Product Overview

High-mounted stop lamp designed for Peugeot 307 hatchback models. This central third brake light (part number 6350P5) restores clearly visible braking indication at the rear of the vehicle and helps maintain legal road safety standards. Ideal for professional workshops and competent DIY mechanics who need a direct-fit replacement that is easy to identify by OEM code 6350P5.

Key Benefits

• Direct replacement for the original high-mounted stop lamp—fits the tailgate aperture without modification.
• Part number searchable (6350P5) for quick identification in parts catalogs and online searches.
• Improves rear visibility and ensures compliance with brake light regulations.
• Simple plug-and-play electrical connection for most standard units—reduces workshop time.

Technical Information

• Manufacturer: Peugeot (Stellantis)
• Model: Peugeot 307 Hatchback
• Product Codes: 6350P5
• Additional Numbers: Not specified

Typical Function And Failure Modes

The third brake light serves as a high-mounted stop lamp that provides a clear signal to following traffic when the driver applies the brakes. Common failure causes include bulb burnout (where applicable), LED module failure on later production units, water ingress and corrosion of contacts, damaged wiring or connector problems due to wear or impact, and physical damage from tailgate collisions. Regular visual inspection and ensuring seals and connectors are intact will extend the service life.

Replacement Interval

There is no fixed interval for replacing the high-mounted stop lamp; replacement is usually carried out when the lamp fails, shows intermittent operation, or the lens/assembly is physically damaged. In typical conditions, incandescent bulbs may last several years, while LED modules generally deliver longer service life but are more sensitive to electrical faults and water ingress.

Installation Recommendations

Recommended for experienced mechanics or competent DIYers. Basic replacement steps:

1. Open the tailgate and remove the internal trim panel to access the lamp housing.
2. Unscrew the fasteners securing the third brake light assembly (retain screws for reuse if undamaged).
3. Disconnect the electrical connector carefully—avoid pulling on wires.
4. Remove the old assembly and fit the new unit into the tailgate aperture, aligning clips or screw holes.
5. Reconnect the connector and test the brake light operation (apply brake pedal or have an assistant operate the brake while you observe).
6. Reinstall the trim panel and verify that all fasteners and seals are correctly seated to prevent water ingress.

Always follow vehicle manufacturer guidance for access and fastening torque where provided. Before starting work, isolate the electrical system according to safe working practices (e.g., park vehicle, ignition off). Avoid forcing connectors or overtightening fasteners to prevent damage.

Why This Part Most Commonly Fails

Failures are most often due to bulb burnout (on non-LED versions), moisture penetration causing corrosion of contacts or internal circuitry, impact damage to the tailgate area, or wiring/connector fatigue from repeated tailgate movement. Poor sealing after previous repairs can accelerate failures via condensation and corrosion.

Buying Advice

When searching or ordering, use the part code 6350P5 to locate the correct third brake light for Peugeot 307 hatchback. Choose quality replacement units and check the condition of connectors and tailgate seals during installation to avoid early re-failure. Suitable for workshop replacement and for skilled DIY repairers looking for a reliable, direct-fit solution.

This left rear tail lamp is a direct-fit replacement for the PEUGEOT 307 SW (estate) up to 2005 and is ideal for professional workshops and DIY mechanics who need a reliable, correctly fitting lamp. Supplied without bulb holders, it allows flexible installation when you already have functional sockets or prefer to install new holders separately. The part is commonly searched under the product code 6350Q6, so use that reference when locating the correct item for your vehicle.

Benefits And Fitment

Designed to match OE mounting points and contours, this lamp restores correct exterior lighting function and appearance. It provides clear signalling for brake, tail and indicator functions (bulbs and holders not included). Ideal for collision repairs, corrosion-damaged assemblies or when lens cracking lets moisture in. Robust housing and lens geometry ensure correct light dispersion and a factory-like finish after replacement.

Installation

1. Open the tailgate and remove any interior trim panels covering the lamp mounting area.
2. Unscrew the retaining bolts/nuts securing the lamp assembly (typically accessible from inside the boot).
3. Carefully pull the lamp unit out enough to reach the electrical connector and unplug it.
4. If present, remove old bulb holders/sockets from the lamp and transfer or replace bulbs as required (this unit is supplied without holders).
5. Position the new lamp into the body flange, align the mounting points and fasten the retaining bolts/nuts securely.
6. Reconnect the electrical connector and test all lamp functions (tail, brake, indicator, reverse if applicable).
7. Refit the interior trim and close the tailgate. Check gaps and alignment for a uniform finish.

