This interior right-side door handle is a direct-fit replacement for Citroën C3 III models and carries OEM references 9825130577 and 98012885VV. Designed for mechanics and experienced DIYers, the part restores reliable mechanical operation of the door latch and smooth opening action. It is an economical way to eliminate rattles, broken levers or a non‑responsive handle without replacing the complete door trim or latch assembly. Compatible with right front and right rear applications where the original part numbers match.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 III (Third Generation) — Right Front And Right Rear Doors
• Product Codes: 9825130577
• Other Numbers: 98012885VV

Function

The inner door handle transmits the user’s pull force to the door latch mechanism via a mechanical rod or cable, allowing the door to open from the inside. It also serves as an ergonomic interface integrated into the door trim and helps keep the trim panel secured. The handle must move smoothly, engage the latch reliably and sit flush with the interior panel to avoid noise and wear.

Why The Part Fails Most Often

Common failure modes include plastic lever fracture or fatigue, worn or detached linkage (rod or cable), broken retaining clips, and internally worn pivot points or springs. Failure is often accelerated by repeated heavy use, impact (door slamming), deformation from improper removal or reinstallation of door trim, and dirt or corrosion in the mechanism. Symptoms include a loose or wobbly handle, door that does not open from the inside, or audible rattles from the door panel.

Installation Recommendations

Removal and replacement is straightforward for a qualified mechanic or competent DIYer with basic hand tools. General steps:

• Carefully remove the door trim panel and any decorative covers to access the inner handle mounting screws and linkage. Keep all fasteners and trim clips organized.
• Disconnect the linkage rod or release the cable end from the handle assembly. Note or photograph the linkage orientation for correct reassembly.
• Unscrew or unclip the old handle and remove it from the trim. Inspect the surrounding trim clips and access holes for damage.
• Fit the new handle, secure with the original fasteners and reconnect the rod or cable ensuring correct engagement and motion without binding.
• Test the handle operation (open and close) several times before reattaching the trim panel. Reassemble trim and verify all electrical connectors (e.g., switches) are properly seated if applicable.

Typical replacement time: approximately 20–60 minutes depending on experience and whether the work is on the front or rear door. Use trim tools to avoid damaging panels. If the door contains powered components or airbags, follow manufacturer safety procedures; in such cases disconnecting the battery prior to work may be recommended by the vehicle manufacturer.

Practical Tips For A Durable Repair

• Check the condition of the linkage rod/cable and replace if frayed or bent.
• Lubricate pivot points and the latch mechanism with a light grease to reduce wear and noise.
• Replace broken trim clips to prevent panel movement and subsequent stress on the handle mounting points.
• After installation, confirm central locking and child locks function correctly (if fitted).

Compatibility And Notes

Fits Citroën C3 III where OEM numbers match: 9825130577 and 98012885VV. Always verify part numbers against the vehicle’s existing part for a direct fit. This part is supplied as a replacement interior handle for the right side (front and rear) configuration.

High-quality replacement interior door handle designed for the left-side doors of Citroën C3 III. Ideal for professional mechanics and DIY enthusiasts who need a direct-fit part with known reference numbers 9825130877 and 98012886VV. This handle restores reliable door opening and closing, improves cabin ergonomics and maintains the original appearance of the vehicle interior.

Why Choose This Door Handle

This part is a practical, cost-effective solution when the original handle shows wear or damage. It is commonly searched by its product codes, so having the correct reference ensures quick identification. The design matches factory mounting points and cable/rod connections to simplify replacement and reduce workshop time.

How It Works And Where It Fits

The interior door handle operates the mechanical linkage or cable that releases the door latch when pulled. It is suitable for the left front and left rear doors of the Citroën C3 III. When fitted correctly, the handle provides smooth operation and consistent engagement with the door latch mechanism.

Replacement Procedure (Overview)

• Prepare Tools: Trim removal tools, Torx/screwdrivers, pliers.
• Safety: Disconnect the negative battery terminal if working near electrical components to avoid short circuits.
• Remove Door Trim: Carefully pry off trim clips and remove the door card to access the handle mechanism.
• Disconnect Linkage: Unclip or unscrew the rod/cable from the old handle.
• Remove Old Handle: Unscrew the retaining fasteners and take out the damaged handle.
• Install New Handle: Position the new handle, secure fasteners, and reconnect linkage ensuring correct orientation and free movement.
• Reassemble Door: Refit the door card and test the handle operation for smooth open/close both from inside and outside.

Installation Recommendations

• Use appropriate trim tools to avoid damaging door panels.
• Check linkage clips and rods for wear and replace if necessary when doing the repair.
• Ensure all fasteners are tightened to manufacturer torque where specified and that the handle engages the latch without binding.
• Test door lock/unlock and child lock functions after installation to confirm correct operation.

Most Common Failure Reasons

• Plastic fatigue or breakage of pivot points and mounting tabs due to repeated use or forceful handling.
• Wear of the internal contact surfaces causing sloppy or unreliable operation.
• Broken or detached linkage clips/rods preventing the handle from actuating the latch.
• Sunlight/heat exposure accelerating material degradation in older vehicles.

