This door limiter and hinge assembly is an original-fit component for the right front (passenger) door of the Peugeot 207. It secures the door in set open positions, prevents over-travel and reduces stress on the door hinges and body pillar. Ideally suited for professional workshops and competent DIYers who search by part number (9035T4) to ensure correct replacement. Constructed to match the factory mounting points and paint finish (EXL – Obsidian Black) for a precise visual and functional fit.

Features & Benefits

Provides reliable door stopping and controlled opening action to avoid damage to paintwork and bodywork. Direct-fit design simplifies replacement and restores OEM behavior. Compatible finish reduces the need for additional painting when replacing the visible hinge limiter on vehicles finished in Obsidian Black (EXL).

When To Replace

Replace the door limiter if you notice loose or sloppy door movement, the door does not hold in open positions, abnormal noises (clunking or grinding) when opening/closing, visible wear or deformation of the limiter arm, or corrosion that compromises structural integrity. Replacement is recommended after accident damage to the door or A-pillar area, or when wear starts to affect safe door operation.

Replacement Procedure (Overview)

• Prepare: Park on level ground, secure the vehicle, and have appropriate tools ready (torx/sockets, trim tools, torque wrench).
• Support Door: Open the door and support it to prevent sagging—use a padded prop or a second person if necessary.
• Remove Fasteners: Unscrew the mounting bolts that attach the limiter to the body and the inner door. Typical assemblies use two or three bolts on each side.
• Replace Assembly: Install the new limiter in the same orientation, hand-start bolts, then tighten to the manufacturer’s torque specification where available. Check alignment so the door closes and latches correctly.
• Test Operation: Operate the door through its full range, verify the limiter holds in detented positions and there is no binding. Re-check fasteners after a short test drive.

Technical Information

• Manufacturer: Stellantis (Peugeot/Citroën)
• Model: Peugeot 207
• Product Codes: 9035T4
• Additional Numbers: EXL (Obsidian Black Paint)

Recommendation For Installation

Perform installation in a clean, well-lit workspace. Support the door to avoid strain on hinges and latch mechanisms during replacement. Use appropriate torque values for fasteners where available and ensure bolts are tightened evenly. Lubricate pivot points with a suitable grease after installation to prolong service life. If the door alignment changed after replacement, check hinge bolts and striker position and adjust as needed.

Why This Part Fails Most Often

Common causes of failure include metal fatigue from repeated opening/closing cycles, corrosion from road salt and moisture that weakens the housing or bolts, impact damage from accidents or door strikes, and wear of internal detent mechanisms. Lack of lubrication and heavy loads (holding the door open against strong wind) accelerate wear.

Particularly useful for mechanics and experienced DIYers searching by part number 9035T4; ensures fast identification and correct fit for Peugeot 207 right front passenger doors.

This replacement door limiter/hinge is designed for professional workshops and experienced DIY mechanics who need a reliable, direct-fit part for the Peugeot 207. Supplied with the manufacturer code 9037C1 and color designation EXL (Obsidian Black), this component restores correct door stopping, controlled opening angles and smooth closing action. Ideal when the original limiter shows play, binding or causes the door to swing too far or not hold in intermediate positions.

Function And Benefits

The door limiter (door check/strap) together with the hinge secures the left rear door in defined open positions, prevents overextension and reduces stress on the door hinges and body mounts. Replacing a worn or damaged limiter returns correct door positioning, removes rattles and improves user safety when entering or exiting the vehicle. Key benefits include:

• Direct fit to Peugeot 207 left rear door (driver side rear).
• Restores stable door stop positions and prevents uncontrolled opening.
• Painted EXL Obsidian Black to match factory finish for visible areas.
• Useful spare for bodyshops and maintenance garages handling door repairs or accident repairs.

Technical Information

• Manufacturer: Stellantis / Peugeot
• Model: Peugeot 207
• Product Codes: 9037C1
• Additional Numbers: EXL, EXLD (color/variant designation – Obsidian Black)

Compatibility

Fits left rear door of Peugeot 207 models where original part is specified by code 9037C1 or matching EXL paint variant. Suitable for replacement on vehicles with the same mounting geometry and door design. Always verify part code before installation if available on the original part.