Installation Recommendations

Always disconnect the vehicle battery before starting to avoid short circuits. Handle the lens and housing carefully to avoid scratches. Clean and inspect connectors and wiring for corrosion; apply dielectric grease to contacts to improve conductivity and future corrosion resistance. Replace damaged gaskets or seals to prevent water ingress. After installation, verify correct operation of all lamp functions and adjust alignment if necessary.

Why This Part Most Commonly Fails

• Impact Damage: Rear-end collisions and minor knocks easily crack lenses or break mounting tabs.
• Water Ingress: Damaged seals or cracked lenses let moisture into the assembly, causing condensation and electrical faults.
• Connector And Socket Corrosion: Exposure to road salt and moisture corrodes contacts and bulb holders, causing intermittent or failed lighting circuits.
• Plastic Fatigue: Aging and UV exposure can make mounting points brittle, leading to broken tabs and poor fitment.

Technical Information

• Manufacturer: PEUGEOT / Stellantis
• Model: Peugeot 307 SW (Estate), Left Rear, Up To 2005
• Product Codes: 6350Q6
• Other Numbers: NFP (as listed)

Practical Notes

This lamp is a practical choice for technicians and independent mechanics restoring rear lighting on the Peugeot 307 SW. Because the unit is supplied without bulb holders, verify the correct bulb types and holders required for your vehicle before fitting. After replacement, always test brake, tail and indicator lights from outside the vehicle and with an assistant if possible to ensure full functionality and safety compliance.

Product Overview

High-quality left rear inner lamp designed for the tailgate (driver side) of the Peugeot 307 CC. This unit is often sought by professional mechanics and DIY enthusiasts by its product codes 96413007JE, 714025600701 or 6350S4. The lamp has been carefully resealed with silicone to prevent condensation and to secure the lens. Note the visible lightening/discoloration of the lens that can develop over long service life.

Why Buy

Ideal replacement for damaged, leaking or faded tailgate lamps. Fits the original mounting points and wiring plugs, making it suitable for quick workshop or home repairs. The resealing reduces the risk of fogging and internal moisture, improving reliability of the electrical contacts and bulbs.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 307 CC
• Product Codes: 96413007JE, 714025600701, 6350S4
• Additional Numbers: 6350S4, 714025600701, 96413007JE

Function and Common Failures

This unit serves as the rear lamp assembly located in the tailgate, providing rear illumination functions depending on vehicle equipment. Common reasons for replacement include seal deterioration leading to water ingress, UV exposure or aging causing the lens to lighten or discolor, physical damage from impacts, and corrosion or failure of sockets and electrical contacts.

Replacement Frequency

There is no fixed interval for replacement. Lamp housings typically remain serviceable for many years, but environmental exposure (moisture, road salt, UV) and mechanical damage reduce service life. If the lens has become significantly lightened, cracked, or allows moisture inside, replacement is recommended to ensure visibility and proper operation.

Installation Recommendations

• Work Safely: Park on level ground and isolate the vehicle electrical system where appropriate before disconnecting wiring.
• Access: Open the tailgate and remove interior trim panels to reach fasteners and wiring of the tailgate lamp.
• Removal: Unplug the wiring connector, remove retaining screws or clips, and carefully extract the old lamp from its housing.
• Inspection: Check mounting points, wiring harness, bulb holders and earthing surfaces for corrosion or damage. Replace bulbs or socket clips if corroded.
• Sealing: Ensure the mating surface is clean and dry. If resealing is necessary, use automotive-grade silicone or sealant compatible with lamp materials to prevent future fogging.
• Fitment: Align the replacement lamp to original mounting points, tighten fasteners to secure the unit, reconnect the wiring and test all light functions (tail, brake, indicator, reverse as applicable).
• Final Check: Refit interior trim and verify there is no vibration or movement of the lamp when closing the tailgate.

Why This Part Fails Most Often

The most common causes of failure are seal degradation and subsequent water ingress, and long-term UV exposure that lightens or discolors the lens. Mechanical impacts and corrosion of bulb sockets or connectors also account for many replacements. Resealing the unit and ensuring dry, clean mounting surfaces slows recurrence of these issues.

Search Keywords: Peugeot 307 CC left rear lamp, tailgate lamp 96413007JE, 714025600701, 6350S4, rear light Peugeot 307 CC, driver side tailgate lamp.