Technical Information

• Manufacturer: Citroën (Stellantis)
• Model: Citroën C3 III
• Product Codes: 9825130877, 98012886VV
• Other Numbers: 98012886 VV

This interior left door handle is aimed at professionals and experienced DIYers who require a dependable replacement with clear reference numbers for fast identification. Order now to restore proper door function and interior appearance on your Citroën C3 III.

Product Overview

High-quality exterior left rear door handle designed for a range of Citroën and Peugeot models. This color-matched unit (ELS Almond Green) replaces a broken, cracked or worn original handle and restores reliable door opening and locking operation. Ideal for professional workshops and DIY mechanics looking for a direct-fit replacement with OEM cross-reference 1609240780 / 980297831T. The handle is supplied ready for fitment to the driver-side rear door and is intended to match factory paint for a seamless finish.

Key Benefits

• Direct Fit For Multiple Models: Minimizes modification and installation time.
• Color Matched (ELS Almond Green): Reduces need for repainting and simplifies bodywork.
• Restores Proper Operation: Replaces worn mechanisms, broken lever or damaged mounting points.
• Suitable For Workshops And Home Mechanics: Clear fitment and serviceability.

Technical Information

• Manufacturer: Stellantis (Citroén / Peugeot)
• Model: Citroën C3 III; Citroën C4 Picasso; Citroën Berlingo III; Peugeot 308; Peugeot 3008; Peugeot 5008; Peugeot Partner III; Peugeot Rifter
• Product Codes: 1609240780, 980297831T
• Other Numbers: ELSB (Color Code / Paint Reference: Almond Green)

Installation Recommendation

Replacement is straightforward for anyone with basic workshop tools. Typical procedure:

• Remove Interior Door Trim: Carefully pry off the door card using trim tools to avoid breaking clips.
• Disconnect Linkages: Unclip or unfasten the door latch rods and any electrical connectors for central locking or sensors if present.
• Remove Fasteners: Unscrew or unbolt the handle retaining screws from the inner door shell.
• Extract Old Handle: Pull the old handle out from the outside and free any remaining clips or seals.
• Fit New Handle: Position the new handle, secure the retaining fasteners, reconnect the rods and connectors, and test mechanical and locking function before reassembling the door card.
• Final Check: Ensure smooth operation of the handle and central locking. Replace any worn clips or seals to prevent rattles or water ingress.

Most Common Failure Reasons

• Plastic Fatigue And Breakage: Repeated use and mechanical stress lead to cracking of plastic components.
• Corrosion Or Seizure: Moisture ingress and salt accelerate corrosion on metal fasteners and pivot points, causing stiff or failed operation.
• Damaged Linkage Clips Or Rods: Broken or deformed clips cause the handle to operate loosely or fail to open the latch.
• External Impact Or Vandalism: Physical damage from bumps, attempted break-ins or accidents frequently cracks or detaches the handle.
• Paint Wear And Surface Damage: Scratches and paint failure around the handle area compromise appearance and can expose substrate to corrosion.

Notes For Purchase

Check the part numbers (1609240780, 980297831T) and the color code (ELS / Almond Green) against the vehicle requirement to ensure correct fit and finish. This handle is intended for the left rear (driver-side rear) door.

This OEM-style left front exterior door handle is designed for direct replacement on a range of Citroën and Peugeot models. It fits driver-side doors and includes a cutout for a mechanical key cylinder, preserving original locking function and appearance in Almond Green (ELS) finish. The part is suitable for mechanics and experienced DIYers who need a reliable exterior handle to restore proper door opening, locking and to match factory paint.

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C3 III, Citroën C4 Picasso, Citroën Berlingo III, Peugeot 308, Peugeot 3008, Peugeot Partner III
• Product Codes: 1609240280, 980297811T, ELSB
• Other Numbers: Color Code ELS (Almond Green)

Function And Features

The handle provides the mechanical interface for opening the driver-side front door and accommodates the key cylinder for manual locking/unlocking. It houses the lever that actuates the door latch and interfaces with the interior release rod/cable and central locking actuator. The Almond Green (ELS) finish is matched to factory paint for a consistent exterior appearance.

Installation Recommendations

• Prepare: Work on a stable surface and have basic trim tools and a small ratchet set available.
• Door Trim Removal: Remove the inner door panel carefully to access the handle mounting screws, retaining clips and rods. Protect trim clips to avoid breakage.
• Disconnect Linkages: Detach the latch rod/cable and any electrical connector for a handle-mounted switch (if present).
• Remove Old Handle: Unscrew or unclip the handle from the exterior mounting points. Keep track of screws and spacers for reuse or replacement.
• Fit New Handle: Position the replacement handle, reconnect the latch rod/cable and ensure the key cylinder aligns correctly with the cutout. Secure all fasteners to the original torque if available.
• Test Before Reassembly: Operate the handle from outside and inside, operate the key cylinder and verify central locking function before refitting the door trim.
• Final Checks: Ensure paint edges are not pinched, that the handle moves freely, and that weather seals sit correctly to prevent leaks.

