unit And Reconnect The Wiring Harness Securely.
• Install Bulb Sockets And Bulbs If Required (Bulb Socket Code: 6534GT). Test All Light Functions Before Reassembling The Trim.
• Inspect And Clean Sealing Surfaces; Replace Seals If Damaged To Prevent Water Ingress.
• When Working On Vehicle Electrical Systems, Take Standard Safety Precautions And Isolate The Circuit If Necessary.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 607
• Product Codes: 6350N2
• Additional Numbers: 6534GT (Bulb Socket)

Most Common Failure Reasons

• Physical Damage From Minor Collisions Or Impacts To The Tailgate Area.
• Water Ingress Or Condensation Due To Failed Seals, Causing Corrosion Of Contacts Or Internal Fogging.
• Cracked Lens Or Broken Mounting Tabs From Age, Vibration Or Improper Removal/Installation.
• Electrical Contact Corrosion Between Connector And Socket Leading To Intermittent Or Non-Functional Lights.

Why Choose This Part

This original replacement tail light offers direct fitment and visual match with factory components, making it a suitable choice for professional workshops and DIY mechanics seeking accurate repairs. Stocked under the commonly used part number 6350N2, it is easy to find and order for timely repairs.

Final Notes

Order The Correct Bulb Sockets Separately (Code 6534GT) And Verify Mounting Hardware During Installation. Replace Seals And Check Connectors To Ensure Long-Term Reliability And Prevent Recurring Issues.

Overview

High-quality replacement right rear tail light designed for the tailgate of the Peugeot 607. This original-style unit restores rear lighting functions including tail/position, brake and indicator (function depends on vehicle wiring and bulb configuration). Ideal for professional garages and DIY mechanics looking for a direct-fit part identified by product code 6351N2.

Benefits

• Direct Fit For Peugeot 607 Tailgate—Easy Replacement To Restore Exterior Lighting And Safety.
• Original-Style Construction For Correct Shape, Mounting Points And Optical Performance.
• Part Number Search Friendly: Frequently Found Under Code 6351N2.
• Bulb Holder Not Included—Option To Order Separately Under Code 6534GT.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Peugeot 607
• Product Codes: 6351N2
• Additional Numbers: 6534GT (Bulb Holder)

Compatibility

This unit Is Intended For The Right Side (Passenger Side) Tailgate Of The Peugeot 607. Confirm Fitment By Matching The Part Number 6351N2 With Your Existing Unit.

Replacement Procedure

Basic Steps For Replacement (General Guide For Experienced Mechanics And Competent DIYers):

• Disconnect The Battery Before Starting Work To Avoid Short Circuits Or Damage.
• Open The Tailgate And Remove Interior Trim Panels To Access The Light Mounting Screws.
• Unscrew The Mounting Fasteners And Carefully Pull The Light Assembly Out Of The Tailgate.
• Unplug The Electrical Connector And Remove The Bulb Holder If Present (Note: This Unit Is Supplied Without Bulb Holder; Order Code 6534GT If Required).
• Fit The New Assembly, Reconnect The Electrical Connector, And Secure The Mounting Screws.
• Reconnect The Battery And Verify All Light Functions (Tail, Brake, Indicator, Reverse As Applicable).
• Refit The Interior Trim Panels And Check Seals To Prevent Water Ingress.

Mounting Recommendations

• Use Correct Tools And Appropriate Torque For Fasteners To Avoid Cracking The Lens Or Stripping Threads.
• Replace The Bulb Holder If It Shows Signs Of Corrosion Or Wear; The Assembly Is Supplied Without The Holder.
• Inspect Seals And Gaskets; Replace Damaged Seals To Prevent Moisture Entry.
• Test All Functions After Installation And Ensure Proper Alignment To Avoid Reduced Visibility.

