Replacement exterior door handle designed for Citroën and Peugeot models. This painted FXT Cornelie Black handle fits the right front and rear doors and is a direct-fit part for vehicles specified below. Intended For Use By Professional Technicians And Experienced DIY Enthusiasts; Often Searched By Product Codes 9101LY And 96868965XT.

Key Features

• Exterior Door Handle For Right Front And Rear Doors
• Painted Finish: FXT Cornelie Black — color-matched To Exterior
• Direct Fit For Specified Citroën And Peugeot Models
• Durable Construction With Internal Metal Components And Painted Plastic Cover
• Commonly Referenced By OE Codes 9101LY And 96868965XT

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4 II (B7), C‑Elysée, DS4, Peugeot 301
• Product Codes: 9101LY; 96868965XT
• Additional Numbers: 9101LY | 96868965XT

Function And Application

This part is an exterior door handle that operates the mechanical latch and connects to the door lock/linkage. It provides the user interface to open the door from the outside and transmits movement to the latch assembly via rods or cables. Suitable For Right Side Front And Rear Doors On The Listed Models.

How To Replace

1. Prepare Tools: Trim Removal Tool, Philips And Flat Screwdrivers, Socket Set, Torx Bits, Pliers.
2. Remove Interior Door Trim Panel Carefully To Access The Handle Fixings; Start With Trim Clips, Then Remove Screws And Lift Panel Off.
3. Peel Back The Vapor/Water Shield To Reach The Handle Area.
4. Disconnect The Linkage Rods Or Cables From The Handle (Note Their Orientation For Reassembly) And Unclip Any Electrical Connectors For Central Locking If Present.
5. Unscrew The Retaining Bolts Or Nuts Holding The Handle From The Inside Of The Door, Then Remove The Old Handle From The Outside.
6. Install The New Handle: Position From Outside, Tighten Fasteners From Inside, Reconnect Linkages And Electrical Connectors, Ensuring Secure Clips And Correct Alignment.
7. Test Operation Of Mechanical Latch And Central Locking Before Reassembling The Door Trim. Ensure Smooth Movement And No Binding.
8. Reinstall Water Shield And Door Trim, Verify All Clips And Screws Are Secured.

Installation Recommendations

• Check And Replace Any Broken Plastic Clips Or Retaining Fasteners During Installation.
• Apply A Light Lubricant To Moving Metal Parts And Pivot Points To Reduce Wear.
• Align Handle Carefully To Avoid Excessive Stress On Linkage Rods.
• If The Door Has Electric Components (Central Locking, Sensors), Disconnect The Battery Before Working On Electrical Connectors.
• Use Proper Trim Tools To Avoid Damaging Interior Panels And Clips.
• Verify Paint Match Before Final Installation; Minor Touch-Up Can Be Done By A Bodyshop If Needed.

Why The Part Most Often Fails

• Mechanical Wear: Repeated Use Causes Plastic Lugs, Clips Or Internal Mechanisms To Wear Or Break.
• Impact Damage: Door Handle Breakage From Accidents Or Strong Impacts.
• Plastic Brittleness And UV Degradation: Prolonged Sun Exposure Can Make Painted Plastic Brittle, Leading To Cracks.
• Corrosion Of Internal Metal Components Or Fasteners, Especially In Areas With Road Salt.
• Faulty Or Misaligned Linkage Rods And Worn Door Latch Increasing Load On The Handle.

Compatible With Models Listed Above When Fitted According To Manufacturer Guidelines. Use The Product Codes 9101LY Or 96868965XT When Searching For This Exact Replacement Handle.