Why The Part Typically Fails

• Mechanical Wear: Repeated use causes internal lever wear and weakened mounting tabs, eventually leading to loose or non-functioning handles.
• Impact Or Vandalism: Physical damage from impacts or forced entry can crack the handle or distort attachment points.
• Corrosion And Environmental Damage: Moisture and road salts can corrode metal components and seize moving parts or deteriorate plastic clips.
• Key Cylinder Wear: When present, the key cylinder can wear or seize, which affects the entire handle assembly operation.
• Broken Plastic Clips/Tabs: Common failure on aging vehicles where plastic fastening tabs become brittle and break during operation or removal.

Notes For Mechanics And DIYers

When replacing the handle, inspect the door latch, actuator and linkage for wear or damage and replace any worn clips or rods at the same time to ensure long-term reliability. Use appropriate corrosion protection on metal fasteners and avoid over-tightening screws that could crack the new handle’s mounting points. After installation, verify that the lock cylinder (if reused) is lubricated and operates smoothly.

Compatibility And Fitment

This handle is listed for the models above and commonly referenced by product codes 1609240280 and 980297811T. Always compare the appearance, mounting points and keyway orientation with the original part before fitting to ensure correct match.

Replacement Right-Side Door Handle Designed For Professional Workshops And DIY Enthusiasts. This OE-Fit Handle With Codes 1609239680 / 980297821T (ELSB) Offers Direct Compatibility With Multiple Stellantis Models, Ensuring Correct Fit, Function, And Finish. The Almond Green Painted Surface Matches Factory Color ELS For A Clean Visual Match On Vehicles With The Same Paint Option. Commonly Searched By Part Number 1609239680, This Handle Is Ideal For Mechanics Looking For A Reliable Passenger-Side Front Or Rear Replacement.

Key Features

• Direct Fit For Passenger-Side Front And Rear Doors (Right Side)
• OEM Compatibility With Citroën And Peugeot Models Listed Below
• Painted Finish: ELS Almond Green For Visual Match To Original Bodywork
• Robust Mechanism Designed For Everyday Use And Central Locking Integration
• Easy Identification By Product Codes 1609239680, 980297821T, ELSB

Technical Information

• Manufacturer: Stellantis / Citroën / Peugeot
• Model: Citroën C3 III; Citroën C4 Picasso; Citroën Berlingo III; Peugeot 308; Peugeot 3008; Peugeot Partner III
• Product Codes: 1609239680; 980297821T; ELSB
• Other Numbers: Paint Code ELS (Almond Green)

Function And Typical Failure Modes

The Door Handle Operates The Latch Mechanism To Open The Door From The Outside And Interfaces With The Lock/Central Locking Mechanism. Common Reasons For Failure Include Mechanical Wear Of Internal Plastic Or Metal Components, Broken Mounting Tabs Or Clips Due To Force Or Impact, Corrosion Of Internal Linkages, And Paint Or Surface Damage From Road Debris. Failures Most Often Manifest As Stiff Operation, Intermittent Release, Or Complete Breakage Of The Lever Or Mounting Points.

How To Replace

Basic Replacement Steps (General Guidance):

• Remove The Interior Door Trim Panel To Access The Handle Mechanism And Linkages.
• Peel Back The Moisture Barrier Carefully To Avoid Tearing.
• Disconnect The Rods Or Clips That Link The Handle To The Latch (Note Their Orientation For Reassembly).
• Unscrew The Fasteners Securing The Exterior Handle And Remove The Old Handle.
• If Required, Transfer The Lock Cylinder Or Any Retaining Clips From The Old Unit To The New One.
• Fit The New Handle, Reinstall Fasteners, Reconnect Linkages, And Test Mechanically And Electrically (Central Locking Where Applicable).
• Reassemble The Door Trim And Verify Smooth Operation And Proper Locking.

Installation Recommendations

• Use Appropriate Trim Tools To Prevent Damage To Interior Panels And Paint.
• Inspect The Linkage Clips And Fasteners; Replace Any Damaged Clips To Ensure Reliable Operation.
• Lubricate Moving Linkages Lightly With Suitable Grease To Reduce Wear And Noise.
• When Replacing A Painted Handle, Protect Surrounding Paintwork During Removal And Installation.
• After Installation, Test Door Opening, Latching, And Central Locking (If Present) Several Times To Confirm Correct Function.

Why This Part Most Commonly Breaks

Door Handles Suffer From Repeated Mechanical Stress, Exposure To Moisture And Road Salts, And Occasional Impacts (Parking Scrapes Or Minor Collisions). Internal Plastic Clips And Levers Are Typical Weak Points That Degrade Over Time, While Corrosion Can Cause Linkages To Seize. UV Exposure And General Wear Can Also Affect Painted Finishes, Leading Owners To Replace Handles For Both Functional And Cosmetic Reasons.