This rear right tail lamp is a direct replacement option for the Peugeot 307 CC passenger side. It is an ideal choice for professional workshops and DIY mechanics looking for a reliable, ready-to-fit unit. The assembly is resealed to prevent moisture ingress, reducing the chance of internal fogging and loosening of the outer lens. Customers often find this part by entering product codes such as 714025600861, 6351X4 or 6351S3 in search engines or parts catalogs, so these references are included for quick identification.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307 CC
• Product Codes: 714025600861, 6351X4, 6351S3
• Additional Numbers: 714025600861 | 6351X4 | 6351S3

Compatibility

Designed for the rear right (passenger side) of the Peugeot 307 CC (Coupe-Cabriolet) models. Verify visual fitment and connector type before installation if the vehicle has been modified or fitted with non-standard equipment.

Installation Recommendations

• Park the vehicle on a level surface and disconnect the negative battery terminal before work to avoid electrical shorting.
• Access the lamp from the trunk/boot side by removing interior trim panels to reach the mounting screws and electrical connector.
• Unscrew the mounting fasteners, unplug the wiring harness, and remove the old lamp assembly. Inspect the wiring and socket for corrosion and repair if needed.
• Fit the replacement lamp, reconnect the harness, and secure the mounting screws evenly to ensure correct alignment and sealing.
• Test All Light Functions (tail, brake, indicator and reverse where applicable) before refitting trim. If necessary, replace bulbs or clean contacts for reliable operation.
• Ensure the external sealing surface is clean and free of grease. Although this unit is resealed, check the gasket and apply an approved automotive sealant only if a gap or damage is visible.

Most Common Failure Reasons

• Moisture Ingress: Failed seals or damaged lens allow water to enter, causing fogging, corrosion of bulb sockets and electrical faults.
• Impact Damage: Bumps or minor collisions can crack the plexiglass or deform mounting points, compromising seal and alignment.
• Electrical Issues: Corroded connectors, worn bulb contacts or wiring damage can lead to intermittent or complete failure of light functions.
• Aging Materials: UV exposure and temperature cycling over time can weaken plastics and gaskets, increasing the risk of leaks and lens clouding.

Searchable by part numbers 714025600861, 6351X4 and 6351S3 — this taillight is supplied resealed to minimize moisture problems and provide a long-lasting fit for Peugeot 307 CC rear-right replacements. Ideal for professional fitters and skilled DIY mechanics who require a straightforward, reliable replacement part.

This rear left tail lamp is intended for Peugeot 307 CC vehicles and carries original Stellantis/Peugeot part references. The unit has been professionally resealed with silicone to prevent moisture ingress, so the lens remains clear and the plexiglass is securely fixed. Ideal for mechanics and DIY enthusiasts looking for a direct-fit replacement by part number (714025600761 / 6350S3 / 6350X4). Note: The lens has lightened over time on this used unit; a new example is shown in the second photo.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307 CC (Compatible with 307 Phase 1 and Phase 2 variants where applicable)
• Product Codes: 714025600761, 6350S3, 6350X4
• Other Numbers: 6350S3 | 6350X4 | 714025600761

Function And Features

Provides rear lighting functions including tail, stop and indicator (depending on vehicle wiring). The housing is supplied ready to fit with original mounting points and electrical connector. Resealed silicone bead reduces risk of condensation and water ingress, improving long-term reliability of the unit.

Installation Recommendation

General Replacement Steps:

• Disconnect the battery before starting any work on the lighting circuit.
• Access the lamp from the boot or inner wheel-arch by removing the trim or access cover.
• Unscrew the retaining bolts, carefully pull the lamp assembly out and disconnect the electrical connector.
• Fit the replacement lamp, reconnect the connector and test all lighting functions (tail, brake, indicator, reverse if applicable).
• Check sealing surfaces for cleanliness and apply additional silicone sealant if necessary to ensure watertight fitment.
• Refit trims and torque fasteners to manufacturer specifications where available.

Use proper tools, protect the painted surfaces and avoid scratching the lens during installation. Replace bulbs or socket inserts if signs of corrosion or wear are present.

Most Common Failure Reasons

• UV Exposure And Lens Fading: Prolonged sunlight can lighten or yellow the lens over time.
• Sealing Damage: Cracked or degraded seals allow moisture, causing fogging or electrical faults.
• Impact Damage: Rear collisions or stone chips can crack the lens or housing.
• Corroded Contacts Or Bulb Holders: Moisture or salt leads to poor electrical contact and intermittent function.
• Wiring Harness Damage: Chafing or connector damage from previous repairs or accidents.