Replacement Procedure (Summary)

Recommended for trained mechanics or competent DIYers with proper tools. General replacement steps:

• Open the left rear door and support it to prevent accidental movement.
• Remove interior door trim in the area of the limiter to access mounting fasteners and any electrical connectors (speakers, courtesy lights) if present.
• Unscrew the limiter mounting bolts on the door and body pillar. Retain original fasteners if reusing.
• Fit the new limiter in the correct orientation and tighten fasteners to the vehicle manufacturer’s recommended torque settings.
• Reinstall door trim, test door opening/closing and check stop positions across full range of motion. Confirm absence of noise and proper engagement in each detent.

Recommended Installation

Perform installation on a level surface with the appropriate hand tools and torque wrench. If the door contains airbags, speakers or electrical connectors, isolate the battery before starting work and follow manufacturer safety procedures. After fitting, verify door alignment and function; if door sag or hinge wear is present, address hinge mounting points as well.

Why This Part Fails Most Often

• Wear From Repeated Use: Mechanical detents and moving surfaces wear over time causing play or loss of holding force.
• Corrosion: Water ingress and rust can seize the mechanism or degrade the metal, especially in older vehicles or in regions with road salt.
• Impact Damage: Side impacts or slamming can bend or break the limiter or its mounting points.
• Paint/Coating Damage: Loss of protective paint (including visible EXL finish) accelerates corrosion of the exposed parts.

Part number and color code (9037C1, EXL) are commonly used when searching for replacements—include these codes in your search to find matching units quickly.

Product Overview

This Left Front Door Check/Stop Hinge (Driver’s Door) is an original-design replacement for Peugeot 207 models. It controls door travel, holds the door in set open positions and prevents over-rotation that can damage the door shell or adjacent bodywork. The EXL finish in Obsidian Black ensures a factory-matching appearance where the part is visible.

Why Choose This Part

• Direct Fit For Peugeot 207 — Designed To Match OE Mounting Points For Fast, Accurate Installation.
• Restores Proper Door Operation — Eliminates Excess Play, Slamming And Unreliable Door Retention.
• Durable Finish — Painted In Obsidian Black (EXL) To Match Factory Trim And Resist Corrosion.
• Suitable For Professional Garages And Self-Repair Enthusiasts — Commonly Searched By Part Number 9035T5.

Symptoms Indicating Replacement

Replace The Door Check/Stop If You Notice:

• Door Does Not Hold In Open Positions Or Falls Shut.
• Excessive Lateral Play Or Loose Feeling When Opening/Closing.
• Grinding, Clicking Or Unusual Noises From The Hinge Area.
• Visible Corrosion, Deformation Or Damage To The Check Strap/Bracket.

How The Part Fails And Typical Causes

The Most Common Reasons For Failure Are Wear Of The Pivot Or Check Mechanism, Corrosion From Moisture And Road Salt, Mechanical Damage From Impacts Or Repeated Slamming, And Fatigue Of Internal Components. Failure Leads To Poor Door Retention, Misalignment And Noise.

Replacement Guide

The following gives an overview of the replacement procedure for an experienced mechanic or a competent DIYer. Always Follow The Vehicle Manufacturer’s Service Manual For Exact Procedures And Torque Values.

• Support The Door Securely Before Starting To Prevent Dropping Or Misalignment (Use A Jack With Soft Support Or Assistant To Hold The Door).
• Open The Door To Access The Check/Stop Area And Remove Any Trim Or Protective Covers As Required.
• Unscrew The Fasteners That Secure The Door Check To The Body And Door (Keep Track Of Fastener Type And Position).
• Remove The Old Check Carefully, Inspect Mounting Holes And Surrounding Paint For Damage Or Corrosion.
• Install The New Unit In Reverse Order, Ensuring Correct Alignment. Tighten Fasteners To Manufacturer’s Specification.
• Check Door Operation Through Full Travel, Confirm That The Door Holds In Positions And That There Is No Unwanted Play Or Noise.