High-quality replacement exterior door handle designed for the left front (driver) door of several Citroën and Peugeot models. This part is a direct-fit option referenced under codes 9101LX and 96868964XT and is ideal for professional workshops and competent DIY enthusiasts who need a reliable, appearance-matching repair. The handle matches original styling in Cornelie Black (FXT) and restores secure door latching and smooth operation of the exterior opening mechanism.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4 II (B7), C‑Elysée, DS4, Peugeot 301
• Product Codes: 9101LX, 96868964XT
• Additional Numbers: Driver Side, Left Front Door Handle, Color FXT (Cornelie Black)

Compatibility And Application

This handle is intended for the driver side (left front) door on the listed vehicle models. It reinstates the exterior grip and lever that operates the latch mechanism and integrates with the vehicle’s locking and opening linkage. When ordering, searching by product codes 9101LX or 96868964XT typically returns the correct part quickly.

Installation Recommendations

• Recommended For: Qualified Auto Technicians And Skilled DIYers.
• Preparation: Work With The Door Panel Off To Access Mounting Bolts, Linkage Rods, And Retaining Clips.
• Procedure Summary: Remove Interior Door Trim (careful with clips), detach water shield if present, unscrew the handle mounting fasteners, disconnect the mechanical linkage and any electrical connector for central lock if applicable, fit the new handle, reconnect linkage and connectors, test operation before reassembling the door panel.
• Best Practice: Check And Replace Worn Clips Or Fasteners During Installation To Ensure A Secure Fit And Prevent Rattles.
• Safety: Use Proper Trim Tools To Avoid Damaging Interior Panels Or Seal Materials.

Function And Common Failure Modes

The exterior door handle provides the mechanical interface to unlatch the door from outside and often houses the actuator linkage for central locking. Common failure causes include plastic fatigue and cracking from repeated use, broken internal clips or mounting tabs, corrosion or wear of metal pivot components, and damage from impacts or slamming. UV exposure and long-term temperature cycling can accelerate material deterioration, especially on frequently used driver-side handles.

Service Life And Maintenance

Service life varies with use and environment; many handles remain functional for several years, while high-mileage or harsh-climate vehicles may require replacement sooner. Inspect the handle for play, visible cracks, or damaged mounting ears during routine service intervals. Replacing worn fasteners and lubricating pivot points during repair can extend the working life of the mechanism.

Why Choose This Part

Offers a cost-effective, appearance-matching repair for exterior door damage or wear. Clear product references (9101LX, 96868964XT) help locate the correct part quickly in catalogs and online search. Suitable for body shops, mechanical garages, and experienced DIY repairs where a direct, visually consistent replacement is required.

Search Tip

Common Search Keywords: 9101LX, 96868964XT, Left Front Door Handle, Driver Side Door Handle, Citroën C4 II, C‑Elysée, DS4, Peugeot 301.

Original inner right door handle (front and rear) for Citroën and Peugeot cars in HVV – Silver design. This is a used, fully functional OEM part from disassembly. Often searched under 98201552VV and 98000002VV (PSA). Ideal replacement for a damaged or loose handle; dimensions and mounting correspond to the original, assembly is quick and without modifications.

Main advantages
– Genuine PSA/OEM part – precise fit, reliable function
– The right color and HVV finish (Silver) to match the interior
– Suitable for right front and rear doors (LHD – European cars)
– Quick replacement, compatibility verifiable by part number

Technical information
– Name: inner door handle, right (synonyms: handle, handle, door opening lever)
– Location: right side (passenger’s side for cars with left-hand drive); use on front and rear doors depending on equipment
– Color/design: HVV – Silver
– OEM/PSA part numbers: 98201552VV, 98000002VV
– Condition: used part, fully functional; may bear normal cosmetic traces of use
– Assembly: screwed attachment, connection to the lock rod; without the need for modifications
– Packaging/Contents: We deliver what is shown in the product photos

Compatibility (selected models and years/equipment)
– Citroën C4 II
– DS4
– Peugeot 208
– Peugeot 308 T9
– Peugeot 3008 I
– Peugeot 5008 I
– Peugeot 508
Note: Actual compatibility may vary by year of manufacture and equipment. Before ordering, we recommend checking against OEM number 98201552VV / 98000002VV or VIN.