Why This Part Fails Most Often

Common Causes Of Failure Include:

• Impact Damage From Minor Collisions Or Loading/Unloading The Tailgate.
• Water Ingress Due To Worn Seals Or Cracked Lens, Leading To Corrosion Or Electrical Faults.
• Connector Or Bulb Socket Corrosion Resulting In Intermittent Contact.
• Aging And UV Degradation Of The Lens Causing Cracks Or Clouding.
• Burnt Bulbs Or Faulty Wiring (Note: Bulbs And Bulb Holder May Need Separate Replacement).

Notes

Part Number 6351N2 Is The Primary Identifier For This Right Rear Tail Light. Bulb Holder Is Not Included; Use Code 6534GT If A Replacement Holder Is Required. Suitable For Professional Workshops And Knowledgeable DIY Enthusiasts.

This nozzle plays a significant role in ensuring your headlights remain clean and free from dirt, improving visibility during adverse weather conditions. It efficiently sprays cleaning fluid onto the headlight, providing a clear view of the road ahead. Regular use helps maintain safe driving conditions, especially during rain or snow.

Replacement of the washer nozzle is straightforward, making it an ideal choice for both professional mechanics and DIY enthusiasts. It’s recommended to check the condition of the nozzle periodically, as wear and tear can lead to decreased performance over time.

Technical Information:

• Manufacturer: Citroën, Peugeot
• Model: 307 I and II, 607, C5 I, C8, 807
• Product Codes: 6438F5
• Other Numbers: 6438F5

Compatible Models: This nozzle fits various models including the Citroën 307 I and II, 607, C5 I, C8, and 807, making it a versatile choice for both professional mechanics and DIY enthusiasts.

Installation: The installation process is straightforward and can be done with basic tools. Typically, the old washer nozzle can be removed by disconnecting the water line and prying it out. The new nozzle should be simply pushed into place and reconnected.

Function: The primary function of the washer nozzle is to spray windshield washer fluid onto the headlights, ensuring they are clean and enhancing overall visibility. Over time, nozzles may become clogged or damaged, often due to debris or freezing temperatures, making it essential to replace them to maintain vehicle safety.

Technical Information

• Manufacturer: PSA Group
• Model: Citroën Peugeot
• Product Codes: 6438F4
• Additional Numbers: N/A

Overview

Direct-fit right front Xenon headlight assembly designed for Peugeot 607 applications. This complete unit is ideal for professional workshops and experienced DIYers who require a ready-to-install headlamp with all exterior mounting points preserved. The assembly is supplied as a full headlight unit, making replacement fast and reducing the need for additional parts.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 607
• Product Codes: 89004892, 620659
• Additional Numbers: 620659 | 89004892

Compatibility & Fitment

Fits Right Front (Passenger Side) of Peugeot 607 models that use the factory Xenon lighting system. Check the unit’s connectors and mounting points visually against the vehicle before installation to confirm compatibility with your specific model year and trim.

Installation Recommendations

• Always Disconnect The Battery Before Starting Work. This Reduces The Risk Of Electrical Damage And Airbag System Interference.
• Remove Any Trim Panels Or Covers That Block Access To The Headlight Fasteners. Typical Procedure: Open Bonnet, Remove Relevant Covers, Undo Mounting Bolts, Unplug Electrical Connectors, And Extract The Assembly.
• When Installing, Ensure Correct Alignment Of Mounting Tabs And Torque Fasteners To Manufacturer Specifications To Avoid Stressing Brackets.
• After Fitment, Check Headlight Aim And Leveling. Xenon Units Require Proper Aim To Meet Road Safety Standards And Avoid Glare.
• Inspect Electrical Connectors And Headlight Washer/Leveling Connections If Present. Replace Any Damaged Seals To Prevent Moisture Ingress.

Why This Part Fails Most Often

• Water Ingress And Condensation Causing Corrosion Or Short Circuits In Bulb Sockets, Ballasts, Or Connectors.
• Impact Damage From Minor Collisions That Break Mounting Tabs Or Distort The Housing.
• Failure Of The Xenon Ballast Or Igniter, Which Can Cause Intermittent Operation Or Complete Loss Of Light.
• Bulb End-Of-Life. Xenon Lamps Typically Have A Service Life Measured In Thousands Of Hours; Dimming Or Flicker Indicates Replacement.
• Heat-Related Degradation Of Seals And Reflective Coatings Over Time, Leading To Reduced Light Output.