Installation Recommendations

• Always Support The Door To Avoid Stressing Hinges Or Wiring.
• Replace Fasteners If They Are Stretched, Corroded Or Damaged.
• Clean And Treat Mounting Surfaces To Prevent Future Corrosion.
• Adjust Door Alignment If Necessary After Installation To Ensure Even Gaps And Proper Latch Engagement.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Peugeot 207
• Product Codes: 9035T5
• Additional Numbers: EXLD; Color: EXL – Obsidian Black Paint; Position: Left Front (Driver’s Door)

Most Common Reason For Part Failure

The Part Typically Fails Due To Progressive Wear And Corrosion, Often Accelerated By Environmental Factors (Moisture, Road Salt) Or Mechanical Shock From Impacts And Repeated Door Slamming. Preventive Maintenance Includes Regular Inspection, Cleaning Of Mounting Areas And Prompt Repair After Any Door Impact.

Compatibility And Notes

This Item Is Intended For Use On The Left Front (Driver’s) Door Of Peugeot 207 Vehicles. Customers Frequently Search Using The Part Number 9035T5, So Confirm Fitment Against Vehicle Model And Year When Selecting Parts.

Durable replacement door stop and hinge assembly designed for the right rear door of the Peugeot 207. This unit (OEM Code 9037C0 / EXLD) restores correct door opening control, holding positions and preventing overextension. Manufactured to match the original fitment, it is ideal for professional garages and experienced DIY mechanics who need a direct-fit part to maintain safe and smooth door operation.

Key Functions

– Controls Door Opening Angle And Holds Door In Detented Positions
– Prevents Door Overextension And Reduces Stress On Hinges And Body Mounts
– Ensures Smooth, Predictable Door Movement When Entering Or Loading The Vehicle

Technical Information

Manufacturer: Peugeot (Stellantis)

Model: Peugeot 207

Product Codes: 9037C0, EXLD

Other Numbers: Not Specified

Installation Recommendation

Installation should be performed with the door properly supported to avoid misalignment or damage. Typical replacement steps:

1. Remove Inner Door Trim And Any Obstructing Panels To Access Hinge/Stop Fasteners.
2. Support The Door Securely (Use A Jack Or Assistant) To Prevent Sagging When Fasteners Are Removed.
3. Remove Fasteners Holding The Old Door Stop/Hinge And Compare New Unit For Correct Orientation.
4. Fit The New Unit, Tighten Fasteners To Manufacturer’s Specification, And Check Door Alignment And Closing Action.
5. Lubricate Pivot Points Lightly After Installation And Refit Interior Trim.

For best results, Verify Door Alignment And Seal Compression After Install. Replace Any Damaged Fasteners Or Clips. If You Are Unsure About Alignment Or Adjustment, Have The Work Performed By A Professional With The Proper Tools.

Why This Part Fails Most Often

Common causes of failure include corrosion (especially in regions with road salt), Accumulated Dirt And Debris Causing Wear, Repeated Heavy Use And Slamming, Or Mechanical Damage From Impacts/Accidents. Wear Leads To Loose Detents Or Stiff Movement, Which Makes The Door Hard To Control And Can Cause Additional Stress On Door Hinges And Striker Points.

Fitment And Notes

Designed For Use On Right Rear Door (Passenger Side Rear) Of Peugeot 207. Often Searched By Part Number 9037C0. Color Code EXL Corresponds To Black Obsidian Paint Finish Where Applicable.

Choose This Direct-Fit Replacement If You Need Reliable Door Control And OEM-Compatible Mounting For Peugeot 207. Order Now To Restore Safe And Smooth Operation Of The Right Rear Door.

Part description

This left front door stop for Peugeot 207 serves to continuously limit the opening of the doors and to hold them in typical positions. It helps protect the hinges and the door itself from excessive stress (e.g. during sudden opening or a gust of wind) and contributes to the safe operation of the door without unwanted noises and “skipping”.

The part is from a low mileage car and is listed as solid and tested. For used stops, it is essential that they have the right stiffness and are not squeezed in the joints – these are exactly the properties that you will feel the most in practice during replacement.