For whom and why
– For car mechanics and DIYers: quick replacement of the original without working with non-original parts
– Solves typical problems: loose handle, cracked lever, non-functioning opening from the interior
– From an economic point of view: a quality used original often lasts longer than a cheap new product

Assembly tips
– Before assembly, compare the shape, fit and end of the tie rod with the old part
– Work with clean plastics, we recommend lightly lubricating the mechanical contact surfaces
– If you are only changing one side, check the HVV – Silver color match with the other side

SEO/numbers for easy tracking
– 98201552VV, 98000002VV, 9820 1552 VV, 9800 0002 VV
– inner handle right Citroën Peugeot, door handle right, door opening handle HVV Silver

Need to check compatibility? Send us the VIN – we will check if the crank 98201552VV / 98000002VV is suitable for your car.

Original inner door handle – left (L) for Citroën/Peugeot cars in the color HVV Silver. This is a used, fully functional part from disassembly, suitable as a direct replacement for the original handle. Often searched under OEM numbers 98201553VV and 98000001VV.

Main advantages
– Genuine PSA part: exact fit, correct color and finish
– Compatibility with the left front and rear doors of selected models
– Quick replacement – it is usually enough to transfer the original screws and the lock rod/cable
– Savings compared to a new part, while full functionality

Technical information
– Location: door interior (inside handle)
– Side: left (driver’s side for cars with a steering wheel on the left)
– Position: front left and rear left door (depending on model equipment)
– Color/surface: HVV – Silver
– OEM/cat. numbers (PSA): 98201553VV, 98000001VV
– Material: high-quality plastic with decorative silver finish
– Condition: used original, fully tested; may bear minor cosmetic traces of normal use

Compatibility according to PSA models
– Citroën: C4 II, DS4
– Peugeot: 3008 I, 5008 I, 308 T9
– Furthermore, in practice it is found in some versions of 208 and 508 (verify by OEM number or VIN)
Note: Compatibility may vary by year of manufacture and specific equipment. The safest bet is to compare the part numbers on your original crank.

How to correctly verify the suitability of a part
– Check OEM number match: 98201553VV, 98000001VV
– Compare the color/finish of the HVV Silver with the original part
– In case of uncertainty, send us the VIN – we will verify compatibility for you

Assembly tip
– When replacing, transfer the original cable/rod and fasteners (if not included). Replacement is usually quick and manageable at home with basic tools.

Keywords for easy search
interior door handle left, Citroën door handle, Peugeot handle, HVV Silver, 98201553VV, 98000001VV, original PSA part, door handle, door opening interior

Looking for a reliable, accurate replacement without tedious customization? This original left inner handle in HVV Silver is an ideal choice for quick repair and professional service.

Product Overview

This OEM-style exterior door handle (product code 9101LW / EZRC) is a direct-fit replacement for several Citroën and Peugeot models. Designed to restore original appearance and function, the part is supplied in Metallic Gray (Grey Aluminium paint code EZRC) and is available in other factory colors upon request. Ideal for professional garages and DIY mechanics who search by part number (9101LW) to ensure fast compatibility checks and quick repairs.

Why Choose This Door Handle

High relevance for garages and independent repairers: the handle is offered with the factory paint finish ready to install, reducing time-consuming painting and adjustment. The direct-fit design minimizes modifications to linkages and mounting points, so replacement is straightforward on supported vehicles. Stock availability in multiple colors helps maintain original vehicle aesthetics after accidental damage or wear.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C4 II (B7), Citroën C-Elysée, DS4, Peugeot 301
• Product Codes: 9101LW, EZRC
• Additional Numbers: Paint Code LAK Grey Aluminium (EZRC)

Function And Common Faults

The exterior door handle operates the mechanical linkage between the exterior release and the door latch. Common failure modes include broken plastic mounting tabs or internal levers, wear or jamming of the release mechanism, paint damage from impacts, and corrosion of metal components that can lead to stiff operation. Handles may also be damaged by forced entry or collisions.