Notes For Buyers

This lamp is commonly searched and ordered by its part numbers (714025600761, 6350S3, 6350X4). It is supplied resealed to prevent condensation; however, inspect mounting tabs and connector condition during fitment. Replace bulbs or connectors if necessary to ensure reliable operation.

Overview

High-mounted rear center brake light designed for Peugeot 307 Estate/Combi (SW) models. This unit improves rear visibility for following traffic and integrates the washer nozzle area. The lens may show a slight hairline crack around the washer aperture, which is a common cosmetic issue and does not affect sealing or operation.

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 307 I & II Estate / Combi / SW
• Product Codes: 6350Q2
• Other Numbers: N/A

Application And Fitment

Fits Peugeot 307 Estate variants (often referenced as Combi or SW) across first and second generation body styles where the high-level stop lamp with integrated washer is used. Commonly sought by mechanics and DIYers under the product code 6350Q2.

Function And Typical Faults

The third brake light provides a centrally positioned, high-mounted stop signal to increase visibility and reduce rear-end collisions. Typical failure modes include bulb or LED element burnout, connector corrosion, damage from impacts or tailgate misalignment, and water ingress if seals are compromised. In this specific unit a slight hairline crack near the washer area is present but the assembly remains fully sealed and resistant to fogging.

Replacement Procedure

• Open the tailgate and remove the interior trim panel to access the lamp assembly.
• Unscrew or unclip the mounting fasteners securing the lamp; keep track of clips and screws.
• Carefully unplug the electrical connector and release any washer hose if applicable.
• Remove the old unit and install the new lamp, ensuring the sealing surface is clean and the washer nozzle is correctly positioned.
• Reconnect the electrical connector, reattach the trim panel and test the brake light and washer function before finishing.

Installation Recommendations

• Disconnect the battery or isolate the circuit before starting work to avoid short circuits when handling electrical connectors.
• Handle the lens and connector gently to avoid damaging seals or wiring; inspect the wiring harness and connector for corrosion and clean as necessary.
• Ensure the mating surfaces are free of dirt and old sealant to maintain the unit’s watertight properties.
• Test operation of the brake light and washer after installation and confirm proper sealing by checking for water entry after a wash or light spray.

Why This Part Typically Fails

Third brake lights most commonly fail due to impact damage from tailgate closings, minor collisions, or stress around the washer aperture. Over time, seals can degrade and allow moisture into the unit, causing corrosion or LED/bulb failure. Connector corrosion and wiring wear are frequent causes in higher-mileage vehicles.

Notes For Buyers

Search keywords that increase findability: Peugeot 307 third brake light, rear center brake light 6350Q2, 307 SW brake lamp, high-mounted stop lamp Peugeot. The product code 6350Q2 is commonly used by mechanics when sourcing this part.

This left rear lamp is a direct replacement for Peugeot 307 SW estate models from 2005 onwards. Designed for professional workshops and DIY mechanics, the unit restores rear lighting functions and original appearance after damage or wear. Commonly searched under product codes 6350X3 and 6350X2, this lamp is a straightforward fit for the driver side (left) tail panel and is ideal when the original housing is cracked, faded, or water-damaged.

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 307 SW (Estate) – From 2005
• Product Codes: 6350X3, 6350X2
• Additional Numbers: None Specified

Functions

The rear lamp provides the vehicle’s rear lighting functions for the left side, including tail light and brake light circuits and the turn signal/reversing light positions depending on the vehicle wiring and bulb configuration. Because this unit is supplied without bulb sockets, fitment of the correct sockets and bulbs is required to restore full functionality.

Compatibility And Fitment Notes

Intended For Peugeot 307 SW Estate Models From 2005. Confirm Fitment By Matching Product Codes 6350X3 Or 6350X2 On Existing Unit. This lamp is Built To Replace The Left (Driver’s) Rear Combination Lamp And Matches Factory Mounting Points.

Replacement Procedure

1. Open Tailgate And Remove Interior Trim Panel To Access Rear Lamp Fasteners.
2. Unscrew Fasteners (Typical Tools: Phillips/Flat Screwdriver, Torx Or 10 Mm Socket Depending On Model) And Carefully Pull Lamp Assembly Outwards.
3. Disconnect Electrical Connector(s) And Remove Old Lamp.
4. If Required, Install New Bulb Holders And Bulbs Into The New Lamp Housing.
5. Reconnect Wiring, Fit Lamp Into Body Aperture And Tighten Fasteners Securely.
6. Test All Functions (Tail, Brake, Indicator, Reverse/Fog If Applicable) Before Reinstalling Interior Trim.