Technical information

• Manufacturer: Stellantis Citroën Peugeot
• Model: Peugeot 207
• Other numbers: ETSC, 15589080

• Type of part: stop / door limiter
• Side: left front door
• Color: ETS – Cendre gray lacquer

Product codes

• Product codes: 23709080, 9035T5

Installation recommendations

Generally/typically replacing a door stop is mechanical work in the door and A-pillar area. The exact design may vary depending on the specific design of the car.

1) Before assembly (checks of used part)

• Compare the new stop with the old piece: shape, length, fit, orientation and markings/codes (if visible).
• Check that the stop is firm, without excessive play in the joints and without cracks or deformations.
• Check the condition of the mounting holes/pins – they must not be squeezed out.

2) Necessary tools and materials (in general)

• Normal set of gola/ratchet and attachments, or bits depending on the used connecting material
• Pry bar/plastic pry bar for removing covers or upholstery (if access is obstructed)
• Door support or helper to secure the door in the open position
• Work gloves, possibly cleaning agent for degreasing

3) Step-by-step assembly procedure

1. Secure the vehicle against movement and open the door to a stable position.
2. Support the door or get a helper – manipulating the stop can change the stability of the open door.
3. If it obstructs access, remove the relevant covers/section of upholstery in the area where the stop is attached (careful not to damage the clips).
4. Release the fasteners of the stop on the side of the door.
5. Release the stop fasteners on the body side.
6. Remove the old stop and check the contact surfaces (corrosion, dirt, bruises).
7. Clean the mating surfaces and threads (if dirty) so that the stop fits without tension.
8. Insert the stop in the correct position and first lightly clamp it on one side (without final tightening).
9. Attach the other side of the stop and check that the stop does not conflict with the position of the door and nothing twists.
10. Tighten the fasteners gradually and evenly.
11. Perform the opening/closing of the door several times and observe the fluidity of the operation and holding in the positions.
12. Reinstall the removed covers/upholstery and double check that nothing rubs anywhere.
• 4) Post-assembly checks and functional test verification
  • Check that the door opens smoothly, without metallic sounds and without “skipping”.
  • Verify that the stop actually restricts opening and the door holds in typical positions.
  • Inspect the fasteners for loosening and the stop for play.

  5) The most common assembly mistakes + how to avoid them

  • Unsecured door: there is a risk of switching the stop or damaging the hinge – always support the door.
  • Ignoring play: if there is play in the mounting, the door will click – check the stop and the mounting before assembly.
  • Assembly “by force”: the stop must sit without tension; check the orientation and contact surfaces for resistance.

  Reasons why the part is damaged

  • Frequent sudden opening of the door and reaching the stop (mechanical overload).
  • Gusts of wind, when the door is “torn” to the extreme position.
  • Wearing of joints and friction parts – formation of backlash, clicking and irregular operation.
  • Corrosion and dirt in the mechanism (mainly for cars operated in demanding conditions).
  • Damage after an accident or after hitting the door/hinge, when misalignment occurs and the stop is stressed off-axis.
  ]]> https://www.usedpartsvendor.com/body/door-stops/207-door-stops/left-rear-door-hinge-stop-etsc-peugeot-207-15189580-9037c1/ Sun, 25 Jan 2026 03:01:42 +0000 https://www.usedpartsvendor.com/uncategorized/left-rear-door-hinge-stop-etsc-peugeot-207-15189580-9037c1/ Door Stop – Left Rear Door Limiter For Peugeot 207. Removed From A Vehicle With 46,000 km. Color ETS – Paint Grey Cendré. Solid – Tested.

  This left rear door limiter (door stop / door check strap) is a direct-fit replacement for Peugeot 207 vehicles and is frequently sought under the product numbers 15189580 and 9037C1. Constructed to withstand repeated opening and closing, it preserves door travel and prevents over-extension. Ideal for professional mechanics and DIY enthusiasts who need an OEM-style part to restore correct door behaviour after wear, minor impact or corrosion.