Replacement Guide

Typical replacement requires removing the inner door trim to access the handle mounting bolts and linkages. General steps:

1. Remove door card/panel carefully to avoid breaking clips and to expose inner door components.
2. Disconnect any electrical connectors if the handle has an integrated sensor or lighting.
3. Unbolt or unclip the exterior handle retaining fasteners from the inside of the door.
4. Release the mechanical linkages (rods or cables) from the handle and transfer any retaining clips to the new handle if required.
5. Fit the new handle, secure fasteners, reconnect linkages and electrical connectors, then test door operation before reassembling the door card.

Installation Recommendations

• Use the correct trim tools to avoid damaging panel clips and trim surfaces.
• Inspect and, if necessary, replace small plastic clips and rods—these are common weak points and often fail when the handle itself is damaged.
• Lubricate moving parts of the latch and linkages with suitable grease after installation to ensure smooth operation.
• Perform a full functional check (open/close/lock/unlock) before refitting the door trim.
• For handles with integrated sensors or illumination, verify electrical connections and bulb/LED function prior to final assembly.

Why This Part Fails Most Often

The most frequent causes of failure are mechanical stress (forced opening, slamming), impact damage (parking lot collisions), degradation of plastic mounting tabs due to ageing, and corrosion in regions with aggressive road salt. Wear from high-frequency use can also loosen internal components, leading to intermittent operation or complete failure.

Compatibility And Notes

This part is marketed for the listed Citroën and Peugeot models. Always verify the part number (9101LW / EZRC) against the vehicle’s existing handle to confirm fitment. Availability in multiple factory colors reduces or eliminates the need for repainting prior to fitment.

This exterior door handle is a direct-fit replacement for the left front (driver’s) door on selected Citroën and Peugeot models. Supplied in EWP (White Banquise) finish, it restores the original appearance and reliable operation after wear or impact. Ideal for professional workshops and experienced DIYers looking for an OEM-style part identified by part number 9101LV.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4 II B7, Citroën C‑Elysée, DS4, Peugeot 301
• Product Codes: 9101LV
• Other Numbers: EWP (Paint White Banquise)

Function And Description

The handle operates the door latch mechanism, transmitting the manual pull action to the internal latch via rods or cables and the handle spindle. It is supplied painted to match the vehicle exterior and designed to interface with the factory locking and latch assemblies for a secure, flush fit.

Common Failure Causes

• Impact Damage: Damage from door impacts or collisions is the most frequent cause of breakage.
• Wear And Fatigue: Repeated use can cause pivot points, springs, or internal plastic components to wear or crack.
• Corrosion And Seizure: Corrosion of internal metal parts or contamination can impair movement and cause sticking or failure.
• Broken Clips Or Linkage: Mounting clips or connecting rods can snap, preventing proper operation.

Replacement Procedure

Typical replacement steps (vehicle-specific details may vary):

• Remove the inner door trim panel and any moisture barriers to access the handle mounting area.
• Disconnect the linkage rods or cables from the handle and release any retaining clips.
• Unscrew or unbolt the handle retaining fasteners and withdraw the old handle from the door shell.
• Install the new handle, secure fasteners to the manufacturer specification, reconnect linkage and clips, and verify smooth operation of the latch and lock.
• Reinstall the door trim and test the door open/close and locking functions before completing the job.

Installation Recommendations

• Use Proper Tools: Small ratchets, Torx/hex bits, trim removers, and needle-nose pliers make the job easier and reduce the risk of damage.
• Replace Damaged Clips: Fit new retaining clips and fasteners when old ones are worn or broken for a secure installation.
• Lubricate Moving Parts: Lightly lubricate latch pivots and linkage with an appropriate grease to prevent future binding.
• Safety Precautions: If Working Near Airbags Or Electrical Modules, Follow Manufacturer Safety Procedures; Disconnect Battery If Required By The Service Manual.
• Final Check: Ensure Proper Alignment And Smooth Operation Of The Handle, Latch, And Central Locking Before Reassembling Interior Trim.

