This used front door stop (door limiter) is a direct-fit replacement commonly used on the five‑door Citroën C1 and Peugeot 107. Designed to limit the door opening angle and hold the door in intermediate positions, this part helps prevent damage to the door, hinges and nearby bodywork while allowing smooth, controlled opening. The unit is frequently searched by part numbers, so you can find the correct spare quickly using codes such as 9181T8 or 760080.

Technical Information

Manufacturer: Stellantis

Model: Citroën C1 / Peugeot 107 (Five‑door)

Product Codes: 9181T8

Additional Numbers: B0 00760080, 760080

Fitment

• Citroën C1 – 5‑door versions
• Peugeot 107 – 5‑door versions

Function

The door stop (door limiter) controls the maximum opening angle of the front door and provides intermediate catch positions so the door remains partially open without swinging freely. It consists of a mechanical arm/strap and a housing mounted between the door and the body, absorbing forces during normal use and minor impacts.

Common Failure Reasons

• Wear And Fatigue: Repeated use causes internal components (plastic guides or metal strap) to wear, leading to loose or inconsistent catches.
• Corrosion: Moisture and road salt can corrode metal parts and fasteners, especially in older cars or those used in harsh climates.
• Impact Damage: Minor collisions or slamming doors can bend or break the mechanism.
• Contamination: Dirt and grime ingress can increase friction and accelerate wear.

Replacement / Installation

Typical replacement is straightforward for an experienced mechanic or competent DIYer. General procedure:

• Open the door to access the limiter area (inner edge where door meets body).
• Support the door to prevent it from sagging when the limiter is removed (use a jack or assistant if necessary).
• Remove any trim or rubber covers concealing the limiter mounting bolts.
• Unfasten the mounting bolts on the body and on the door side, then withdraw the old limiter.
• Fit the replacement part, align it in the same position and tighten fasteners securely. Check door operation and adjust if required.

Installation Recommendations

• Inspect hinge bolts and surrounding mounting points for wear or corrosion; replace corroded fasteners.
• Clean mating surfaces and apply suitable anti‑seize or light grease to moving points if recommended by workshop practice (avoid contaminating door seals or painted surfaces).
• Always support the door during removal/installation to avoid straining hinges or wiring harnesses inside the door.
• After installation, verify free movement and that the door remains secure in catch positions; adjust alignment if the door does not close or latch correctly.
• Because this part is often sold under its product number, check the code stamped on the old limiter and compare with the supplied reference (e.g. 9181T8) before fitting.

Why Replace?

Drivers usually replace the door stop when the door no longer stays in intermediate positions, opens or closes roughly, or if the limiter is visibly damaged or corroded. Replacing a worn or broken limiter restores safe, predictable door movement and prevents further stress to hinges and body panels.

This door stop serves as a front door limiter specifically designed for the Citroën C1 and Peugeot 107 three-door models. It plays a vital role in controlling the door opening angle, preventing excessive swinging that can damage door hinges or nearby bodywork. Ideal for professional auto mechanics as well as DIY enthusiasts, this component is often searched for by its product numbers 9181J7 and B000760180.

The door stop is usually mounted inside the door frame and works by providing a fixed mechanical stop, ensuring the door opens to a safe and ergonomic angle. Over time, frequent use, exposure to weather conditions, or physical impacts can cause the original door stop to wear out or break, leading to improper door function or even damage to the door’s structure.

Replacement Guidance

Replacing the door stop is a relatively simple process suitable for experienced DIY car owners and automechanics alike. The process typically requires removing the interior door panel to access the mounting area. Once the old stop is removed, the new one is installed using standard tools and secured firmly in place. Proper alignment is crucial to ensure the door opens smoothly and stops at the correct position.

Technical Information

• Manufacturer: PSA Group (Citroën Peugeot)
• Model Compatibility: Citroën C1 (three-door), Peugeot 107 (three-door)
• Product Codes: 9181J7, B000760180
• Additional Numbers: —

Using the correct door stop helps maintain the structural integrity of your vehicle’s doors, reduces noise caused by loose components, and improves overall driving safety. It is recommended to inspect door stops during regular vehicle maintenance and replace them at the first signs of wear.

High-quality door check designed for the rear doors of five-door first-series CITROËN C1 and PEUGEOT 107. This replacement door stopper (door limiter/door check) ensures controlled door opening and secures the door in defined positions to prevent over-travel and damage to hinges or bodywork. Ideal for professional mechanics and experienced DIYers who look for a direct-fit component often searched by OEM codes 9181J6 and B000760280.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C1 (First Series), Peugeot 107 (First Series) — Five-Door
• Product Codes: 9181J6, B000760280
• Other Numbers: 9181J6 | B000760280

Function And Benefits

The door stop limits the swing of the rear doors, holding them in predefined positions to make entry and exit easier and to protect the door hinges and surrounding bodywork. It Provides Smooth Detents, Reduces Noise From Slamming, And Minimizes Stress On The Hinge Pins.

Typical Failure Modes

This part most commonly fails due to mechanical wear of internal components or plastic bushings, corrosion from road salt and moisture, impact damage (doors slammed hard or struck), and gradual fatigue from frequent use. When the limiter is worn, symptoms include excessive play, failure to hold the door in detent positions, clicking or grinding noises, and visible damage or deformation of the stopper.

Installation Recommendations

• Support The Door: Use a suitable support or helper to hold the door in position and avoid damaging hinges or wiring during removal.
• Access The Mounting Points: Remove inner trim if necessary to reach the fixing bolts between the door and body.
• Remove The Old Unit: Unscrew the fasteners securing the door check to the door shell and to the body. Keep fasteners if they are reusable and in good condition.
• Fit The New Unit: Position the new limiter, secure fasteners and tighten to the manufacturer’s torque specifications (refer to the vehicle repair manual).
• Lubrication And Check: Lightly lubricate pivot points with a suitable grease, operate the door through its full travel and verify correct engagement in detent positions.
• Final Inspection: Check Door Alignment And Closing Function After Installation; Ensure No Binding Or Excessive Play.

Replacement Interval And When To Replace

There Is No Fixed Service Interval. Replace The Door Stop When You Observe Excessive Play, Failure To Hold Door Positions, Unusual Noises, Visible Wear Or After Impact Damage. Regular Visual Inspection During Routine Service Will Help Identify Wear Early.

Frequently searched by OEM codes 9181J6 and B000760280, this direct-fit door limiter is a practical and cost-effective repair to restore safe and reliable door operation on five-door first-series Citroën C1 and Peugeot 107 models. Suitable For Garage Replacement And DIY Projects With Basic Mechanical Tools.