  Technical Information

  • Manufacturer: Peugeot (Stellantis)
  • Model: Peugeot 207
  • Product Codes: 15189580, 9037C1
  • Additional Numbers: ETSC, Paint Grey Cendré

  Installation Recommendations

  • Prepare Tools: Basic hand tools (Torx/sockets), trim removal tools and a torque wrench.
  • Access: Open the rear left door fully and, if needed, remove the inner door trim to access the limiter mounting bolts and any retaining clips.
  • Support: Support the door to avoid unwanted movement while removing the fasteners.
  • Removal: Unscrew the limiter fasteners (retain bolts for reuse if undamaged) and gently pull the limiter free from its mounts. Note mounting orientation to install the new unit correctly.
  • Installation: Fit the replacement limiter in the same position, align mounting holes and tighten fasteners to the manufacturer’s recommended torque values where available. Check free movement and door catch points before reassembling trim.
  • Final Checks: Open and close the door several times to confirm smooth operation, correct stopping points and absence of binding. Lubricate pivot points with appropriate grease if necessary.

  Why This Part Fails Most Often

  • Wear And Fatigue: Repeated cycles of opening and closing cause mechanical wear of the pivot and detent surfaces.
  • Corrosion: Exposure to moisture and road salt can corrode metal components or fasteners, leading to stiffness or failure.
  • Impact Damage: Door impacts or heavy slamming can bend or break the limiter or its mounting points.
  • Fastener Failure: Stripped or seized bolts and damaged threads prevent correct mounting and can lead to premature failure.

  Particularly useful when customers search by OE numbers 15189580 or 9037C1. The unit supplied matches the colour designation ETS – Grey Cendré and was removed from a Peugeot 207 with 46,000 km on the clock.

  ]]> https://www.usedpartsvendor.com/body/door-stops/308-t9-door-stops/peugeot-308-t9-front-door-stop-9677466980/ Fri, 09 Jan 2026 03:01:00 +0000 https://www.usedpartsvendor.com/uncategorized/peugeot-308-t9-front-door-stop-9677466980/ Stop – limiter of the front left and right doors for the PEUGEOT 308 T9 car

  Part description

  The limiter (stop) of the front door for the Peugeot 308 T9 is used to smoothly limit the opening of the door and to stabilize it in individual positions. It helps protect the hinges and the door itself from overloading when opening and increases comfort when getting in.

  This part is intended for front left and front right doors (depending on the version on the car). When replacing, the situation is typically solved when the door does not hold in an intermediate position, “jumps” when moving, or there is a clicking/creaking sound.

  Technical information

  • Manufacturer: PSA Citroën Peugeot
  • Model: Peugeot 308 T9
  • Other numbers: not specified

  Product codes

  • Product codes: 9677466980

  Installation recommendations

  • Before assembly, check for mechanical damage to the limiters and the condition of the fixings in the doors and in the body pillar.
  • It is recommended to also check the condition of the hinges and any clearance in the door – excessive clearance can shorten the life of the limiter.
  • After assembly, test the function in all opening positions: the door should move smoothly and without skipping.

  Reasons why the part is damaged

  • Frequent sudden opening of the door all the way (e.g. in the wind).
  • A strong gust of wind into an open door, which overloads the mechanism.
  • Wear of the limiter mechanism (clicking, skipping, not holding positions).
  • Hinge play or poor door alignment that increases the stress on the stop.
  • Corrosion and dirt in the area of attachment and moving parts.
  ]]> https://www.usedpartsvendor.com/body/door-stops/c3-picasso-door-stops/stopping-the-right-front-door-ewpb-citroen-c3-picasso-9035en/ Fri, 01 Aug 2025 02:08:16 +0000 https://www.usedpartsvendor.com/uncategorized/stopping-the-right-front-door-ewpb-citroen-c3-picasso-9035en/ Product Overview

  This right front door stopper (door limiter) is specifically designed for the Citroën C3 Picasso, ensuring that the vehicle’s front right door opens and closes correctly and safely. Coated in EWP color finish, a distinctive white Banquise lacquer, this stopper offers a solid and reliable solution for door movement control.