Why Choose This Part

Part Number 9101LV in EWP White Banquise provides a color-matched, OEM-style repair for visible exterior damage or worn handles. The part is aimed at mechanics and competent DIYers who need a reliable, direct-fit replacement to restore both function and appearance.

Compatibility Notes

Fits Left Front (Driver) Door On: Citroën C4 II B7, Citroën C‑Elysée, DS4, Peugeot 301. Check the part number 9101LV and color code EWP to ensure match with the vehicle’s exterior finish.

Upgrade or replace your worn or damaged exterior door handle with this OE-fit left front (driver side) door handle designed for Citroën and Peugeot models. Manufactured to match the original shape and mounting points, this unit restores reliable operation of the driver’s door latch and retains factory appearance when painted in Grey Metallic EZRC (Grey Aluminium finish). Ideal for professional garages and DIY mechanics searching by part code 9101LV or EZRC.

Key Features

• Direct Fit For Models: Citroën C4 II (B7), C‑Elysée, DS4, Peugeot 301.
• Finish: Grey Metallic EZRC (Paint Grey Aluminium). Other colors available from stock.
• Side: Left Front (Driver’s Door).
• Part Codes: 9101LV, EZRC — commonly referenced in catalogs and parts searches.
• Designed To Match Factory Mounting Points And Appearance.

Function And Common Issues

The exterior door handle operates the mechanical linkage between the outside lever and the door latch. It is not a scheduled wear item, but frequent use, exposure to moisture and road salts, or mechanical impact can cause failure. Typical problems include cracked or broken plastic housings, worn pivot points, detached retaining clips, damaged paint, and, in rare cases, internal corrosion of metal components.

How Replacement Is Performed

General replacement steps (for experienced technicians or competent DIYers):

• Remove the interior door trim panel to access the handle mounting area and door internals.
• Disconnect the exterior handle linkage rods or cables from the latch mechanism—note orientation for reassembly.
• Unscrew or release the retaining bolts/clips holding the handle to the door shell and remove the old unit.
• Fit the new handle, secure fasteners, reconnect linkage and any electrical connectors (if present), and test operation of the latch and lock/unlock function.
• Reinstall the door trim panel, check for correct alignment and smooth movement of the handle and latch.

Mounting Recommendations

• Use Proper Tools: Trim tools for door cards and a torque-aware driver for fasteners to avoid damaging plastic retainers.
• Check And Replace Damaged Clips: Inspect and replace any broken retaining clips or seals found during disassembly.
• Lubrication: Lightly lubricate pivot points and linkage with a suitable grease to ensure smooth operation and reduce wear.
• Paint Protection: Mask surrounding paint when replacing a painted handle to avoid scratches; touch up any exposed metal to prevent corrosion.
• Function Test: Verify mechanical operation and central locking (if applicable) before final reassembly.

Why The Part Fails Most Often

• Material Fatigue: Repeated use leads to cracking or wear of plastic components and pivots.
• Broken Retaining Clips: Clips that secure the handle frequently break during operation or removal.
• Impact Damage: Door dents or accidental impacts can deform or fracture the handle assembly.
• Environmental Effects: Corrosion from moisture and road salt can impair metal components and linkages over time.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4 II (B7), C‑Elysée, DS4, Peugeot 301
• Product Codes: 9101LV, EZRC
• Additional Numbers: N/A

This door handle is suitable for professional repair shops and competent DIY enthusiasts who need a reliable, correctly fitting replacement part. Searchable by part code 9101LV and EZRC for quick identification in parts lists and online catalogs.