Practical Notes

This Assembly Is Supplied Complete And Was Described As Fully Functional With All Brackets Intact. On Xenon Systems, Confirm That The Ballast And Connectors Match Your Vehicle Harness. After Installation, Verify Automatic Leveling And Washer Functions If The Vehicle Is So Equipped.

Why Choose This Unit

Professionally Suitable For Workshops And Skilled DIYers Who Need A Reliable, Direct-Fit Right Front Xenon Headlight For Their Peugeot 607. Having The Complete Housing With Intact Mounts Reduces Installation Time And Additional Repair Costs.

Additional Information

Product Codes And Tags Included In The Listing: 89004892, 620659. Use These Numbers When Searching For Compatibility Or Cross-Referencing With Other Parts Catalogs.

Warranty & Condition

Described As A Complete, Undamaged Unit That Was Tested For Functionality. Please Note Condition Details Provided In The Listing Before Purchase.

Washer Nozzle Holder Citroën Peugeot 6438F3, 89028244, 89033643

The Washer Nozzle Holder, identified by the part numbers 6438F3, 89028244, and 89033643, is an indispensable part of the washer assembly that guarantees firm mounting and proper operation of the spray nozzles.

Technical Information:

• Manufacturer: Citroën Peugeot
• Model: Compatible with various Citroën and Peugeot models.
• Product Codes: 6438F3, 89028244, 89033643
• Additional Numbers: 6438P1

Function:

The Washer Nozzle Holder serves to securely mount the nozzle on the hood or other parts of the vehicle, ensuring stable and efficient spraying of washer fluid onto the windshield. Properly positioned and functional nozzles are crucial for maintaining glass cleanliness and ensuring good visibility in all weather conditions.

Advantages:

• Reliability: High-quality materials and construction guarantee long-term and trouble-free operation.
• Easy Installation: Designed for easy installation with precise design ensuring compatibility with original nozzles.
• Durability: Material resistant to weather and chemicals found in washer fluid.

Installation:

When replacing or installing the washer nozzle holder, it is essential to ensure proper mounting and placement to guarantee the correct functioning of the washer system. It is recommended to perform the installation at an authorized service center or with the help of a qualified technician to ensure optimal functionality and safety of the washer system.

Recommendations:

To maintain optimal performance and reliability of the washer system, it is advisable to use original replacement parts or those from reputable manufacturers. Original parts ensure compatibility and long-term reliability, which is crucial for the safe and efficient operation of the vehicle.

This nozzle is specifically for the right side, located next to the passenger seat, and it is an essential component for maintaining clear headlights by effectively cleaning them during inclement weather.

It is common for washer nozzles to fail due to clogs, corrosion, or general wear and tear over time, leading to reduced visibility when driving. Replacing a malfunctioning nozzle will enhance safety by ensuring that the headlights are clean and functioning properly.

Replacing the headlight washer nozzle is a straightforward process that typically involves removing the old nozzle and simply clicking the new one into place. It’s recommended to check and replace this part as needed, especially if you notice that your headlights are not being adequately cleaned.

Technical Information

• Manufacturer: PSA
• Model: Peugeot 607
• Product Codes: 6438F5, 6438F3, 6438F6
• Additional Numbers: N/A

This high-quality wiring harness is crucial for the proper functioning of your tail lights, which significantly contribute to road safety by ensuring visibility. Wiring harnesses like this one can often fail due to wear and tear, exposure to extreme weather conditions, or electrical faults, leading to poor lighting and safety hazards. Regular inspection and timely replacement of faulty wiring harnesses are recommended to maintain optimal performance.

Technical Information

• Manufacturer: PSA
• Model: 607
• Product Codes: 6534GT
• Additional Numbers: NFP