  Ideal for mechanics and car enthusiasts performing their own repairs, this part not only restores the door’s proper function but can also extend the longevity of the door components by preventing excessive movement and wear. The part meets stringent quality standards, guaranteeing durability and dependable performance on your Citroën C3 Picasso.

  Technical Information

  • Manufacturer: Citroën
  • Model: Citroën C3 Picasso
  • Product Codes: 9035EN, 9035FQ
  • Additional Numbers: EWPB

  The door stopper plays a critical role in limiting door travel, preventing door damage and ensuring user safety. Regular checks or replacement may be necessary as wear can cause the stopper to lose effectiveness, leading to door misalignment or rattling. Installation is straightforward and requires no special modifications, making it suitable for both professional workshops and skilled DIY mechanics.

  If you have any questions about this part or installation guidelines, please do not hesitate to contact our customer support team. We are committed to providing expert advice and helping you maintain your vehicle with confidence.

  Choosing reliable parts sourced from trusted providers will help maintain your Citroën C3 Picasso’s performance and reliability. Invest in quality components like this door stopper to ensure your vehicle stays safe and functional for years to come.

  ]]> https://www.usedpartsvendor.com/body/door-stops/c3-picasso-door-stops/stop-left-front-door-ewpb-citroen-c3-picasso-9035el/ Fri, 01 Aug 2025 02:08:16 +0000 https://www.usedpartsvendor.com/uncategorized/stop-left-front-door-ewpb-citroen-c3-picasso-9035el/ The Left Front Door Hinge Stop for Citroën C3 Picasso is designed to limit the door’s movement, preventing damage to both the door and the vehicle’s bodywork. This crucial component (product code 9035EL) features a robust construction finished in EWP White Banquise paint, matching the original vehicle aesthetics while providing long-lasting durability.

  This hinge stop plays an essential role in protecting the door from excessive opening, which is especially important in tight urban environments and parking spaces. Its firm and tested structure helps reduce impact stress on the door and surrounding panels, maintaining proper door alignment and smooth operation over time.

  Technical Information:
  Manufacturer: Citroën
  Model: C3 Picasso
  Product Codes: 9035EL, 9035FR, EWPB
  Additional Numbers: Not Available

  Installation should ideally be performed by a qualified technician to ensure correct mounting and optimal door functionality. This part is perfect for professional mechanics and car owners who want a reliable and durable replacement part to maintain safety and performance of their Citroën or Peugeot vehicle.

  ]]> https://www.usedpartsvendor.com/body/door-stops/c3-picasso-door-stops/stopping-left-rear-door-ewpb-citroen-c3-picasso-9035cl/ Fri, 01 Aug 2025 02:08:16 +0000 https://www.usedpartsvendor.com/uncategorized/stopping-left-rear-door-ewpb-citroen-c3-picasso-9035cl/ Description

  This left rear door hinge stop is designed specifically for the Citroen C3 Picasso, providing a dependable solution for replacing worn or damaged parts. Coated in EWP – White Banquise paint finish, it ensures a perfect color match with your vehicle, maintaining both functionality and aesthetics.

  The main function of this hinge stop is to limit the opening angle of the rear left door, protecting both the door and bodywork from damage. This is particularly important in tight spaces or when the rear doors are frequently used, preventing costly repairs to the door edges or hinges.

  Installation is straightforward and does not require specialized tools, allowing both professional mechanics and DIY enthusiasts to quickly restore the door’s proper function and safety. Over time, this part may wear out due to regular use, so timely replacement helps maintain the vehicle’s optimal condition.

  Technical Information

  • Manufacturer: Citroen
  • Model: Citroen C3 Picasso
  • Product Codes: 9035CL, 9035FP, EWPB
  • Additional Numbers: N/A

  Compatible exclusively with the Citroen C3 Picasso, this part guarantees a precise fit and reliable performance. Choosing this genuine-quality hinge stop helps keep your vehicle in excellent shape and prevents door-related issues caused by worn components.

  Trust in a quality solution that combines durability with perfect color matching and simple installation. Order now to ensure your Citroen C3 Picasso remains fully functional and protected against everyday wear on the rear left door hinge.

  ]]>