Installation Recommendations

• Use Appropriate Hand Tools And A Trim Tool To Avoid Damaging Interior Panels.
• Replace Any Damaged Seals Or Gaskets To Prevent Water Ingress; Ensure Mounting Surface Is Clean.
• Apply Dielectric Grease To Electrical Connectors To Reduce Corrosion And Improve Contact.
• Fit Bulb Holders And Bulbs Specified By Peugeot; Verify Bulb Types For Your Vehicle Variant.
• Check Alignment And Secure Fasteners To Manufacturer’s Tightening Practice To Prevent Vibration Loosening.

Why This Part Most Commonly Fails

Rear Lamps Typically Fail Due To Impact Damage In Minor Collisions, Cracked Or Faded Lenses From UV Exposure, Water Ingress Leading To Corrosion Of Sockets And Connectors, Or Internal Condensation Causing Electrical Faults. Incorrect Bulb Wattage Or Damaged Seals Can Also Accelerate Wear.

This replacement lamp Offers A Cost-Effective Way To Restore Safety And Legal Rear Lighting Performance While Maintaining The Original Look Of The Peugeot 307 SW.

Product Overview

Durable left rear lamp designed for Peugeot 307 SW models (driver’s side). This genuine-style replacement fits vehicles from 2005 and carries common manufacturer references 9655768680, 6350X2 and 6350X3. The unit is supplied without bulb sockets, so holders or bulbs must be purchased separately if required. Ideal for professional workshops and experienced DIY mechanics looking for a direct-fit tail light to restore rear lighting function and exterior appearance.

Key Benefits

• Direct-fit replacement optimised for Peugeot 307 SW (from 2005).
• OEM-referenced numbers included to simplify search and ordering (9655768680, 6350X2, 6350X3).
• Restores Rear Signal, Brake And Tail Light Functions With Correct Installation.
• High-visibility lens design for reliable light output and road safety.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307 SW (From 2005)
• Product Codes: 9655768680, 6350X2, 6350X3
• Other Numbers: 6350.X2, 6350.X3, 6350X2, 6350X3
• Side: Left (Driver’s Side)
• Bulb Sockets: Not Included

Replacement And Installation Guide

Replacement is straightforward for a trained mechanic or competent DIYer with basic tools. Typical steps:

• Open the tailgate and remove any interior trim panels covering the lamp retaining screws.
• Unscrew the lamp securing bolts and carefully unclip the unit from its mounting points to avoid breaking plastic tabs.
• Disconnect the electrical connector and remove the old lamp. If bulb holders are fitted separately, transfer or replace them as needed.
• Position the new lamp, reconnect the wiring and secure the unit with the original fasteners. Refit interior trim panels.
• Test all functions (tail, brake, indicator, reverse if applicable) before finishing the job.

Use correct replacement bulb holders and bulbs rated for vehicle specifications. Ensure sealing surfaces are clean to prevent water ingress. If available, tighten fasteners to manufacturer torque values.

Why This Part Fails Most Often

Rear lamps typically fail or require replacement due to impact damage (minor collisions or parking knocks), cracked lenses, degraded seals leading to condensation and water ingress, broken mounting tabs from stress or aging, and corroded electrical connectors or bulb sockets. UV exposure over years can also cause plastic discoloration and embrittlement, increasing the risk of cracks.

Installation Recommendations

• Handle The Lamp Carefully To Avoid Damaging Mounting Tabs And Sealing Surfaces.
• Replace Any Worn Or Corroded Bulb Holders/Connectors During Installation To Ensure Reliable Operation.
• Check And Clean The Sealing Area On The Body Before Fitting The New Unit To Prevent Future Water Ingress.
• After Installation, Verify All Light Functions From Outside The Vehicle And With A Helper Operating Brake/Indicator Controls.

Compatibility Notes

Designed For Peugeot 307 SW Models From 2005. Use The Listed Product Codes (9655768680, 6350X2, 6350X3) When Searching Or Ordering To Ensure Correct Fitment.

This original-style right rear lamp is a direct-fit replacement for Peugeot 307 SW estate models and is frequently searched by part numbers. It restores full rear signalling and lighting functionality, improves vehicle appearance after damage, and is suitable for professional workshops and DIY mechanics. The lamp is supplied without bulb sockets, allowing you to reuse original holders or fit new ones to match your preferred bulb types.