High-quality exterior door handle for Citroën and Peugeot models, ideal for professional workshops and DIY mechanics. This replacement handle (code 9101LW) is finished in EWP Banquise White and matches the factory paint for a seamless appearance. The handle performs the primary function of mechanically operating the door latch and linkage, providing reliable opening and closing while maintaining the original look of the vehicle. Designed to withstand daily use, it is a direct-fit part for compatible models and restores full functionality after a broken or worn exterior handle.

Benefits And Features

• Direct fit for Citroën C4 II (B7), C-Elysée, DS4, and Peugeot 301 where the 9101LW code applies.
• Factory-matching Banquise White (EWP) finish for consistent exterior appearance.
• Durable construction with replacement mounting points and linkage connection for quick installation.
• Stock availability in multiple colors for paint-matched repairs.
• Ideal for body shops, service garages, and competent DIY enthusiasts seeking a precise fit.

Technical Information

• Manufacturer: Stellantis (Citroën / Peugeot)
• Model: Citroën C4 II (B7), Citroën C-Elysée, DS4, Peugeot 301
• Product Codes: 9101LW
• Additional Numbers: Color Code EWP – Banquise White

Installation Recommendation

Replacement is straightforward for technicians familiar with door panel removal. Typical steps:

• Tools Required: Trim removal tools, Torx and Phillips screwdrivers, 8–10 mm socket set, pliers.
• Disconnect Battery If Working Near Electronic Components And Follow Safety Practices.
• Remove Interior Door Trim Panel Carefully To Access The Handle Mechanism And Linkages.
• Unbolt Or Unclip The Old Handle From The Outside, Disconnect The Linkage Rods And Any Electrical Connectors If Present.
• Install New Handle By Reattaching Linkage Rods, Securing Bolts Or Clips And Testing Mechanism Before Reassembling The Door Panel.
• Verify Smooth Operation Of Locking And Opening Functions, Adjust Linkage If Necessary.

Estimated Time: Approximately 30–60 Minutes Per Door For Experienced Technicians.

Why This Part Most Frequently Fails

• Plastic Fatigue And Wear: Many exterior handles contain plastic components and clips that become brittle over time, leading to breakage during operation.
• Mechanical Stress And Impact: Parking impacts or forced opening attempts can crack or deform the handle.
• Corrosion And Seizure: Metal linkages or fasteners exposed to moisture and road salt can corrode, preventing smooth movement and causing extra load on the handle.
• Internal Linkage Failure: Separation or bending of the internal rods and clips often makes the handle ineffective even if the visible part looks intact.
• Paint Damage And Weathering: Repeated exposure to UV and harsh environments can degrade the finish, prompting replacement for aesthetic reasons as well.

Notes For Purchase

Search Keywords: Door Handle 9101LW, Banquise White Door Handle, Citroën C4 II Door Handle, Peugeot 301 Door Handle, C-Elysée Handle, DS4 Handle. Check The Product Code 9101LW To Ensure Color And Fitment Match Your Repair. Multiple Color Options Are Available From Stock For Bodywork Matching.

Replace a worn or damaged exterior door handle with a direct-fit part designed for Citroën and Peugeot vehicles. This left front (driver side) handle, referenced KCA / 9101LV, features a painted Gray Artense finish and is suitable for workshop fitment or competent DIY repairs. The replacement restores proper door operation, improves appearance and maintains vehicle security. Common search terms include part number 9101LV, KCA door handle, Citroën driver door handle and Peugeot left front handle — useful when locating the exact match.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C4 II (B7), C-Elysée, DS4, Peugeot 301
• Product Codes: 9101LV, KCA
• Additional Numbers: N/A
• Side: Left (Driver)
• Finish: Painted Gray “Artense”

Installation Recommendations

Suitable for professional garages and experienced DIYers. Typical replacement steps:

• Gather basic tools: trim tools, Torx/Screwdriver set, socket set and pliers.
• Remove the inner door trim panel carefully to access the handle mechanism and linkage. Protect trim clips and upholstery.
• Peel back or remove the vapor/water barrier to expose the mounting bolts and rods.
• Disconnect the lock/rod linkages and any electrical connectors if the handle has integrated sensors or lights.
• Unscrew the handle mounting fasteners, remove the old handle and fit the new one in reverse order. Ensure correct alignment of rods and clip retainers.
• Test locking, unlocking and door latch operation before reassembling the door panel.