Features

• Direct-fit replacement for Passenger Side (Right) of Peugeot 307 SW.
• Includes complete lamp housing and lens; bulb holders not included.
• Exact fit to original mounting points for straightforward installation.
• Compatible with common part number references used in repairs and ordering.
• Restores brake, tail and indicator light functions (depending on vehicle wiring).

Technical Information

• Manufacturer: Stellantis (Peugeot)
• Model: Peugeot 307 SW (Estate) — Passenger Side (Right) — From 2005
• Product Codes: 9655768480, 9655768580, 6351X2, 6351X3
• Additional Numbers: 6351.X2, 6351.X3

Installation Recommendations

• Park vehicle on a level surface and switch off ignition. If preferred, disconnect the negative battery terminal to avoid short circuits while working on electrical connectors.
• Open the tailgate and remove the interior trim panel to access the rear lamp mounting nuts or bolts.
• Unscrew the fasteners and carefully pull the lamp assembly outwards to expose the wiring connector.
• Disconnect the wiring harness by releasing the connector clip, then remove the lamp from the vehicle.
• If reusing bulb holders, transfer them from the old lamp to the new unit. Fit new holders if required (holders are not supplied).
• Reconnect the wiring, test all light functions (tail, brake, indicator, reversing if applicable) before refitting trim, then tighten fasteners to the manufacturer’s torque recommendations.
• Avoid overtightening to prevent cracking the lens or deforming mounting tabs.

Most Common Failure Causes

• Water Ingress: Damaged seals or cracked lens can allow moisture into the housing, causing corrosion and electrical faults.
• Impact Damage: Rear collisions or minor bumps commonly crack the lens or break mounting tabs.
• Connector Corrosion: Oxidation of electrical contacts leads to intermittent lighting or failure.
• UV Degradation: Long-term sun exposure can fade or weaken the lens material.
• Bulb Or Holder Failure: Bulbs and holders wear out over time; note that bulb holders are not included with this lamp.

Notes

• Bulb Holders Not Included: This lamp is supplied without bulb sockets. You can reuse the original holders or purchase replacements separately.
• Frequently Searched By Part Numbers: Use the listed product codes when ordering to ensure quick matching.

This used right-hand rear tail lamp is a direct-fit replacement for Peugeot 307 SW models and is commonly sought by mechanics and DIY enthusiasts by its OEM references. The unit houses the rear position (tail), brake and indicator light circuits; bulbs and bulb holders are not included. Supplied as a complete lamp assembly with the original connector and mounting points, it is ideal for repairing damaged rear lighting after minor collisions, cracked lenses or electrical faults.

Compatibility And Application

Fits Peugeot 307 SW (estate) applications. Frequently referenced by part numbers listed below — buyers often search by these codes to confirm fitment. Suitable for models in the 307 I and II range where the same rear lamp assembly is used.

How To Replace

• Open the tailgate and remove the inner trim panel to access the lamp fasteners.
• Unscrew the mounting bolts (usually 2–3) and carefully pull the lamp body outward.
• Disconnect the wiring connector by pressing the locking tab and sliding the plug free.
• Remove the old lamp, fit the replacement assembly, reconnect the wiring and test all functions before closing the trim.
• Refit the trim and tighten fasteners to the manufacturer’s recommendations.

Installation Recommendations

• Work on a cool, dry car and avoid forcing plastic tabs — breakage of clips is the most common cause of poor reassembly.
• Check and, if necessary, replace the rubber gasket or seal around the lamp to prevent water ingress.
• Use dielectric grease on electrical contacts to reduce corrosion and improve long-term reliability.
• Replace bulbs and bulb holders if they show signs of wear, corrosion or melting — this lamp is supplied without sockets/bulbs.
• After installation, verify all light functions (tail/stop/indicator) and ensure lens alignment for correct visibility.

Why This Part Fails Most Often

Rear lamp assemblies commonly fail due to water ingress through deteriorated seals or cracked lenses, leading to corrosion of bulb contacts or short circuits. Impact damage from minor collisions frequently breaks mounting tabs or the outer lens. Heat stress from worn or incorrect bulbs can deform sockets. Corroded wiring connectors from moisture exposure also cause intermittent or complete failure.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 307 SW
• Product Codes: 9655768580, 9655768480
• Other Numbers: 6351X3, 6351X2, 6351.X3, 6351.X2

Keywords to help find this part: Peugeot 307 SW right rear light, tail lamp 9655768580, 6351X3, rear lamp passenger side, used Peugeot tail light.