Tip: If the handle incorporates keyless-entry sensors or an electronic switch, take extra care with connectors and sealings. Test all functions after installation.

Most Common Causes Of Failure

• Mechanical Wear: Repeated use causes plastic clips, levers or internal pivots to fatigue and break over time.
• Corrosion and Moisture Ingress: Water, road salt and dirt can corrode metal components or freeze linkages in cold climates.
• Impact Damage or Vandalism: Door handles are exposed and can crack, deform or detach after impacts.
• Degraded Paint/Finish: Exposure to UV and chemicals leads to finish deterioration, affecting appearance more than function.

This door handle is a straightforward, cost-effective repair that reinstates reliable access to the vehicle. It is frequently searched by part code (9101LV, KCA), so having the correct reference speeds up sourcing and fitment. Designed for direct replacement on the listed Citroën and Peugeot models, it provides a factory-style fit and finish for both workshop professionals and competent self-repairers.

Premium exterior door handle designed for Citroën and Peugeot models, offered in factory-matching KCA Artense Grey paint. Ideal for professional garages and DIY enthusiasts who need a reliable replacement part that restores appearance and function. The handle is suitable for front and rear doors on the listed models and is often searched by part code 9101LW — include this code when ordering to speed up identification and ensure correct fitment.

Technical Information

• Manufacturer: Stellantis (Citroën/Peugeot)
• Model: Citroën C4 II (B7), Citroën C‑Elysée, DS4, Peugeot 301
• Product Codes: 9101LW
• Additional Numbers: Color Code KCA (Paint: Artense Grey)

Fit And Function

This is an exterior door handle that replaces worn, broken or cosmetically damaged handles. It restores smooth opening and closing of the door latch and is finished in OEM-style paint for a factory look. The handle assembly includes the external lever and mounting points; confirm whether internal linkage or fasteners are reused from the original unit when removing the old handle.

Installation Recommendations

• Tools Needed: trim tools, Torx/Phillips bits, socket set, possible clip pliers. Typical job time: 30–60 minutes per door for an experienced mechanic.
• Remove the interior door trim panel carefully to access the handle mounting screws and linkage rods. Keep all fasteners and clips for reuse if they remain undamaged.
• Disconnect linkage rods from the old handle, unfasten mounting screws, and remove the handle from the outside. Compare the new handle with the old one to confirm matching mounting points and link rod orientations.
• Install the new handle by reversing removal steps: secure mounting screws, reconnect linkage rods, test latch operation before reassembling the door trim. Adjust rod clips if necessary to eliminate slack.
• Finish: check door alignment and locking function; touch up any paint chips if required. For painted parts, avoid aggressive solvents or abrasion that could damage the finish.

Most Common Causes Of Failure

• Broken Plastic Clips Or Retainers: These are prone to fatigue and often fail during repeated use or when doors are slammed.
• Internal Mechanism Wear: Metal or plastic components inside the handle/latch wear over time, causing stiffness or failure to release the latch.
• Corrosion And Environmental Damage: Salt, moisture and road debris can corrode linkages and fasteners, impairing movement.
• Impact Or Vandalism: External damage from accidents or forced entry commonly cracks or deforms the handle.

Searching by part number 9101LW and color code KCA (Artense Grey) will help you find the exact match faster. Suitable for workshop replacement or competent DIY repair; if internal lock cylinder replacement is required, ensure compatibility with existing lock parts.